Transcutaneous measurement and spectrum analysis of heart wallvibrations

For the noninvasive diagnosis of heart disease based on the acoustic and elastic characteristics of the heart muscle, it is necessary to transcutaneously measure small vibration signals, including components with an amplitude of less than 100 μm, from various parts of the heart wall continuously for periods of more than several heartbeats in a wide frequency range up to 1 kHz. Such measurement, however, has not been realized by any ultrasonic diagnostic methods or systems to date. By introducing the constraint least-square approach, this paper proposes a new method for accurately tracking the movement of the heart wall based on both the phase and magnitude of the demodulated signal to determine the instantaneous position of the object so that the vibration velocity of the moving object can be accurately estimated. By this method, small vibrations of the heart wall with small amplitudes less than 100 μm on the motion resulting from a heartbeat with large amplitude of 10 mm can be successfully detected with sufficient reproducibility in the frequency range up to several hundred Hertz continuously for periods of about 10 heartbeats. The resultant small vibration is analyzed not only in the time domain, but also in the frequency domain. As confirmed by the preliminary experiments herein reported, the new method offers potential for research in acoustical diagnosis of heart disease     

Measurements ofPVTx properties of refrigerant mixture HFC-32+HFC-125 in the gaseous phase

The experimental 156PVTx properties of an important binary refrigerant mixture, HFC-32 (difluoromethane)+HFC-125 (pentafluorethane), have been measured for three compositions, i.e., 50, 60, and 80 wt% HFC-32, by a constant-mass-method coupled with expansion procedure in an extensive range of temperaturesT from 320 to 440 K, of pressuresP from 1.8 to 5.3 M Pa, and of densities p from 50 to 124 kg · m^–3. The experimental uncertainties of the present measurements are estimated to be within ±7 mK in temperature, ±2 kPa in pressure, ±0.2% in density and ±0.02 wt% of HFC-32. The sample purities are 99.998 wt% for HFC-32 and 99.99 wt% for HFC-125. Seventy-eight second and third virial coeflicients for temperatures from 320 to 440 K have been determined by the present measurements.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

Lipopolysaccharide primes human alveolar macrophages for enhanced release of superoxide anion and leukotriene B4: self-limitations of the priming response with protein synthesis

Human alveolar macrophages (AM) can produce potent reactive oxygen intermediates (ROI) and arachidonic acid metabolites (eicosanoids), which have important roles in host defense and the pathogenesis of some diseases of the lung. Bacterial lipopolysaccharide (LPS) is believed to cause profound lung injury and can prime mouse peritoneal macrophages for the enhanced secretion of ROI and eicosanoids. Therefore, we investigated the effect of LPS pretreatment on the ability of AM to release superoxide anions (O2-) and leukotriene B4 (LTB4). LPS can prime AM for the enhanced secretion of O2- and LTB4, regardless of whether they are derived from nonsmokers or smokers. Moreover, judging from the time-response characteristics, this priming for LTB4 release could be inhibited in the later stages of pretreatment, when the O2(-)-releasing capacity was enhanced. The priming inhibition was prevented, at least in part, by cycloheximide, but not by SOD and/or catalase. In addition, cycloheximide also inhibited the priming for O2- release. Hence, protein synthesis might be necessary for the priming for O2- release and for inhibiting the priming for LTB4 release. This phenomenon of self-limiting the priming response with LPS seems to be very important when we consider the high oxygen tension in the lungs and the many bacterial substances inspired into alveoli.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

An equation of state for 1,1-difluroethane (HFC 152a)

An equation of state for 1,1-difluoroethane (HFC 152a, CH₃CHF₂) has been developed on the basis of reliable experimental data including PVT, liquid C_p, and saturated-liquid-density data measured by our group. It is a non-dimensionalized virial equation whose functional form is the same as that originally developed for 1,1,1,2-tetrafluoroethane (HFC 134a) in our group. The effective range is for pressures up to 15 MPa, temperatures from 230 to 450 K, and densities to 1000 kg m⁻³. The equation represents reliable PVT measurements within ± 1% in pressure for the superheated vapour and supercritical fluid, while within ±0.5% in density for the compressed liquid. In addition, it should be noted that the equation represents the other essential thermodynamic properties including vapour pressures, saturated-liquid/ vapour densities, isobaric/isochoric specific heats and sound velocity in both the liquid and gaseous phase of HFC 152a.     

New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Air vent in water chamber and surface coating on liner slides concerning auxiliary cooling system for the high temperature engineering test reactor

Experimental study was made to confirm the validity of new designs of the auxiliary cooling system for the high temperature engineering test reactor (HTTR). First, it is necessary to vent residence air in outlet side of water chamber of the auxiliary heat exchanger for the HTTR. Accordingly, we have proposed to mount a proper bend duct in the outlet side of the water chamber. Air vent is done by difference between pressures at both ends of the bend duct caused by the forced water circulation using the water pumps. From flow tests, it was confirmed that it is capable of venting the air through the bend duct by circulating the water in maximum capacity of the water pumps. Second, it is essential to prevent seizure and excessive wear of the liner slides of the auxiliary concentric hot gas duct for the HTTR at a service temperature of 950°C. Therefore, we have put forward to coat titanium nitride (TiN) on the surface of the liner slides made of nickel-based superalloy Hastelloy XR using the thermochemical vapor deposition method. As a result of seizure and wear tests, it was confirmed that the TiN coating film of 3 μm on the surface of Hastelloy XR is sufficient.     

Boron removal by titanium addition in solidification refining of silicon with Si-Al melt

In order to effectively remove B from Si for its use in solar cells, a process involving B removal by solidification refining of Si using a Si-Al melt with Ti addition was investigated. For clarifying the effect of Ti addition on B removal from the Si-Al melt, TiB₂ solubilities in Si-64.6 at. pct Al melt at 1173 K and Si-60.0 at. pct Al melt at 1273 K were determined by measuring the equilibrium concentrations of B and Ti in the presence of TiB₂ precipitates. The small solubilities of TiB₂ in the Si-Al melt indicate the effective removal of B from the Si-Al melt by Ti addition. Further, solidification experiments of Si-Al alloys containing B by Ti addition were performed, and the effect of Ti addition on the solidification refining of Si with the Si-Al melt was successfully confirmed.     

Regenerating-mode low-speed operation of sensorless induction motor drive with adaptive observer

Speed estimation methods for sensorless induction motor drives can be divided into two groups. One is based on information about fundamental components of stator currents and voltages. The other is based on high-frequency components injection in stator voltages or currents. The latter may operate stably under zero frequency, which occurs in regenerating mode at low speeds. It, however, causes loss increasing and torque ripple. The former is difficult to operate under zero frequency. The authors propose a stable method categorized in the former group even in regenerating mode at low speeds. The proposed method is based on an adaptive flux observer. First, a new observer gain design is shown. Next, a method avoiding zero-frequency operation with controlling a rotor flux level is proposed.     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current–voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current–voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current–voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current–voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent Σ1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.