A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

New ceramer high optical abrasion resistant transparent coating materials based on functionalized melamine and a tris(m-aminophenyl)phosphine oxide compound

Summary The synthesis of new high optical abrasion resistance coating materials has been undertaken by functionalizing melamine and tris(m-aminophenyl)phosphine oxide with a triethoxysilane containing reagent. These highly functionalized compounds have been used for coating a bis-phenol-A polycarbonate substrate by the sol-gel method. Preliminary data shows the abrasion resistance of the polymer substrate is considerably improved when it is coated by these optically clear materials.     

Experience in High-Temperature Thermomechanical Treatment with Helical Reduction in the Production of Axisymmetric Parts

Metal Science and Heat Treatment -     

Use of166mHo for calibration of gamma-ray spectrometers with semiconductor detectors

Translated from Atomnaya Énergiya, Vol. 67, No. 3, pp. 215–216, September, 1989.     

The effects of pressure on the isothermal fluid behavior of bituminous coals

An investigation into the effects of pressure (helium gas) on the isothermal fluid behavior includes: (1) the effect of pressure on the rate of melting and coking as evidenced by the rate constants k(melt) and k(coke); (2) the effect of pressure on the energies of activation of melting and coking; (3) the effects of pressure on the characteristic times; (4) the effects of pressure on the maximum isothermal fluidity. Results from the effects of pressure on k(melt) revealed that it was generally the high total sulfur, low nitrogen, low reactives/mineral matter ratio, medium rank coals which show the greatest increase in k(melt), whereas the highest rank coals show the least decrease in k(coke). The energies of activation of melting and coking were not significantly affected by pressure. The investigation also reveals increases or decreases in the respective times of softening, maximum fluidity, resolidification and total time of fluid behavior under isothermal pressurized conditions. There appears the possibility that these shifts may be rank dependent. Additionally, the lower rank coals show the largest relative increase in their fluidities when subjected to pressure. Empirical relationships were derived in order to quantitatively predict the maximum isothermal fluidity for most (fluid) coals at a given pressure.     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

Measurement of the delayed-neutron yields in the fission of233U,236U,237Np,240Pu,and241Pu by neutrons from the spectrum of a fast reactor

Translated from Atomnaya Énergiya, Vol. 66, No. 2, pp. 100–103, February, 1989.