Investigating the effect of silver nanorods embedded in polydimethylsiloxane matrix using nanoindentation and its use for flexible electronics

The stretchable electrodes with excellent flexibility, electrical conductivity, and mechanical durability are the most fundamental components in the emerging and exciting field of flexible electronics. This article proposes a method for fabrication of such a stretchable electrode by embedding silver nanorods (AgNRs) into a polydimethylsiloxane (PDMS) matrix that is grown by a unique glancing angle deposition technique. The surface, mechanical, and electrical properties of PDMS are significantly changed after embedding the AgNRs in it. The results show that surface roughness and polarity increase after AgNRs are embedded in the PDMS matrix. Elastic modulus (E) and hardness (H) decrease with an increase in the indentation load as a result of the indentation depth effect. Due to strong interfacial adhesion of AgNRs embedded in the PDMS matrix, the E and H of nanocomposite are increased by 167.6 and 93.3% compared with PDMS film, respectively. Furthermore, the AgNRs-PDMS film has an electrical resistivity value in the order of 10⁻⁷ Ωm. It remains conductive during various mechanical strains such as bending, twisting, and stretching, which is demonstrated using a light-emitting diode circuit. Simultaneously, the antimicrobial activity of silver could make it a promising candidate for wearable electronics.     

Simultaneous three-dimensional step-height measurement and high-resolution tomographic imaging with a spectral interferometric microscope

A noncontact, nonmechanical scanning, wide-field spectral interference microscope is developed for simultaneous measurement of three-dimensional step-height of discontinuous objects and tomographic imaging. A superluminescent diode (SLD) is used as a broadband light source and a liquid-crystal Fabry-Perot interferometer (LC-FPI) as a frequency-scanning device. By means of changing the injection current to the SLD, the spectral profile of the SLD is equalized, and a constant light input to the interferometer is achieved over the entire frequency-scan range. The Fourier-transform technique is used to determine both the amplitude and the phase of spectral fringe signals. Three-dimensional height distribution of a discontinuous object is obtained from the phase information, whereas optically sectioned images of the object are obtained either from the amplitude information alone or from the combination of both the amplitude and phase information. Experimental results with submicrometer resolution are presented for both step-height measurement and tomographic sectioning.     

An integrated system solution for supply chain optimization in the chemical process industry

This paper considers a complex scheduling problem in the chemical process industry involving batch production. The application described comprises a network of production plants with interdependent production schedules, multi-stage production at multi-purpose facilities, and chain production. The paper addresses three distinct aspects: (i) a scheduling solution obtained from a genetic algorithm based optimizer, (ii) a mechanism for collaborative planning among the involved plants, and (iii) a tool for manual updates and schedule changes. The tailor made optimization algorithm simultaneously considers alternative production paths and facility selection as well as product and resource specific parameters such as batch sizes, and setup and cleanup times. The collaborative planning concept allows all the plants to work simultaneously as partners in a supply chain resulting in higher transparency, greater flexibility, and reduced response time as a whole. The user interface supports monitoring production schedules graphically and provides custom-built utilities for manual changes to the production schedule, investigation of various what-if scenarios, and marketing queries. RID="*" ID="*" The authors would like to thank Hans-Otto Günther and Roland Heilmann for helpful comments on draft versions of this paper.     

The effects of adverse condition warning system characteristics on driver performance: an investigation of alarm signal type and threshold level

This study addresses the issues concerning the design of adverse condition warning systems (ACWS). ACWS are designed to sense adverse road and weather conditions as well as system states that can negatively impact driving performance leading to skids or accidents, and alert drivers to these conditions. In this case, an ACWS was designed to sense when a car was likely to skid. A virtual-driving environment was used to test two levels of alarm sensitivity (low and high) and two types of auditory alarm signal (Binary ON/OFF and Graded) along with a no-alarm control group. Dependent measures reflected driver performance, response to the alarm signal and trust in the alerting system. Results indicated that participants had fewer skids in the low sensitivity and graded alarm signal condition compared to some other alerting system configurations. Participants in the graded alarm signal condition also had a greater degree of lateral control over the vehicle. Additionally, trust was found to be lower for the high vs. low sensitivity alarm condition, indicating a reduction in trust when the alerting system activated more often, perhaps because participants did not feel the system was accurately reflecting a dangerous condition. This simulator-based research emphasizes the fact that while ACWS may provide an advantage in terms of vehicle control, characteristics of both the alerting signal and system configuration should be considered.     

Spontaneous intracranial hypotension: report of four cases and review of the literature

Spontaneous intracranial hypotension is an unusual syndrome of postural headache and low cerebrospinal fluid pressure without an established cause. We present four cases, analyze those previously reported in the literature, examine the MRI, CT, angiographic and cisternographic finding and discuss the clinical picture, proposed pathophysiologic mechanisms and potential treatment.     

Operative fluoroscopy in hand and upper limb surgery. One hundred cases

We reviewed the use of a low radiation portable fluoroscopy unit in 100 patients. The most common indication was closed reduction of distal radial fractures. Fracture and joint stability were assessed on the real-time monitor and stored on videotape. Static images were stored on thermographic paper. Fluoroscopically guided joint injections and localization of implants, foreign bodies and bone tumours were performed. Fluoroscopy is a useful adjunct to arthroscopic assisted fracture reduction and other arthroscopic procedures such as distal ulnar resection. These new generation units produce superior resolution images, are easy to manoeuvre and do not require a radiographer.