Numerical Flow Simulation in Turbine Mode of Counter-Rotating Type Pumping Unit to Cooperate with Wind Turbine

This serial research has proposed the hybrid power system combined the wind power unit with the counter-rotating type pump-turbine unit, to provide the constant output for the grid system, even at the suddenly fluctuating/turbulent wind circumstance. In this paper, the tandem impellers prepared for the counter-rotating type pumping unit were operated at the turbine mode, and the performances and the flow conditions were investigated numerically with accompanying the experimental results. Even though providing the pumping unit for the turbine mode, the maximum hydraulic efficiency is close to one of the counter-rotating type hydroelectric unit designed exclusively for the turbine mode. Besides, the runners/impellers of the unit work evidently so as to coincide the angular momentum change through the front runners/impellers with that through the rear runners/impellers, namely to take the axial flow at not only the inlet but also the outlet, without the guide vanes. From these results, it can be concluded that this type unit is effective to work at not only the pumping but also the turbine modes.     

Photocatalytic properties of titanium dioxide sputtered on a nanostructured substrate

The effective one-step physical approach is demonstrated for the fabrication of anatase titanium dioxide nanotubes through r.f. magnetron sputtering of TiO₂ on a highly ordered nanoporous anodic alumina template. The nanostructured TiO₂ benefited from the combination of unique properties of both the sputtering technique that provided well-controlled environment for the fabrication of anatase phase TiO₂ and the porous anodic alumina (PAA) that provided uniform and ordered nanopores. The photocatalytic properties of TiO₂ films were characterized following the degradation of methylene blue molecules under UV light irradiation. The photocatalytic activity of the nanostructured TiO₂ films has been found to be approximately twice higher in comparison with the flat TiO₂ films fabricated at the same conditions.     

Consideration on the Relationship Between Dielectric Breakdown Voltage and Water Content in Fatty Acid Esters

Mineral oil is commonly used as an electrical insulating oil in transformers because of its relatively high electrical insulating ability and fluidity. Considering the depletion of resources and environmental problems, however, fatty acid esters synthesized from natural plant oils are attracting attention as an environmentally friendly insulating oil. In addition, fatty acid esters such as methyl octanoate, methyl dodecanoate, 2-ethylhexyl octanoate, and 2-ethylhexyl dodecanoate have high fluidity, and also show excellent moisture tolerance against dielectric breakdown compared to mineral oil. In the present study, to clarify the reason for the superior moisture tolerance of fatty acid esters, the status of dissolved water in esters is investigated with IR spectroscopic measurements and density functional theory (DFT) calculations. It is revealed that water molecules in fatty acid esters are trapped by the ester moiety of fatty acid esters. As a result, fatty acid esters have a higher moisture tolerance against dielectric breakdown than mineral oil.     

RF sources for ITER Ion Cyclotron H&CD system

The Ion Cyclotron Heating and Current Drive (IC H&CD) system for ITER will provide 20 MW to the plasma. The associated Radio Frequency (RF) source system has to be compliant with all operation modes foreseen in that frame. Their specifications are fully described in this paper and constraints on IC RF source components are detailed, in particular concerning the final stage tube of the amplifier. Results of tests performed under a collaborative work at the National Institute for Fusion Science (NIFS) facility are presented. Consequences on the procurement process by ITER India (II) are deduced.     

Clarification of strain limits considering the ratcheting fatigue strength of 316FR steel

The effect of ratcheting on fatigue strength was investigated in order to rationalize the strain limit as a design criterion of commercialized fast reactor systems. Ratcheting fatigue tests were conducted at 550 °C. Duration of the ratchet straining was set for a certain number of strain cycles taking the loading condition of fast reactors into account, and the number of cycles for strain accumulation was defined as the ratchet-expired cycle. Fatigue lives decrease as the accumulated strain by ratcheting increases. Mean stress increased during the ratcheting cycle and its maximum value depended on the accumulated strain and the ratchet-expired cycle. Fatigue life reduction was negligible when the maximum mean stress was less than 25 MPa, corresponding to an accumulated strain of 2.2%. Accumulated strain is limited to 2% in the present design guidelines and this strain limit is considered effective to avoid reducing fatigue life by ratcheting. Microcrack growth behaviors were also investigated in these tests in order to discuss the life reduction mechanisms in ratcheting conditions.     

Oxygen permeation properties and surface modification of acceptor-doped CeO2/MnFe2O4 composites

The preparation and oxygen permeation properties of the (Ce_0.8Pr_0.2)O_2−δ − x vol% MnFe₂O₄ composites, where x = 0 to 35, have been investigated. The samples were prepared by the Pechini method. In the case of Ce_0.8Pr_0.2O_2−δ, an oxygen flux density of 6 μmol⋅cm⁻²⋅s⁻¹ (L = 0.0247 cm) and the maximum methane conversion of 50% were attained at 1000^∘C. Unlike composites consisting of Gd-doped CeO₂ and MnFe₂O₄, the oxygen permeability of the (Ce_0.8Pr_0.2)O_2−δ – x vol% MnFe₂O₄ composites was almost constant regardless of the volume fraction of MnFe₂O₄; however, the optimum volume fraction of MnFe₂O₄ was determined to be 5 to 25 in the context of the chemical and mechanical stabilities under methane conversion atmosphere. In addition, the surface modification of the (Ce_0.8Gd_0.2)O_2−δ – 15 vol% MnFe₂O₄ composite was performed by using the FePt nanoparticles. The catalyst loading of 2.8 mg/cm² on the both side of the 0.3 mm-thick (Ce_0.8Gd_0.2)O_2−δ – 15vol% MnFe₂O₄ composite increased the oxygen flux density from 0.30 to 0.76 μmol⋅cm⁻²⋅s⁻¹ in the case of He/air gradients; however, the effect seems to be reduced in the case of high oxygen flux density caused by a large pO₂ gradient. Moreover, the Langmuir-Blodgett film of the FePt nanoparticles were successfully prepared on the tape-cast (Ce_0.8Gd_0.2)O_2−δ – 15vol% MnFe₂O₄ composite. Hydrophobic treatments for the surface of the composite were crucial to achieve high transfer ratio for the deposition of the LB film.     

Analysis of a gyroscopic force measuring system in three-dimensional space

This paper concerns the development of an entirely new sensor for measuring forces using a gyroscope (called gyroscopic force measuring system, or simply GFMS) for measuring a force vectorially. In a previous paper [S. Kurosu, M. Adachi, K. Kamimura, Dynamical characteristics of gyroscopic weight measuring device, ASME J. Dynamic System Measurement, and Control 119 (1997) 346–350], the dynamics of the GFMS for measuring a vertical force were investigated and the principal characteristics were examined theoretically and experimentally. The results of this work are directly applicable to measurement of a vectorial force in three-dimensional space. The principle and the dynamical characteristics of the GFMS for measuring a force vector are analyzed theoretically. To measure a force vectorially, two auxiliary turntables (driven by servomechanisms) are installed around the gyroscope, in which turntable outputs are required to follow some angles of incidence of a force vector. Some unfavorable errors caused by various factors and disturbances are analyzed. Two types of compensation methods are proposed as a device both for accurate force measurement and disturbance suppression. The feasibility of the proposed GFMS is confirmed by numerical simulations.     

Spherulitic formation and characterization of partially fluorinated copolymers and their nanohybrids with functional fillers

Poly[vinylidenefluoride‐co‐(tetrafluoroethylene)] (P(VDF‐TeFE)) exhibited clear spherulitic texture with negative birefringence. The number and growth rates of the spherulites decreased at high crystallization temperature than at low crystallization temperature. Nonetheless, overall larger spherulites were found at high crystallization temperature and the brightness of the spherulites increased very fast at low crystallization temperature, thereafter it seemed as diminution of birefringence. AFM was used to investigate the impact of organo modified nanodiamond(ND) on spherulitic textures, lamellar thickness, and thickness distribution of P(VDF‐TeFE) copolymer. Poly[ethylene‐co‐(tetrafluoroethylene)] (ETFE) also confirmed spherulites structure and the boundaries could be clearly observed. By incorporation of the organo modified nanodiamond (ND) and organo‐modified montmorillonite (MMT) in fluropolymer matrix, it was found that spherulitic texture was seriously disordered and their nanohybrids was found only to have poorly developed spherulite structure. Both of the nanohybrids samples show better crystallization temperature as compared to their neat copolymer samples. Furthermore, the incorporation of nanoparticles decreased the size of the spherulites. POLYM. ENG. SCI., 57:161–171, 2017. © 2016 Society of Plastics Engineers     

Determination of the Temperature Coefficient Distribution of Dielectric Ceramics Using Scanning Photothermal Dielectric Microscopy

Two-dimensional images of the distribution showing the temperature coefficient of the dielectric constant for two types of two-phase composite ceramics composed of TiO₂-Bi₂Ti₄O₁₁ and BaTi₄O₉-BaPr₂Ti₄O₁₂ were obtained using scanning photothermal dielectric microscopy. The images of the TiO₂-Bi₂Ti₄O₁₁ ceramic showed that the TiO₂ and Bi₂Ti₄O₁₁ grains had negative and positive temperature coefficients, respectively, and that the macroscopic averaged temperature coefficient of the ceramic was relatively low because of the cancellation of the opposite signs of the coefficients. On the other hand, the images of the BaTi₄O₉-BaPr₂Ti₄O₁₂ ceramic showed that the temperature coefficient of both grains had the same sign (negative), although their absolute values were quite different.     

Dynamic properties of an all solid-state frequency-shifted feedbacklaser

Frequency-shifted feedback (FSF) laser exhibits outstanding features in its oscillation spectrum. We analyze build-up dynamic properties of the FSF laser by means of rate equation and analyze steady-state dynamic properties of the FSF laser by means of Wigner-Ville distribution of intracavity electric field. Furthermore, we analyze instantaneous oscillation frequency at peak spectral intensity and oscillation bandwidth of its spectrum using the formula of instantaneous spectral intensity derived from Wigner-Ville distribution of intracavity electric field. These analytical results are in good agreement with the experimental ones which have been observed by a diode-pumped Nd:YVO₄ FSF laser. It becomes clear that the FSF laser supports many frequency components simultaneously even though the gain medium is homogeneously broadened and has a continuously chirped frequency components of comb in which the creation of chirped frequency components are strongly correlated in phase because of a replica of the preceding components. Also, the instantaneous oscillation frequency is closely related to the detuning frequency which depends on the total net gain in the cavity and the gain bandwidth of atomic transition. The oscillation bandwidth is defined as the product of the saturation-broadened bandwidth and the total resonant modes contributing to FSF operation