Optimum Design of Sewage Sludge Consolidation Tanks

Consolidation is potentially the most cost-effective of all sludge treatment processes. However, traditional design procedures have been oversimplified such that the process has not generally been fully exploited.
The objective of this report is to summarize the Water Research Centre (WRc) procedure for sizing sewage sludge consolidation tanks, and explain the major design aspects which control the effective operation of the plant. The procedure provides a means of sizing tanks to consolidate any particular sewage sludge to any solids concentrations up to the maximum, and is applicable to both the batch and continuous operational modes. To obtain the predicted performance, the essential equipment such as the picket fence and control system, comprising a consolidation plant, must be suitably designed.     

The Use of Different Conveyance Calculations for Modelling Flows in a Compact Compound Channel

Flow measurements have been taken for steady and unsteady flows on a reach of a river having a compact compound channel. The 'single channel', 'divided channel' and 'lateral' distribution methods have been used to calculate conveyances for use in a one-dimensional unsteady flow model of the reach. Comparisons with measured flows show that the divided channel method and the lateral distribution method both underestimate floodplain flow depths. The lateral distribution method gives the closest accuracy in the relative depth range 0.15 ≤ Yr < 0.40. For large flow depths the single channel method becomes more accurate and slightly over-estimates flow depths.
The accuracy of unit width discharge distributions, calculated from the lateral distribution method are assessed by comparison with observed distributions for overbank flows.     

The Fate of Heavy Metals in Pilot-Plant Scale Upflow Sludge-Blanket Clarifiers

T he R emoval of heavy metals and aluminium residuals during upflow sludge-blanket clarification was investigated using a pilot-plant system. Pilot units treating predosed raw water on site were assessed for sludge-blanket formation and stabilization, and were found to produce clarified water of a comparable quality to the main works units after the start-up and stabilization periods were complete. The heavy metals Cr, Fe, Mn, and Ni were the only heavy metals detectable at the investigation site and these occurred at concentrations well below guidelines values for potable abstraction and supply.
Mean removals of Fe, Mn, Cr, and Ni were about 98, 89, 51, and 30 per cent respectively, during steady-state operation, and Fe, Mn, and Cr all displayed reduced removals during transient changes in surface load, whereas Ni removal appeared to be relatively independent. Aluminium residuals derived from the dosed alum coagulant also showed decreases in removal from about 83 per cent during steady-state operation to between 40 and 50 per cent during transient experiments.     

High-purity synthesis of scrolled mats of multi-walled carbon nanotubes using temperature modulation

Felt-like mats (6-7 μm thick) of multiwalled carbon nanotubes wrapped into scrolls have been synthesized by chemical vapor deposition from a toluene-ferrocene mixture using a temperature ramp from 680 °C to 550 °C in hydrogen-argon atmosphere. Thermogravimetric analysis reveals a very low catalyst content of ca. 1.25 wt% in the as-synthesized sample while, X-ray photo electron and Raman spectroscopies suggest the results matching with that of multiwalled carbon nanotubes. Considering, different time scales of various reactions and the diffusion of different reactants and products a tentative base growth mechanism has been proposed as per the available characterization data in conjunction with possible scrolling effects. Thermal expansion effects could explain a tentative mechanism for rolling action of sheets. Interestingly, electrical conductivity measurements as a function of temperature suggest a semiconducting behavior, despite being governed by different electron transport mechanisms with activation energies of 0.33 and 1.03 meV corresponding to two temperature ranges respectively. Cyclic voltammetry and electrochemical impedance analysis show a reversible redox behavior due to very low catalyst content and an irreversible etching of the Fe catalyst after acid treatment.     

Waveform classification and information extraction from LIDAR databy neural networks

Two different neural network schemes for the classification of light detection and ranging (LIDAR) waveforms for the LARSEN 500 airborne system and for extraction of ocean information are proposed. The first method employs a single layer of linear neurons for classification of waveforms into various clusters. Both unsupervised and supervised learning algorithms have been employed to demonstrate the spatial distribution of milt in near-shore waters. In the second method, a new multistage multilayer feedforward architecture is used for the classification of the waveforms and for the extraction of various types of ocean information. The stage I networks work in a parallel fashion and map the input waveforms to a set of characteristics. The networks in stage II use these characteristics to assign a signature number to the waveform or extract other information. Both the schemes are used with real-world data collected by the LARSEN 500 system. The paper concludes with experimental results and comparisons     

Selbstbestimmung und Selbstverständnis – Themenschwerpunkte im Umgang mit der Patientenverfügung

Ohne Zusammenfassung     

The Measurement of Plumbosolvency Propensity to Guide the Control of Lead in Tapwaters

A laboratory-scale lead-pipe rig has been developed into an accelerated test for 'plumbosolvency propensity'. High alkalinity water supplies from Anglian Water show either relatively high or low propensity characteristics which appear to be related to the form of the crystal deposit. These have been examined by scanning electron microscopy. The paper describes the uses of the test to (1) supplement random survey data, (2) investigate mixed waters, and (3) optimize orthophosphate dosing.