Effect of low-cycle fatigue on the hot ductility of plain carbon steel

In a continuous casting steelmaking operation, the surface of a slab is under a condition that can be characterized as high-temperature, low-cycle fatigue in which the tensile and compressive stress is repeatedly developed. For this reason, for the evaluation of the hot ductility of a slab, considering the fatigue deformation is more feasible before a tensile or compressive test. In this study, the effects of low-cycle fatigue on the hot ductility of steels with a carbon content of 0.06–0.8 wt.% are investigated at various temperatures. For a carbon content of 0.06%, there were no significant differences between the RA values from a simple tensile test and those from a tensile test after fatigue deformation. The tendency of ductility deterioration with fatigue deformation is evident in 0.1 %C steel, and is due to the deformation-induced ferrite film that forms around the prior austenite grain. Conversely, high carbon steel containing 0.8 %C did not show a recovery of hot ductility in a low temperature region, and the specimen on which the tensile was measured after fatigue showed a higher hot ductility in the low temperature region, which is thought to result from the pearlite refinement effects. As the results obtained in this work showed noticeable differences in the hot ductility of carbon steel through the test conditions, it is suggested that for more accurate data, fatigue deformation be adopted in which the temperature range in an unbending operation is determined in the steelmaking factory.     

Gate location design in injection molding of an automobile junction box with integral hinges

Polymers such as polypropylene or polyethylene offer a unique feature of producing an integral or living hinge for automobiles, which can flex over a million times without causing a failure. However, due to increased fluidity resistance at hinges during molding, several defects such as short shot or premature failure can occur with the improper selection of gate locations. In this paper, a design guideline was induced by investigating resin flow patterns depending on several gate positions obtained by numerical analyses of a simple strip with a hinge. The analyses of the simple strip part showed that the resin at the hinge did not flow until the other side of the strip was filled. Once the resin at the hinge did not flow for a long time enough to be solidified, defects such as short shots or hesitation marks formed. For a practical application of the design guideline determined, four gate systems for an automobile junction box were designed. It was found that the properly determined gate location leads to better resin flow and shorter hesitation time. Finally, injection molding tryouts using a mold that was designed by one of the proposed gate systems were conducted. The experiments showed that hinges without defects could be produced by using the designed gate location to assure the induced design guideline to be reasonable.     

Picture-Neutrosophic Trusted Safe Semi-Supervised Fuzzy Clustering for Noisy Data

Clustering is a crucial method for deciphering data structure and producing new information. Due to its significance in revealing fundamental connections between the human brain and events, it is essential to utilize clustering for cognitive research. Dealing with noisy data caused by inaccurate synthesis from several sources or misleading data production processes is one of the most intriguing clustering difficulties. Noisy data can lead to incorrect object recognition and inference. This research aims to innovate a novel clustering approach, named Picture-Neutrosophic Trusted Safe Semi-Supervised Fuzzy Clustering (PNTS3FCM), to solve the clustering problem with noisy data using neutral and refusal degrees in the definition of Picture Fuzzy Set (PFS) and Neutrosophic Set (NS). Our contribution is to propose a new optimization model with four essential components: clustering, outlier removal, safe semi-supervised fuzzy clustering and partitioning with labeled and unlabeled data. The effectiveness and flexibility of the proposed technique are estimated and compared with the state-of-art methods, standard Picture fuzzy clustering (FC-PFS) and Confidence-weighted safe semi-supervised clustering (CS3FCM) on benchmark UCI datasets. The experimental results show that our method is better at least 10/15 datasets than the compared methods in terms of clustering quality and computational time.     

Short packet communication in underlay cognitive network assisted by an intelligent reflecting surface

We propose short packet communication in an underlay cognitive radio network assisted by an intelligent reflecting surface (IRS) composed of multiple reconfigurable reflectors. This scheme, called the IRS protocol, operates in only one time slot (TS) using the IRS. The IRS adjusts its phases to give zero received cumulative phase at the secondary destination, thereby enhancing the end-to-end signal-to-noise ratio. The transmitting power of the secondary source is optimized to simultaneously satisfy the multi-interference constraints, hardware limitations, and performance improvement. Simulation and analysis results of the average block error rates (BLERs) show that the performance can be enhanced by installing more reconfigurable reflectors, increasing the blocklength, lowering the number of required primary receivers, or sending fewer information bits. Moreover, the proposed IRS protocol always outperforms underlay relaying protocols using two TSs for data transmission, and achieves the best average BLER at identical transmission distances between the secondary source and secondary destination. The theoretical analyses are confirmed by Monte Carlo simulations.     

Self-identification algorithm for zeolite-based thermal capacity gas sensor

Microsystem Technologies - We demonstrate a new operation mode of thermal gas sensor based on thermal capacity extraction with identification algorithm. The system is a silicon microstructure...     

Some peculiarities of electric discharge between a solid electrode and technical water

We present the results of experimental study of the electric discharge between metal electrodes of various geometry and technical water within the pressure range of 8 × 10³–10⁵ Pa at the saw-tooth voltage generator frequency, f = 40 MHz, and the interelectrode distance, l = 3–30 mm. We consider transfer of the streamer discharge into spark one depending on the geometry of the metal electrode and its material. We investigate the electrical characteristics of the discharge between the plate electrode and the technical water within a wide pressure range. The essential influence of the streamer discharge type on the ozone release within the investigated parameters range is discovered.     

Erratum to: Charge transfer in graphene/polymer interfaces for CO2 detection

Nano Research - The order of the authors in the original version of this article was unfortunately incorrect on the first page and the first page of the ESM. Instead of Myungwoo Son1, Yusin Pak1,...     

A Hemispherical Image Sensor Array Fabricated with Organic Photomemory Transistors

Hemispherical image sensors simplify lens designs, reduce optical aberrations, and improve image resolution for compact wide-field-of-view cameras. To achieve hemispherical image sensors, organic materials are promising candidates due to the following advantages: tunability of optoelectronic/spectral response and low-temperature low-cost processes. Here, a photolithographic process is developed to prepare a hemispherical image sensor array using organic thin film photomemory transistors with a density of 308 pixels per square centimeter. This design includes only one photomemory transistor as a single active pixel, in contrast to the conventional pixel architecture, consisting of select/readout/reset transistors and a photodiode. The organic photomemory transistor, comprising light-sensitive organic semiconductor and charge-trapping dielectric, is able to achieve a linear photoresponse (light intensity range, from 1 to 50 W m⁻²), along with a responsivity as high as 1.6 A W⁻¹ (wavelength = 465 nm) for a dark current of 0.24 A m⁻² (drain voltage = −1.5 V). These observed values represent the best responsivity for similar dark currents among all the reported hemispherical image sensor arrays to date. A transfer method was further developed that does not damage organic materials for hemispherical organic photomemory transistor arrays. These developed techniques are scalable and are amenable for other high-resolution 3D organic semiconductor devices.     

Double Auction-based Scheduling of Scientific Applications in Distributed Grid and Cloud Environments

Economy models have long been considered as a promising complement to the classical distributed resource management not only due of their dynamic and decentralized nature, but also because the concept of financial valuation of resources and services is an inherent part of any such model. In its broadest sense, scheduling of scientific applications in distributed Grid and Cloud environments can be regarded as a market-based negotiation between a scheduling service optimizing user-centric objectives (execution time, budget), and a resource manager optimizing provider-centric metrics (resource utilization, income, job throughput). In this paper, we propose a new instantiation of the negotiation protocol between the scheduler and resource manager using a market-based Continuous Double Auction (CDA) model. We analyze different scheduling strategies that can be applied and identify general strategic patterns that can lead to a fast and cheap work ow execution. In the experimental study, we demonstrate that under certain circumstances one can benefit by applying an aggressive scheduling strategy.