鞍钢1780mm热轧生产线"三电"工程施工概述

概述了鞍钢1780mm生产线技术改造工程中供电、传动及自动控制系统的构成、安装及调试技术要点,以及技术经济效果评述,可供同类工程施工参考.     

乙炔在磁稳定床中的选择性加氢研究

 制备了一种磁性Pd/Al₂O₃催化剂，采用磁稳定床考察了活性组分负载量、反应条件及CO浓度对乙炔加氢反应性能的影响。结果表明，当反应温度80℃、反应压力1.5MPa、空速9000h－1、磁场强度（H）25kA/m时，乙炔转化率为100％，乙烯选择性可达81％，具有优良的乙炔加氢活性和乙烯选择性，优于相同反应条件下的进口催化剂；250h稳定性实验结果表明，磁性Pd/Al2O3催化剂具有良好的初活性和乙烯选择性，催化剂性能稳定。     

路43-P1水平井高密度钻井液难点技术的解决

路43-P1井是冀中坳陷饶阳凹陷留西油田路43断块施工难度较大的一口水平井。该井上部地层泥岩吸水膨胀造浆性强；下部地层局部存在异常高温，泥岩水敏性强，易吸水膨胀，造成地层坍塌。采用高密度钻井液钻井满足了井下要求，避免了井漏，减少了复杂情况的发生，缩短了建井周期；解决了深部定向、井温高、地层压力大、地层易垮塌的问题，顺利地完成了钻井目的。     

浮体门设计的探索与实践

水电站泄水道破坏修复工程,是一项风险高、难度大、前景广阔的系统工程。刘家峡水电站泄水道2号孔破坏修复的关键,是采用人工深水软导向浮体闸门封堵孔口,形成门后洞内旱地施工条件;龚嘴水电站10号冲砂底孔破坏修复的关键,增设浮体闸门采用自动潜行式浮体闸门封堵孔口,形成门后洞内旱地施工条件;哈萨克斯坦CHARDARA水电站SYNAS项目泄水底孔修复的关键,采用分次降水安装浮体闸门侧支承的方法,挡住引水发电机组的下游尾水,在泄水道进口检修门和流道出口之间形成门旱地施工。此3项泄水道修复工程在行业内没有先例,难度很大。整体方案具有创新性,并且均已高质量竣工并投入正常运行。     

A Subcarriers Allocation Scheme for Cognitive Radio Systems Based on Multi-Carrier Modulation

Cognitive radio (CR) is a dynamic spectrum access technology as a solution to spectrum under-utilization problem in some licensed bands. Operating over an exceedingly wide spectrum, CR systems usually adopt multi-carrier modulation (MCM) to implement flexible channelization. Consequently, efficient channel allocation scheme becomes extremely important to an MCM based CR (MCM-CR) system. In this paper, a maximum likelihood detection model is developed to detect the presence and locations of licensed users (LUs) signals in the frequency domain. Performance of the detection model, including the optimal detection region, detection probability and false alarm probability, is analyzed. A one-order two-state Markovian chain model is proposed to predict channel status information. In particular, a novel subcarrier allocation scheme for MCM-CR systems is proposed, taking into account the confidence of channel estimation, quality of services (QoS) of rental users (RUs) and throughput. To validate the analytical results, simulations have been conducted to show effectiveness of the proposed scheme.     

坨五站中间乳化层快速增长原因及治理方案

胜利采油厂坨五站高含水(95％)原油化学预脱水中，二级沉降罐内油水相之间的中间乳化层增长迅速，引起了一系列问题。现场调查和大量室内测试结果表明，产生这一现象的原因有：油溶性破乳剂WD-1加入点不合理。有2／3的含水原油在通过油水分离器之后才与破乳剂混合；二级沉降罐进油口伸入油相内，油流的冲击达不到中间层；WD-1对坨五站混合原油中的稠油破乳脱水性能欠佳，不能适应坨五站混合原油组成和含水的变化。针对上述各种原因筛选出了性能更好的一种破乳剂1916。根据确定的几种原因采取了相应的措施：将破乳剂加入点改在3个并联油水分离器之前；将二级沉降罐的进油口移到水相内；改用筛选出的破乳剂1916，结果使中间乳化层的增长受到了抑制。图2表4参2。     

Hydriding and Dehydriding Characteristics of Mechanically Alloyed LaMg_(17) Ni Composite Material

Magnesiumandmagnesiumalloyshavebeenin vestigatedashydrogenstoragematerialsforseveralde cadesbecausefarmorehydrogenbyweightcanbestoredinthemthaninmostoftheothercurrentlyknownhydrogenstoragealloys .Moreover ,thehighnaturalabundanceofMg ,itslightmassandenviron mentalcompatibilitypotentiallymakemagnesiumoneofthemostprospectivecandidatesforfuturehydrogenstoragematerials .Unfortunately ,thepracticalappli cationofMganditsalloyshasbeenlimitedonlytocertainstoragedevicebecauseoftheirpoorhydriding dehydr…     

基于加载算法的室内无线信道OFDM接收机的性能

本文研究了无线局域网中使信号频谱得到优化的一种简单OFDM子载波加载算法。此算法基于边缘自适应（Margin Adaptive）加载准则及其在室内无线信道上的性能。     

Freestanding Alumina Membrane by Double-Layer Anodization

A novel method has been developed for fabricating full or partial freestanding anodic alumina. In our method a sacrificial metal layer is introduced between an Al film and a Si₃N₄ substrate. A freestanding alumina film at wafer scale is successfully achieved by anodizing the double metal layer, during which the alumina is spontaneously stripped off the Si₃N₄ substrate due to the anodic oxidation of the sacrificial layer. The barrier oxide of the alumina film is effectively removed either by H₃PO₄ dissolution or by CF₄ reactive ion etching. The freestanding alumina film is utilized as a contact mask to transfer its nanoporous pattern to a Si substrate. By patterning the sacrificial metal layer with contact lithography, a partial freestanding alumina film is successfully achieved on the silicon chip, producing a unique micro/nanofluidic channel. Compared with previous techniques, the method reported here is advantageous for its simplicity and flexibility     

A Microfluidic Device to Acquire Gaseous Samples Via Surface Tension Held Gas-Liquid Interface

We present a relatively simple and effective method for acquiring gaseous samples into microfluidic channels. Hydrophobic polymers are photopatterned on hydrophilic substrates. Due to surface tension, aqueous liquid is confined by the hydrophobic polymers, but not completely blocked by a physical wall, thus allowing an interface for gas-liquid interaction. Here, the mechanism is demonstrated by using hydrophobic (poly)iso-bornyl acrylate polymer patterns on hydrophilic glass substrates, and through a Nessler's reagent-ammonia reaction that exhibits changes in color and electrical resistance.