Moving pick‐up‐type contactless power transfer systems and their efficiency using series and parallel resonant capacitors

The equivalent circuit, the efficiency, and the important characteristics of moving pick‐up type contactless power transfer systems are described. If the primary series capacitor and the secondary parallel capacitors are chosen correctly and the winding resistances are ignored, the equivalent circuit of the transformer with these capacitors becomes the same as an ideal transformer at the resonant frequency. This simple approximation helps to understand the phenomena occurring with load changes. Because the circuit analysis becomes simple, the approximate value of the power transfer efficiency can be derived. This paper describes the determination of the capacitor values, the derivation of the equivalent circuit and the efficiency, and test results. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 172(2): 47–54, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20970     

Suppression of creep cavitation in precipitation-hardened austenitic stainless steel to enhance creep rupture strength

Extensive creep cavitation in Ti, Nb and Cu containing precipitation hardened austenitic steels was found to limit the usefulness of deformation resistance to increase long-term creep rupture strength. The steels were microalloyed with boron and cerium that resulted in increase in creep rupture strength and ductility of the steels significantly. Grain boundary sliding and creep cavity nucleation and growth in the steels were suppressed greatly on microalloying. Auger spectroscopic analysis revealed the segregation of boron instead of sulfur on cavity surface and the absence of sulfur contamination of grain boundary upon the microalloying. Suppression of creep cavitation through the control of trace elements segregation along with the precipitation hardening increased the creep rupture strength of austenitic stainless steels.     

Molecular structures of gellan gum imaged with atomic force microscopy (AFM) in relation to the rheological behavior in aqueous systems in the presence of sodium chloride

Aqueous solutions of gellan gum with comparable molecular mass but with different acyl contents were investigated by atomic force microscopy and rheological measurements in the presence of sodium chloride (NaCl). Results obtained were discussed in relation to our previous report using potassium chloride (KCl) as an added salt. For a low-acyl sample, continuous fibrous network structures were identified microscopically as in the case of KCl. The network structures were more heterogeneous than those formed with KCl in terms of the height distribution of molecular assemblies. Rheological thermal hysteresis between sol–gel transitions was detected as in the case of KCl. The storage modulus (G′) of the gelled system was ca. 15% of the corresponding data with KCl at 20 °C. For a high-acyl sample, no continuous network structures were identified but branches with observable ends were identified as in the case of KCl. The hysteresis was less evident than the corresponding data with KCl and for the low-acyl sample with NaCl. Also, G′ values at 20 °C were ca. 30% and 20% of the corresponding data with KCl and for the low-acyl sample with NaCl, respectively. Continuousness and homogeneity of network structures related to the hysteresis and elasticity of the system, respectively.     

Design Of Anti‐Slip Controller For An Electric Vehicle With An Adhesion Status Analyzer Based On The Ev Simulator

The In this paper, a simulator of a one‐wheel Electric Vehicle system is designed for testing an anti‐slip controller using the Motor‐Generator system. The drive motor of the M‐G system is used to simulate the drive wheel of the Electric Vehicle, and the load motor is used to simulate the load force of the chassis. In the driving process, the torque of the load motor is changed according to the drive force of the chassis that is calculated by the program. So it can simulate the dynamic process of the tire‐road system. Based on this simulator system, an anti‐slip controller based on an Adhesion Status Analyzer is proposed. Information about the wheel speed is acquired by using a Back EMF Observer. A load torque disturbance observer is designed to stabilize the acceleration of the wheels. The Adhesion Status Analyzer is used to generate safe acceleration commands for the anti‐slip controller. When a slip occurs, the anti‐slip controller will decrease the torque quickly, and at the same time, by estimating the dynamic status of adhesion, the Adhesion Status Analyzer will restrain the acceleration command within a safe area. The effectiveness of the proposed approach is verified by using the EV slip simulator.     

Selective and in-situ determination of carbonate and oxide particles in aqueous solution using laser-induced breakdown spectroscopy (LIBS) for wearable information equipment

Laser-induced breakdown spectroscopy (LIBS) has been applied for quantitative analysis of Al₂O₃, CaCO₃ and MgO particles suspended in water. In the single elemental system, the plasma emission intensities of Al, Ca and Mg were linearly increased with concentration of elements in the range of 1.0×10^?5–1.0×10^?3  M, 1.0×10^?4–2.0×10^?3 M and 8.0×10^?5 –4.0×10^?3 M, respectively. We also investigated the concentration dependence of breakdown spectra for suspended mixtures of Al₂O₃, CaCO₃ and MgO particles. The emission lines, such as Al I, Ca I, Ca II and Mg I, were appeared in the LIBS spectrum simultaneously, and each emission peak could be deconvoluted. The plasma emission intensities of Al, Ca and Mg in the multielemental system were also linearly increased with their concentrations in the range of 1.0×10^?5–1.0×10^?3 M, 1.0×10^?4–2.0×10^?3 M and 4.0×10^?4–2.0×10^?3 M, respectively. LIBS was found to be available for quantitative and qualitative measurement of the concentrations of Al₂O₃, CaCO₃ and MgO particles suspended in water. The present results suggest that LIBS is a potentially useful tool for in-situ analysis on particles composition and concentrations for environmental monitoring by the wearable information equipments.     

Two-dimensional multiarray formation of hepatocyte spheroids on a microfabricated PEG-brush surface

A two-dimensional microarray of ten thousand (100 x 100) hepatocyte heterospheroids, underlaid with endothelial cells, was successfully constructed with 100 microm spacing in an active area of 20 x 20 mm on microfabricated glass substrates that were coated with poly(ethylene glycol) brushes. Cocultivation of hepatocytes with endothelial cells was essential to stabilize hepatocyte viability and liver-specific functions, allowing us to obtain hepatocyte spheroids with a diameter of 100 microm, functioning as a miniaturized liver to secret albumin for at least one month. The most important feature of this study is that these substrates are defined to provide an unprecedented control of substrate properties for modulating cell behavior, employing both surface engineering and synthetic polymer chemistry. The spheroid array constructed here is highly useful as a platform of tissue and cell-based biosensors and detects a wide variety of clinically, pharmacologically, and toxicologically active compounds through a cellular physiological response.     

Microassembly of semiconductor three-dimensional photonic crystals

Electronic devices and their highly integrated components formed from semiconductor crystals contain complex three-dimensional (3D) arrangements of elements and wiring. Photonic crystals, being analogous to semiconductor crystals, are expected to require a 3D structure to form successful optoelectronic devices. Here, we report a novel fabrication technology for a semiconductor 3D photonic crystal by uniting integrated circuit processing technology with micromanipulation. Four- to twenty-layered (five periods) crystals, including one with a controlled defect, for infrared wavelengths of 3-4.5 microm, were integrated at predetermined positions on a chip (structural error <50 nm). Numerical calculations revealed that a transmission peak observed at the upper frequency edge of the bandgap originated from the excitation of a resonant guided mode in the defective layers. Despite their importance, detailed discussions on the defective modes of 3D photonic crystals for such short wavelengths have not been reported before. This technology offers great potential for the production of optical wavelength photonic crystal devices.