Accelerated multi-contrast high isotropic resolution 3D intracranial vessel wall MRI using a tailored k-space undersampling and partially parallel reconstruction strategy

Objective

To develop a 3D multi-contrast IVW protocol with 0.5-mm isotropic resolution and a scan time of 5 min per sequence.

Materials and methods

Pre-contrast T1w VISTA, DANTE prepared PDw VISTA, SNAP, and post-contrast T1w VISTA were accelerated using cartesian undersampling with target ordering method (CUSTOM) and self-supporting tailored k-space estimation for parallel imaging reconstruction (STEP). CUSTOM + STEP IVW was compared to full-sample IVW, SENSE-accelerated IVW, and CUSTOM + zero-filled Fourier reconstruction in normal volunteers and subjects with intracranial atherosclerotic disease (ICAD). Image quality, vessel delineation, CSF suppression, and blood suppression were compared.

Results

CUSTOM + STEP vessel wall delineation was comparable to full-sample IVW and better than SENSE IVW for vessel wall delineation on T1w VISTA and luminal contrast on SNAP. Average image quality and wall depiction were significantly improved using STEP reconstruction compared with zero-filled Fourier reconstruction, with no significant difference in CSF or blood suppression.

Conclusions

CUSTOM + STEP allowed multi-contrast 3D 0.5-mm isotropic IVW within 30 min. Although some quantitative and qualitative scores for CUSTOM − STEP were lower than fully sampled IVW, CUSTOM + STEP provided comparable vessel wall delineation as full-sample IVW and was superior to SENSE. CUSTOM + STEP IVW was well tolerated by patients and showed good delineation of ICAD plaque.

     

Uncertainty of Analytic Measurements: Classical and New Approaches to Estimation

Measurement Techniques - A comparative analysis of the results of estimation of measurement uncertainty is conducted. The results are obtained by a method described in the Handbook on the...     

Microstrip Spurious-Coupling Band-Pass Filters with Quarter-Wavelength and Π-Shaped Resonators

Journal of Communications Technology and Electronics - Microstrip band-pass filters (BPFs) containing quarter-wavelength resonators and a Π-shaped half-wavelength resonator placed next to each...     

Characterization of Aluminum Foam Impact Response

Strength of Materials - The paper addresses the investigation of high-strain rate compressive behavior of Al foams subjected to impact at the intermediate striking velocity ranged from 40 to...     

Separation of hematite from banded hematite jasper (BHJ) by magnetic coating

The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that besides hematite and goethite,jasper, a microcrystalline form of quartzite, is the major impurity associated with this ore. Beneficiation by conventional magnetic separation technique could yield a magnetic concentrate containing 60.8% Fe with 51% Fe recovery. In order to enhance the recovery of the iron oxide minerals, fine magnetite, colloidal magnetite and oleate colloidal magnetite were used as the coating material. When subjected to magnetic separation, the coated ore produces an iron concentrate containing 60.2% Fe with an enhanced recovery of56%. The AFM studies indicate that the coagulation of hematite particles with the oleate colloidal magnetite facilitates the higher recovery of iron particles from the low grade BHJ iron ore under appropriate conditions.     

Production technology for low-carbon,low-sulfur boron steel

A technology for slag formation in the ladle–furnace unit is considered; the slag is based on the CaO–SiO₂–MgO–Al₂O₃–B₂O₃ system. This technology permits both microalloying of the steel with boron (reduced from the oxide phase) and desulfurization of the steel. The resulting boron content in the steel is 0.001–0.008%; the sulfur content in low-alloy steel and pipe steel is low (0.004–0.010%); and the consumption of manganese ferroalloys is reduced to 0.5 kg/t for 08кп steel and 1.4 kg/t for 09Г2C steel. In addition, the proposed technology increases the strength of the rolled steel, without loss in its plasticity; and reduces the environmental impact thanks to the replacement of fluorspar by colemanite.