Crystal plasticity modeling of deformation and creep in polycrystalline Ti-6242

This paper develops an experimentally validated computational model based on crystal plasticity for the analysis of two-phase α/β Ti-6242 polycrystalline alloys. A rate-dependent elastic-crystal plasticity model is incorporated in this model to accommodate anisotropy in material behavior and tension-compression asymmetry inherent to this alloy. A combination of microtesting, orientation imaging microscopy, computational simulations, and minimization process, involving genetic algorithms, is implemented in this study for careful characterization and calibration of the material parameters. Size effects are considered in this analysis through a simple scaling process. A homogenized equivalent model of the primary α with transformed β colonies is developed for incorporation in the Ti-6242 FE model. The polycrystalline Ti-6242 computational model incorporates accurate phase volume fractions, as well as statistically equivalent orientation distributions to those observed in the orientation imaging microscopy scans. The effects of orientation, misorientations, and microtexture distributions are investigated through simulations by this computational model. The model is used to simulate constant strain rate and creep tests in compression and tension, and the results are compared with experiments. The effects of microstructure and creep-induced load-shedding on the localization of microstructural stresses and strains are studied for potential crack initiation criteria.     

A kinematic analysis of the modified flight telerobotic servicer manipulator system

A reverse analysis of a 6 degree of freedom (dof) subchain of a modified 7 dof flight telerobotic servicer (FTS) manipulator system is presented. The 6 dof subchain is designated as a TR-RT* chain. At the outset, it was considered that the reverse analysis would be similar to a TTT manipulator analyzed previously for which the third and fourth joints intersect at a finite point. This was not, however, the case and a sixteenth-degree tan-half-angle polynomial was derived for the TR-RT manipulator. The elimination procedure is interesting and much simpler than the procedures for the general case.     

Investigation of the thermal, mechanical, and fracture properties of alumina-epoxy composites

A combination of dynamic shear rheology, thermomechanical analysis (TMA), scanning electron microscopy (SEM), Near-Edge X-ray Absorption Fine Structure (NEXAFS), and fracture toughness testing was utilized to characterize the thermal, mechanical, chemical, and fracture properties of alumina (α-Al₂O₃)-filled epoxy resins as a function of average filler size, size distribution, particle shape, loading, and epoxy crosslink density. In general the cured properties of the filled composites were robust. Small changes in particle size, shape, and size distribution had little impact on the final properties. Resin crosslink density and filler loading were the most critical variables, causing changes in all properties. However, most applications could likely tolerate small changes in these variables also. SEM and NEXAFS characterization of the fracture surfaces revealed that the fracture occurs at the filler interface and the interfacial epoxy composition is similar to the bulk resin, indicating a weak epoxy-alumina interaction. These results are critical for implementation of particulate-filled polymer composites in practical applications because relaxed material specifications and handling procedures can be incorporated in production environments to improve efficiency.     

ON SCIENCE, ECONOMICS AND EDUCATION

In their public statements, politicians and leaders of mostdeveloped countries espouse the doctrine that the growth oftheir respective economies is highly dependent on innovationsresulting from scientific research and development. Many countriessupport science directly or indirectly using a variety of subsidies,grants, contracts, or other financial mechanisms. But, the lion'sshare of support for research and development is usually providedby industry. The statistic often quoted is the percentage ofgross domestic product     

An analysis of lighting energy savings and switching frequency for a daylit corridor under various indoor design illuminance levels

Visual comfort and electric lighting energy issues are essential criteria to justify daylighting schemes. The evaluation of energy efficiency due to daylight linked lighting control systems is best demonstrated by case studies. This paper presents field measurements on daylighting for a fully air-conditioned daylit corridor. Artificial lighting load, brightness of the fluorescent luminaires, daylight availability for various switching illuminance levels were systematically recorded and analyzed. The general features and characteristics of the findings including the number of switching operations and electric-lighting energy savings are presented and discussed. Daylighting theories, using cumulative frequency distribution of outdoor illuminance and regression models based on brightness of light output, outdoor illuminance and electric light power to estimate daylight-linked lighting control savings, have been developed and assessed. It has been found that data from both approaches show reasonably good agreements with measured results. The findings from this study provide some operational and energy information, which would be useful and applicable to other interior spaces with similar architectural designs.     

Microarchitectures for Managing Chip Revenues under Process Variations

As transistor feature sizes continue to shrink intothe sub-90nm range and beyond, the effects of process variationson critical path delay and chip yields have amplified. A commonconcept to remedy the effects of variation is speed-binning, bywhich chips from a single batch are rated by a discrete range offrequencies and sold at different prices. In this paper, we discussstrategies to modify the number of chips in different bins andhence enhance the profits obtained from them. Particularly, wepropose a scheme that introduces a small Substitute Cacheassociated with each cache way to replicate the data elementsthat will be stored in the high latency lines. Assuming a fixedpricing model, this method increases the revenue by as much as13.8% without any impact on the performance of the chips.     

Male honor and female fidelity: Implicit cultural scripts that perpetuate domestic violence.

Two studies explored how domestic violence may be implicitly or explicitly sanctioned and reinforced in cultures where honor is a salient organizing theme. Three general predictions were supported: (a) female infidelity damages a man's reputation, particularly in honor cultures; (b) this reputation can be partially restored through the use of violence; and (c) women in honor cultures are expected to remain loyal in the face of jealousy-related violence. Study 1 involved participants from Brazil (an honor culture) and the United States responding to written vignettes involving infidelity and violence in response to infidelity. Study 2 involved southern Anglo, Latino, and northern Anglo participants witnessing a "live" incident of aggression against a woman (actually a confederate) and subsequently interacting with her. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Prediction of the effects on dynamic response due to distributed structural modification with additional degrees of freedom

The aim of this study is to investigate means of efficiently assessing the effects of distributed structural modification on the dynamic properties of a complex structure. The dynamic properties of the modified structure can be determined by experimental testing or numerical simulation, both of which are complex, expensive and time-consuming. Assuming that the original dynamic characteristics are already established and that the modification is a relatively simple attachment, the modified dynamic properties may be determined numerically without solving the equations of motion of the full-modified structure. The frequency response functions (FRFs) of the modified structure can be computed by coupling the original FRFs and a delta dynamic stiffness matrix for the modification introduced. The validity of this approach is investigated by applying it to a cantilever beam to which a smaller beam is attached as modification. The original FRFs were obtained experimentally as well as numerically. The delta dynamic stiffness matrix was determined numerically by modeling the attachment and part of the original structure including the attachment points. The FRFs of the modified beam were then computed. Good agreement is obtained by comparing the results to the FRFs of the modified beam determined experimentally as well as by numerical modeling of the complete modified structure.     

Neutron Reflectometry Characterization of Interface Width between Sol-Gel Titanium Dioxide and Silicon Dioxide Thin Films

Neutron reflectometry (NR) was used to directly measure the interface width between a titanium dioxide and a silicon dioxide film deposited by sol-gel processing. In a bilayer heated to 450°C, NR measurements showed that the interface width is 0.8 nm. This width is the same as the roughness of a sol-gel silicon dioxide surface after the same heat treatment, suggesting no interdiffusion or mixing at the bilayer interface.