Analysis of heregulin symmetry by weighted evolutionary tracing

Heregulins are members of the protein family of EGF-like growthand differentiation factors. The primary cell-surface targetsof heregulins are heterodimers of the EGF-receptor homolog HER2with either HER3 or HER4. We used a weighted evolutionary traceanalysis to identify structural features that distinguish theEGF-like domain (hrg) of heregulins from other members of theEGF family. In this analysis, each amino acid sequence is weightedaccording to its uniqueness and the variability in each positionis assigned by an amino acid substitution matrix. Conservedresidues in heregulin that are variable in other EGF-like domainsare considered possible specificity-conferring residues. Thisanalysis identifies two clusters of residues at the foot ofthe boot-shaped hrg domain. The residues in one cluster arerecruited from the N-terminus; those in the other are from the-loop region and show a weak sequence similarity to the N-terminalresidues at the opposite side of the boot. The remaining residueswith high conservation scores distribute themselves into thesetwo distinct surfaces on hrg. This pseudo-twofold symmetry andthe presence of two distinct interfaces may reflect the preferenceof hrg for heterodimeric versus homodimeric HER complexes.     

Dense silicon carbonitride ceramics by pyrolysis of cross-linked and warm pressed polysilazane powders

This study reports on the pyrolysis and densifaction behavior of cross-linked poly(hydridomethylsilazane) powders. The influence of the cross-linking procedure such as temperature and annealing time of the polymer powders on the compaction behavior under cold and warm pressing conditions is discussed. The degree of cross-linking is determined by thermal mechanical analysis (TMA). In addition to particle sliding which is assumed to be the compaction mechanism obtained by cold-pressing, the polymer powder consolidates by plastic deformation applying warm-pressing. A continuous 3-dimensional polysilazane network is formed after a dwelling time under these conditions. Pyrolysis of the cross-linked and compacted polysilazane powder in argon at 1100°C gives crack-free amorphous silicon carbonitride Si_3+xC_x+yN₄ with compositions ranging from x=1·47 and y=0·88 for cold pressed samples to x=1·47 and y=1·86 for warm pressed materials. The residual open porosity is significantly reduced from 10–15 vol% in the cold pressed specimens to 1·3–5 vol% by the warm pressing procedure. The weight loss during pyrolysis between room temperature and 1300°C is about 5 wt% lower than that for cold pressed specimens. This result is explained by a reduced methane evolution during the polymer-to-ceramic conversion and is in accordance with the enhanced carbon content of the warm pressed material.     

Detecting landscape forms using Fourier transformation and singular value decomposition (SVD)

Landscape structure is a main determinant of ecological landscape potentials. The basic differentiation of relief into depressions and elevations at deliberately chosen scales can be managed comfortably by the Fourier transformation. The automated extraction of these structures from an elevation map using Fourier transformation or singular value decomposition can help to overcome complicated and errorprone procedures based on the determination of numerical structure parameters such as slope and aspect. The combination of automated extraction methods and moving window technology can lead to further, more integrated insights related to complex landscape patterns.     

Simulation based analysis of secondary effects on solder fatigue

Secondary effects on thermal fatigue of solder joints, which frequently have been neglected, were studied by means of the finite element method (FEM). Based on a semi-empirical approach to predict fatigue life by evaluating the cyclic accumulated equivalent creep strain or energy density, effects of organic boards intrinsic properties on solder joint fatigue were investigated. Aspects of more realistic FR-4 board modelling were studied, in particular concerning its in-plane anisotropy and intrinsic warpage behaviour. Intrinsic board warpage was measured on test board level as well as for boards from series production. High intrinsic warpage was in particular found for several test boards. The effects for the worst case scenario observed so far were analysed for both first level and second level interconnects. The change in predicted fatigue life varied between 30% and 500%, the latter most critical effects were found at large QFN components. Another secondary effect studied was to include the frequently neglected interfacial intermetallics into FEM. It turned out that for components with relatively large standoff like LFBGAs the effects were actually negligible, but for the highly miniaturized components like chip resistors CR0201 they are the decisive factor.     

Antarctic springtime depletion of atmospheric mercury

Unlike other heavy metals that are inherently associated with atmospheric aerosols, mercury in ambient air exists predominantly in the gaseous elemental form. Because of its prolonged atmospheric residence time, elemental mercury vapor is distributed on a global scale. Recently, Canadian researchers have discovered that total gaseous mercury levels in the lower tropospheric boundary layer in the Canadian Arctic are often significantly depleted during the months after polar sunrise. A possible explanation may involve oxidation of elemental mercury, followed by adsorption and deposition of the oxidized form, leading to an increased input of atmospheric mercury into the Arctic ecosystem. Here we present the first continuous high-time-resolution measurements of total gaseous mercury in the Antarctic covering a 12-month period between January 2000 and January 2001 at the German Antarctic research station Neumayer (70 degrees 39' S, 8 degrees 15' W). We report that mercury depletion events also occur in the Antarctic after polar sunrise and compare our measurements with a data setfrom Alert, Nunavut, Canada. We also present indications that BrO radicals and ozone play a key role in the boundary-layer chemistry during springtime mercury depletion events in the Antarctic troposphere.     

Comparison of analysis methods for package-induced stresses on moulded Hall sensors

Due to the piezoresistive and the piezo-Hall effect in semiconductor materials, Hall sensors show a strong temperature dependency and also a drift when subjected to temperature cycles Manic et al. (2000). Four factors mainly influence the mechanical stress in the sensitive layer. These are the geometry of the device, the differences of the coefficients of thermal expansion of the package materials, the temperature-dependent material properties and the time-dependent, viscous material properties. The objective of this investigation was to determine the mechanical stress in a moulded Hall sensor during the packaging process by finite-element simulation in comparison to experimental methods. It is shown that after each process-step the mechanical stress in the sensitive layer changes over time depending on the absolute value and the rate of the temperature change. Measurements of the inverse bending radius of glued and moulded chips show good agreement to the simulations.     

Entwicklung rechtssicherer Web-Anwendungen

A broad variety of juridical requirements has to be considered during the development of Web-applications. Disregard of these requirements holds severe financial dangers. A complete compilation of juridical requirements is complicated due to the multitude of juridical areas and the variety of Web-applications. Therefore, a development-driven juridical framework is suggested. From a software engineering point of view it is crucial to capture requirements at an early stage of development in order to avoid much higher costs at a later time. Thus, specialized conceptual modelling methods are examined with regard to their capability to model juridical requirements. A lack of methodical support is identified which is addressed by a systematic adaption and extension of the eW3DT method.