新型阳离子聚丙烯酰胺微粒的研究 Ⅱ.含PEO支链阳离子聚丙烯酰胺微粒的絮凝性能

以丙烯酰胺、丙烯酰氧基乙基三甲基氯化铵、聚氧乙烯大单体和N ,N’ -亚甲基双丙烯酰胺为单体 ,进行四元反相微乳液共聚合 ,制备出新型含PEO支链的阳离子微粒絮凝剂。然后用该微粒絮凝剂分别对针叶木纸浆和特种纸白水进行了助留和絮凝性能的研究 ,结果表明 ,本新型微粒具有能单独使用、絮凝效果好和抗剪切性强等优点。     

Wave-attenuation estimation in fluid-filled steel pipes: The first longitudinal guided wave mode

Attenuations of the first (or fundamental) longitudinal guided wave modes propagating in liquid-filled steel pipes are numerically investigated. Several filling liquids transported by the steel pipe are considered in the investigation. In the numerical modeling stage, a sink is considered for abandoning standing wave modes caused by the internal liquids; hence, the attenuation dispersion curves become simpler. From the attenuation dispersion curves, two specific attenuation values corresponding to 1 MHz and 2.68 MHz are selected; then, the concept of parametric density is introduced to predict attenuation for a certain filling material. With this concept, it is possible to approximately calculate attenuation values without a complex numerical attenuation calculation. This investigation may provide fundamental data to inspectors using ultrasonic guided-wave techniques in the petrochemical industry and in the field of water supply, two branches of the economy that are always under pressure owing to the demand of increasing productivity and that are challenged owing to stricter environmental rules, thus necessitating promising, low-cost inspection techniques. The text was submitted by the authors in English.     

新型阳离子聚丙烯酰胺微粒的研究--含PEO支链阳离子聚丙烯酰胺微粒的合成、助留性能及作用机理

本文采用反相微乳液聚合的方法合成了丙烯酰胺(AM)/丙烯酰氧基乙基三甲基氯化铵(AD-AMQUAT)/聚氧乙烯大单体(PEO-A)/N,N'-亚甲基双丙烯酰胺(Bis)的四元共聚物微粒.研究了该微粒助留剂的结构与性能.这种微粒和纸纤维能够通过离子键和氢键作用显著地增强助留效果.     

YAG：Ce Phosphors for WLED via Nano-Pesudoboehmite Sol-Gel Route

The sub-micron sized YAG ： Ce phosphors were synthesized via a modified sol-gel method by peptizing nano-pesudoboehmite particulate. It is found that YAG phase from the dried gel powders appears at 1000 ℃ then the pure YAG phase exists at a relatively lower sintering temperature of 1400 ℃. The smaller sizes of phosphors in the ranges of 1 - 3 μm are obtained due to the contribution of seeding effects of nano-sized alumina particles to strengthen each step of the processes. Both the excitation and emission spectra of photoluminescence of the phosphor obtained at 1400 ℃ meet well with the spectroscopic requirements of the WLED phosphors.     

Thermo-acoustic instability in the horizontal Rijke tube

The instability curve of a Rijke tube system was obtained accurately by following different paths of heat power and flow-rate for three regions and by defining its locus from the criterion based on the measured sound pressure levels. The unstable limits in the region of flow-rate lower than that at the minimal power are compared with previous data. To observe the effect of turbulence on the unstable limits, inflow turbulence was introduced by placing a bundle of circular cylinders upstream of the heating part (50< Re_d< 700). The large-amplitude inflow fluctuation may delay the transition of the chamber acoustic mode to the unstable zone even at a sufficient power.     

6to4与ISATAP技术相结合的IPv6网络实现

在IPv4向IPv6过渡期间,多种过渡技术可以互相支持、互相组合使用,以达到互利互助。简要介绍了其中2种隧道技术:6to4技术和ISATAP技术,提出了1种基于两者结合的新型实验网络的实现方案。具体讨论了在Linux下如何组建这种新型实验网络平台,详细阐明了如何配置IPv6主机以及双栈路由器,为IPv4过渡到IPv6提供1个可行的方案。     

"JDS-音频化渣微机综合检测系统"的应用与效果

简要介绍“JDS-音频化渣微机综合检测系统”的工作原理和应用效果，证明使用该装置是提高炼钢操作水平的一条较好途径。     

板坯连铸机二切短流程生产线的开发和应用

3^#板坯连铸机二切工序一直不能正常工作，采用了在线切割工艺，根据切割条件和切割周期等参数，结合板坯连铸出坯线短、车间小的特点，确定二切机的位置在距一切终止点15m处。改进了清渣系统，采取了升降挡板和定尺板相结合的定尺方式，设定不同的辊道运输速度等措施，保证了二切设备的正常运行，实现了板坯的热送热装．     

Estimation of collapse moment for the wall-thinned pipe bends using fuzzy model identification

In this work, the collapse moment due to wall-thinned defects is estimated through fuzzy model identification. A subtractive clustering method is used as the basis of a fast and robust algorithm for identifying the fuzzy model. The fuzzy model is optimized by a genetic algorithm combined with a least squares method. The developed fuzzy model has been applied to the numerical data obtained from the finite element analysis. Principal component analysis is used to preprocess the input signals into the fuzzy model to reduce the sensitivity to the input change and the fuzzy model are trained by using the data set prepared for training (training data) and verified by using another data set different (independent) from the training data. Also, three fuzzy models are trained, respectively, for three data sets divided into the three classes of extrados, intrados, and crown defects, which is because they have different characteristics. The relative root mean square (RMS) errors of the estimated collapse moment are 0.5397% for the training data and 0.8673% for the test data. It is known from this result that the fuzzy models are sufficiently accurate to be used in the integrity evaluation of wall-thinned pipe bends and elbows.     

光纤温度传感器综述

本文阐述了温度传感器的概况和使用要求，详细地论述了目前国外各类光纤温度传感器的原理、结构、特点、技术水平和发展状况。