Terahertz paintmeter for noncontact monitoring of thickness and drying progress in paint film

We propose a paintmeter for noncontact and remote monitoring of the thickness and drying progress of a paint film based on the time-of-flight measurement of the echo signal of a terahertz (THz) electromagnetic pulse. The proposed method is effectively applied to two-dimensional mapping of the painting thickness distribution for single-layer and multilayer paint films. Furthermore, adequate parameters for the drying progress are extracted from the THz pulse-echo signal and effectively applied to monitor the wet-to-dry transformation. The THz paintmeter can be a powerful tool for quality control of the paint film on the in-process monitoring of car body painting.     

Biosynthesis of poly-gamma-glutamic acid in plants: transient expression of poly-gamma-glutamate synthetase complex in tobacco leaves

Transient expression of genes coding for the poly-gamma-glutamate (gammaPGA) synthetase system (pgs) was investigated in tobacco plants. Three genes of the pgs, pgsA, pgsB and pgsC, were separately placed under the control of the CaMV 35S promoter and introduced into tobacco leaves via Agrobacterium infection. Synthesized gammaPGA in plant tissues was detected immunologically with mouse anti-gammaPGA antiserum which specifically reacts with gammaPGA on a nitrocellulose membrane. Confirmation of gammaPGA biosynthesis in the transient expression analysis in tobacco tissue indicates that subunits of pgs complex were expressed and reassembled in a functional form.     

Direct imaging of molecular chains in a poly(p-xylylene) single crystal

Individual chains comprising a β-form poly(p-xylylene) (PPX) single crystal were resolved with a high resolution electron microscope (JEM-500). In a polymer crystal the important limiting factor for resolution is radiation damage. The total end point dose of a PPX crystal is about 0.5 coulomb cm^?2 for 500 kV electron irradiation which is more than 20 times greater than that for a polyethylene crystal. The high resolution image obtained was processed by optical filtering to reduce noise due to the granularity of film. The processed image, which corresponds to the ab-plane projection of polymer chains, shows clearly the mutual arrangement of each molecule in the crystal. This high resolution image is sufficient to provide a starting point for determining the unknown crystal structure of the β-modification of PPX.     

An efficient maximum-likelihood-decoding algorithm for linear blockcodes with algebraic decoder

A new soft decoding algorithm for linear block codes is proposed. The decoding algorithm works with any algebraic decoder and its performance is strictly the same as that of maximum-likelihood-decoding (MLD). Since our decoding algorithm generates sets of different candidate codewords corresponding to the received sequence, its decoding complexity depends on the received sequence. We compare our decoding algorithm with Chase (1972) algorithm 2 and the Tanaka-Kakigahara (1983) algorithm in which a similar method for generating candidate codewords is used. Computer simulation results indicate, for some signal-to-noise ratios (SNR), that our decoding algorithm requires less average complexity than those of the other two algorithms, but the performance of ours is always superior to those of the other two     

Deformation rate dependence of mechanical properties of epoxy resin at cryogenic temperatures

Effects of deformation rate on the mechanical properties of epoxy resin used in superconducting magnets have been studied at cryogenic temperatures. Compressive and flexural tests were made to reveal the mechanical behaviour. In the case of compressive tests, the increase in the deformation rate caused on increase of elastic modulus and a decrease of breaking stress and strain. In the case of flexural tests, different results in breaking stress were obtained. The results indicate that the following two problems must be elucidated for practical use of polymers in magnets, ie (i) impact strength of the polymers, (ii) the stress condition applied to the polymers in the magnet.     

Filling behavior of UV nanoimprint resin observed by using a midair structure mold

The filling behavior of resin during UV nanoimprint lithography (UV-NIL) was observed by using a “midair structure mold” and by changing the imprint pressure. The midair structure molds were fabricated by electron beam lithography (EBL) using hydrogen silsesquioxane (HSQ) as a negative tone resist. After the fabrication of midair structure mold, two types of surface treatment molds, which were with or without release coating, were prepared. Using these molds, the filling behavior of a UV curable resin was investigated at various pressures. The results indicate that a pressure of approximately 1.2 MPa is necessary for complete filling in the case of molds treated with a release agent. This method demonstrates effect of a release coating for UV-NIL.     

Influence of Heat Treatment on Hydroformability of TRIP Seamless Steel Tube

A low-carbon TRIP seamless steel tube, which is expected to be used in the hydroforming process, was successfully fabricated using piercing, cold-drawing and two-stage heat treatment process. The two-stage heat treatment is one crucial step because it significantly affects the microstructure and mechanical properties of TRIP seam less steel tube. In order to obtain the TRIP seamless steel tube with high hydroformability, several different heat treatment processes were conducted. The effects of heat treatment conditions （intercritical annealing （IA） and isothermal bainite treatment （IBT）） on the TRIP seamless steel tube hydroformability which was determined by free hydraulic bulge test were analyzed. Two different internal pressure boosting velocities of 0.2 and 0.5 MPa/s of free hydraulic bulge tests were adopted to determine the effective stress vs. effective strain curve of TRIP seamless steel tube. The results showed that for the predetermined IA condition, the maximum bulge height increased, but the maximum burst internal pressure decreased, with the increase of IBT holding time from 4 to 6 rain. For the predetermined IBT condition, the maximum bulge height decreased, but the maximum burst internal pressure increased, with the increase of IA holding time from 5 to 10 rain. By analyzing the free hydraulic bulge test results, it was found that the maximum bulge heights of TRIP seamless steel tubes with the internal pressure boosting velocity of 0.5 MPa/s were higher than those when the internal pressure boosting velocity was 0.2 MPa/s. This means that an appropriate deformation rate should be chosen to obtain the optimal hydroformability of TRIP seamless steel tube. In addition, the effective stress vs. effective strain curves of TRIP seamless steel tubes were ohtained with free hydraulic bulge test.