Long distance fiber-optic transmission of C-band microwave signals to and from a satellite antenna

We demonstrate here the use of high-speed semiconductor lasers and detectors with low loss optical fiber for the transmission of the 500-MHz C-band microwave signal spectrum to and from a satellite antenna. The optical system has low attenuation and large band, width, so the microwave signals can be transmitted directly at the microwave frequency (4 or 6 GHz) over 20 km of fiber without regeneration or qualization. The optical system introduces ≈ 1 dB or less of degradation for both low spectral density QPSK signals and high spectral density FM video signals present in typical satellite transmission systems. For the video signals, the signal to noise after AM conversion was reduced from 56 to 55 dB. The microwave drive level to the laser must be significantly larger (typically > -10 dBm) than the intensity noise of the laser, yet small enough (typically < 10 dBm) to reduce the intermodulation distortion signals to an acceptable level. The laser bias current must be several times threshold so that the resonance frequency is beyond the frequency band of interest (4-6 GHz in this case). A flat modulation response is then obtained, and the intensity noise and intermodulation levels are low.     

A Device for Measurements of Dielectric Characteristics of Liquid Crystalline Materials, Solid Substances, and Their Melts

The device developed allows one to measure the dielectric characteristics of solid substances and their melts at frequencies of 20–20000 Hz and in a wide temperature range of 20–250°C. The measured temperature dependencies of the dielectric permittivities of several molecular and liquid crystals (stilbene, diphenyl, naphthalene, cholesterylpelargonate, and 8OCB) are presented.     

Subkilohertz fluctuations and mode hopping in high-powergrating-stabilized 980-nm pumps

The behavior of fiber Bragg grating (FBG)-stabilized 980-nm pump lasers is experimentally and theoretically investigated. The subkilohertz noise in the emitted power is related to the coexistence and oscillation between coherence collapsed state and narrow linewidth single-mode (SM) operation. These findings are theoretically discussed by using a multimode time-domain model that accounts for spatial harmonics and includes nonlinear gain. One additional result is an indication that kinks in the L-I curve can be explained by nonlinear mode competition     

RALOC4 code validation against measured data at Ignalina NPP during single Main Safety Valve opening

Although RALOC4 code is validated against many experiments with regard to Western Nuclear Power Plants (NPPs) the code validation problem for the Accident Localization System (ALS) of Ignalina NPP modeling is of special importance because the condensing pools at NPP with RBMK-1500 differ from the pressure suppression systems installed in NPPs with German BWR. The response of Ignalina NPP ALS to the unintentional opening of single Main Safety Valve, which occurred in 1998, is analyzed by employing code RALOC4. The results of post-event calculations compared with the measured data available after the event. The performed analysis showed that RALOC4 code could be applied for the simulation of Ignalina NPP ALS. Nevertheless, the spray modeling in RALOC4 should be improved allowing the simulation of sprays in NON_EQUILIBRIUM zone model and to consider the diameter of water droplet diameter and height of droplet fall.     

Integrated optical devices of InGaAsP/InP heterojunction phototransistor and inner stripe light-emitting diode

New integrated optical devices combining an InGaAsP/InP HPT and an inner-stripe LED are proposed and their fabrication processes are described. The device functions of light amplification, optical bistability, and optical switching are demonstrated in the 1-μm wavelength region.     

The design of robots and intelligent manipulators using modern composite materials

The operating speed and endpoint positional accuracy of existing industrial manipulators are limited by the inertial and stiffness characteristics of the articulating members of the robot's mechanical linkage. This limitation may be overcome by developing members having high structural stiffness and strength with low mass, and this has been recognized for some time. These characteristics can be obtained by fabricating the moving members of manipulators in fiber reinforced composite materials. In order to establish a basis for the dynamic analysis of robots fabricated in viscoelastic composites, a variational theorem is developed herein. A preliminary comparative study is then undertaken for manipulators manufactured in a graphite-epoxy composite material and also steel in order to demonstrate some of the advantages to be accrued from this proposed new design philosophy.     

A stability criterion for asynchronous multirate linear systems

A stability criterion is developed for linear, asynchronous multirate sampled-data systems. Such systems typically include a linear, time variant, continuous-time plant and several unsynchronized digital controllers. The analysis method uses a time-domain approach based on the closed-loop state transition matrix. The result is sufficient stability criterion which gives an objective measure of long-term and short-term stability. A simple example illustrates the method     

Context and lexical access: Implications of nonword interference for lexical ambiguity resolution.

To eliminate potential "backward" priming effects, S. Glucksberg et al (see record 1986-29080-001) introduced a variant of the cross-modal lexical priming task in which subjects made lexical decisions to nonword targets that were modeled on a word related to either the contextually biased or unbiased sense of an ambiguous word. Lexical decisions to nonwords were longer than controls only when the nonword was related to the contextually biased sense of the ambiguous word, leading Glucksberg et al to conclude that context does constrain lexical access and that the multiple access pattern observed in previous studies was probably an artifact of backward priming. We did not find nonword interference when the nonword targets used by Glucksberg et al were preceded by semantically related ambiguous or unambiguous word primes. However, we did replicate their sentence context results when the ambiguous words were removed from the sentences. We conclude that the interference obtained by Glucksberg et al is due to postlexical judgments of the congruence of the sentence context and the target, not to context constraining lexical access. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Smoothing the electromagnetic heating pattern in polymers

In the production of polymers, particles and fibers are often added for coloring and/or improvement of mechanical, electrical, and thermal properties. Carefully choosing the electrical properties and size of these additives can allow manipulation of the electrical properties of the composite so that the material can then be heated in both the electric and magnetic fields. Heating can be induced by fields at microwave frequences, where the electric and magnetic fields tend to be concentrated in different regions, or by fields that are quasistatic. These features add a degree of freedom in smoothing the total heating pattern. Models for predicting the electrical properties with the addition of particles or fibers are developed and verified experimentally. Engineering guidelines are established in choosing the electrical properties and size of the additives. Experimentally, a rectangular cavity at 2.45 GHz is used to heat a casting resin with a 5.7 micrometer aluminum powder additive, demonstrating the dramatic smoothing in the heating, pattern made possible by using these additives. Some examples are also suggested to indicate the use of this technique in quasistatic heating configurations.