High voltage (>1kV) and high current gain (32) 4H-SiC power BJTs using Al-free ohmic contact to the base

This letter reports the design and fabrication of 4H-SiC bipolar junction transistors with both high voltage (>1kV) and high dc current gain (/spl beta/=32) at a collector current level of I/sub c/=3.83A (J/sub c/=319 A/cm/sup 2/). An Al-free base ohmic contact has been used which, when compared with BJTs fabricated with Al-based base contact, shows clearly improved blocking voltage. A specific on-resistance of 17 m/spl Omega//spl middot/cm/sup 2/ has been achieved for collector current densities up to 289 A/cm/sup 2/.     

Influence of Solution Composition on the Formation of Crystalline Scales

Scale formation is a difficulty encountered with water containing ions of sparingly soluble salts that can readily precipitate on heat transfer surfaces in evaporative concentration operations. Scale formation, hindering the heat transfer process, increases specific energy consumption and operating costs and causes frequent shut down of the evaporator for cleaning. The effects of changes in composition of the solution due to evaporation and CO₂ release on the formation of crystalline scales in seawater evaporators are studied. A model that predicts the CO₂ release is presented. The carbonate system in the salt solution on its whole flow path through the evaporator and the scaling (crystallization) tendency are described. Simulation results for different process configurations are shown and the differences are discussed, particularly with regard to the incrustation tendency.     

Design of radiation-emission measurements of an air-traffic surveillance radar

The current work presents the procedure of designing and carrying out measurements of radiation emission from an air-traffic surveillance radar. The system requirements are first given, and then the equipment used is described. The steps to determine the operating characteristics of the radar are specified in detail. The necessary methods for manual power measurements and calculations are next explained. Since the final measurement system was fully automated, its main features (topology, protocol of operation) are also given. Finally, some measurement results taken during the initial phase of system operation are presented and discussed.     

An adaptive Gaussian model for satellite image deblurring

The deconvolution of blurred and noisy satellite images is an ill-posed inverse problem, which can be regularized within a Bayesian context by using an a priori model of the reconstructed solution. Since real satellite data show spatially variant characteristics, we propose here to use an inhomogeneous model. We use the maximum likelihood estimator (MLE) to estimate its parameters and we show that the MLE computed on the corrupted image is not suitable for image deconvolution because it is not robust to noise. We then show that the estimation is correct only if it is made from the original image. Since this image is unknown, we need to compute an approximation of sufficiently good quality to provide useful estimation results. Such an approximation is provided by a wavelet-based deconvolution algorithm. Thus, a hybrid method is first used to estimate the space-variant parameters from this image and then to compute the regularized solution. The obtained results on high resolution satellite images simultaneously exhibit sharp edges, correctly restored textures, and a high SNR in homogeneous areas, since the proposed technique adapts to the local characteristics of the data.     

The Effect of Moisture Content on the Conversion of Ergosterol to Vitamin D in Shiitake Mushrooms

The distribution of ergosterol in different parts of shiitake mushrooms was studied in order to optimize the conversion of ergosterol to vitamin D₂ during drying. The effect of moisture on the conversion of ergosterol to vitamin D₂ was also investigated by adjusting the moisture content of fresh mushrooms to different levels in a large vacuum desiccator and subjecting them to UV irradiation at 290-320 nm wavelength, for 2 h. The moisture, ergosterol and vitamin D₂ contents were determined using standard procedures. It was found that the ergosterol content on a dry matter basis of fresh shiitake mushroom was highest in the gills (10.6 ± 0.99 mg/g DM), followed by the cap or pileus (5.34 ± 0.64 mg/g DM) and was least in the stalk or stipe (2.97 ± 0.56). The moisture content had a marked influence on the conversion of ergosterol to vitamin D₂, the best conversion taking place at a moisture content of about 70% on a wet basis.     

Linear birefringence studies on the ferroelastic phase transition in betaine borate crystal

Linear birefringence studies were performed for the BBO crystal in the temperature range of 120-300 K. The linear birefringence changes induced by the ferroelastic phase transition at about 145 K were analysed and the critical index β was determined. The layered ferroelastic domain structure with domain walls oriented along the c- and a-axis was observed on the b-plate.     

Theoretical Analysis of the Fiber Pullout and Pushout Tests

The fiber pullout and pushout tests have been analyzed to predict the load-displacement behavior in terms of fiber/matrix interface parameters. The effects of residual axial strain in the fiber and fiber surface topography were included. The residual axial strain was found to be a significant parameter. It is shown that the interface failure can be progressive or catastrophic. In the case of a progressive failure of the interface, the load-displacement curve is nonlinear. The portion of the curve from above the first nonlinearity to near the peak load can be predicted in terms of parameters of the interface, viz., the friction coefficient, the radial stress at the interface, the fracture toughness of the interface, and the residual axial strain in the fiber. Values for these parameters can be obtained from a single loaddeflection curve. The peak load and load drop, which are usually reported, are found not to be directly relatable to any interface property, since the length of the last portion of the fiber to debond is influenced by end effects and hence not easily predicted. However, for data which describe the peak load as a function of initial embedded length, that factor can be eliminated and the data reduced to yield the relevant interface parameters. In pullout, the peak and friction loads saturate with large specimen thickness. Catastrophic failure is favored when the debond initiation load is high or when residual stress is low. Finally, a methodology to extract interface parameters from experimental data is suggested.     

Synthesis and evaluation of hexafluorodimethylcarbinol functionalized polymers as microsensor coatings

Polystyrenes, polyacrylates, and poly(3,4-isoprenes) incorporating the hexafluorodimethylcarbinol functionality have been synthesized, characterized, and tested as microsensor coatings on a surface acoustic wave (SAW) device for dimethyl methylphosphonate (DMMP) vapor absorption sensitivity. The syntheses involved monomer functionalization and polymerization or hexafluoroacetone reaction with preformed polymer. All fluoroalcohol functionalized polymer coatings displayed sub parts per million level sensitivity with the slope of the absorption isotherm steepest at low DMMP concentrations. The order of sensitivity for the isomeric polystyrene fluoroalcohols (meta > para ? ortho) paralleled that of the relative free hydroxyl to hydrogen-bonded hydroxyl content. Strong hydrogen bonding between the fluoroalcohol polymers and DMMP vapor was observed by IR spectroscopy. Acylation of the fluoroalcohol group markedly reduced the DMMP sensitivity.