Performance of plate heat exchangers during calcium sulphate fouling — investigation with an in-line filter

The uncertainty about the fouling behaviour is one of the main reasons why plate and frame heat exchangers are not more widely installed in the chemical process industry and in power generating facilities. In the present investigation, the deposition of calcium sulphate in two different plate heat exchanger geometries was investigated. The deposition process was deliberately focused on crystallisation fouling through the installation of an in-line filter and the mode of preparation of the test solution. The investigated operating parameters were solution concentration, flow velocity, and bulk and surface temperatures. The heat exchangers were opened after each experiment to record the appearance and distribution of the deposits. The key result of this investigation is the strong correlation between the plate design and the tendency for deposit formation.     

Rapid Quantification of Low-Viscosity Acetyl-Triacylglycerols Using Electrospray Ionization Mass Spectrometry

Acetyl‐triacylglycerols (acetyl‐TAG) possess an sn‐3 acetate group, which confers useful chemical and physical properties to these unusual triacylglycerols (TAG). Current methods for quantification of acetyl‐TAG are time consuming and do not provide any information on the molecular species profile. Electrospray ionization mass spectrometry (ESI–MS)‐based methods can overcome these drawbacks. However, the ESI–MS signal intensity for TAG depends on the aliphatic chain length and unsaturation index of the molecule. Therefore response factors for different molecular species need to be determined before any quantification. The effects of the chain length and the number of double‐bonds of the sn‐1/2 acyl groups on the signal intensity for the neutral loss of short chain length sn‐3 groups were quantified using a series of synthesized sn‐3 specific structured TAG. The signal intensity for the neutral loss of the sn‐3 acyl group was found to negatively correlated with the aliphatic chain length and unsaturation index of the sn‐1/2 acyl groups. The signal intensity of the neutral loss of the sn‐3 acyl group was also negatively correlated with the size of that chain. Further, the position of the group undergoing neutral loss was also important, with the signal from an sn‐2 acyl group much lower than that from one located at sn‐3. Response factors obtained from these analyses were used to develop a method for the absolute quantification of acetyl‐TAG. The increased sensitivity of this ESI–MS‐based approach allowed successful quantification of acetyl‐TAG in various biological settings, including the products of in vitro enzyme activity assays.     

The Yeast ATF1 Acetyltransferase Efficiently Acetylates Insect Pheromone Alcohols: Implications for the Biological Production of Moth Pheromones

Many moth pheromones are composed of mixtures of acetates of long‐chain (≥10 carbon) fatty alcohols. Moth pheromone precursors such as fatty acids and fatty alcohols can be produced in yeast by the heterologous expression of genes involved in insect pheromone production. Acetyltransferases that subsequently catalyze the formation of acetates by transfer of the acetate unit from acetyl‐CoA to a fatty alcohol have been postulated in pheromone biosynthesis. However, so far no fatty alcohol acetyltransferases responsible for the production of straight chain alkyl acetate pheromone components in insects have been identified. In search for a non‐insect acetyltransferase alternative, we expressed a plant‐derived diacylglycerol acetyltransferase (EaDAcT) (EC 2.3.1.20) cloned from the seed of the burning bush (Euonymus alatus) in a yeast system. EaDAcT transformed various fatty alcohol insect pheromone precursors into acetates but we also found high background acetylation activities. Only one enzyme in yeast was shown to be responsible for the majority of that background activity, the acetyltransferase ATF1 (EC 2.3.1.84). We further investigated the usefulness of ATF1 for the conversion of moth pheromone alcohols into acetates in comparison with EaDAcT. Overexpression of ATF1 revealed that it was capable of acetylating these fatty alcohols with chain lengths from 10 to 18 carbons with up to 27‐ and 10‐fold higher in vivo and in vitro efficiency, respectively, compared to EaDAcT. The ATF1 enzyme thus has the potential to serve as the missing enzyme in the reconstruction of the biosynthetic pathway of insect acetate pheromones from precursor fatty acids in yeast.     

Transport of lithium through a supported liquid membrane of LIX54 and TOPO in kerosene

A mathematical transport model is developed for the extraction of lithium from dilute synthetic solution, simulating geothermal water, using a supported liquid membrane (SLM) of LIX54 (major component is -acetyl-m-dodecylacetophenone) and TOPO (tri-n-octylphosphine oxide) in kerosene. The model is based on fundamental mass transfer and kinetics mechanisms that account for all possible transport resistances. The model is solved numerically and is used to investigate the effect of various extraction conditions and membrane support characteristics. Reasonable agreement is found between the predicted and the experimental results reported in literature.     

Correlation between lattice strain and magnetic properties enhancement of nanocrystalline cobalt ferrite with controlled annealing

Journal of Materials Science: Materials in Electronics - Spinel cobalt ferrite (CoFe2O4) has been prepared using the citrate precursor sol–gel method. The synthesized samples have been...     

Raman Study of Hi-Nicalon-Fiber-Reinforced Celsian Composites: II, Residual Stress in Fibers

Band shifts in Raman spectra were used to assess, on a microscopic scale, the residual strain existing in Hi-Nicalon silicon carbide fibers reinforcing celsian-matrix composites. Uncoated as well as p-BN/SiC-coated and p-B(Si)N/SiC-coated Hi-Nicalon fibers were used as the reinforcements. We unambiguously conclude that the fibers were in a state of compressive residual stress. Quantitative determination of the residual stress was made possible by taking into account the heating induced by laser probing and by using a reference line, of fixed wavenumber. We found fiber compressive residual stress values between 110 and 960 MPa, depending on the fiber/matrix coating in the composite. A stress relaxation-like phenomenon was observed at the surface of p-BN/SiC-coated Hi-Nicalon fibers whereas the uncoated or p-B(Si)N/SiC-coated Hi-Nicalon fibers did not show any stress relaxation in the celsian-matrix composites.     

In-tube condensation of mixture of R134a and ester oil: empirical correlations

This paper presents a comparative study of the condensation heat transfer coefficients in a smooth tube when operating with pure refrigerant R134a and its mixture with lubricant Castrol “icematic sw”. The lubricant is synthetic polyol ester based oil commonly used in lubricating the compressors. Two concentrations of R134a-oil mixtures of 2% and 5% oil (by mass) were analysed for a range of saturation temperatures of refrigerant R134a between 35 °C and 45 °C. The mass flow rate of the refrigerant and the mixtures was carefully maintained at 1 g/s, with a vapour quality varying between 1.0 and 0. The effects of vapour quality, flow rate, saturation temperature and temperature difference between saturation and tube wall on the heat transfer coefficient are investigated by analysing the experimental data. The experimental results were then compared with predictions from earlier models [Int J Heat Mass Transfer (1979), 185; 6th Int Heat Transfer Congress 3 (1974) 309; Int J Refrig 18 (1995) 524; Trans ASME 120 (1998) 193]. Finally two new empirical models were developed to predict the two-phase condensation heat transfer coefficient for pure refrigerant R134a and a mixture of refrigerant R134a with Castrol “icematic sw”.     

Photophysical and charge-transporting properties of the copolymer SuperYellow

Conjugated copolymers are important materials for organic light-emitting diodes. Here, an investigation of the photophysical and charge-transporting properties of the prototypical poly(p-phenylene vinylene) based copolymer SuperYellow (SY) is reported. The study also investigated the effect of processing conditions by comparing the properties of spin-coated and solution-cast films. For both types of films, the results of time-resolved fluorescence and photoluminescence quantum yield measurements are similar. The high photoluminescence quantum yield of 60% and its independence of processing conditions shows the effectiveness of the bulky side groups in preventing concentration quenching of fluorescence. Time of flight measurements of charge mobility in both spin-coated and solution-cast films also showed similar results, with mobilities in the range 10^?6–10^?7 cm²/V s for both films. These results provide important information about a widely used copolymer and show that a good polymer light-emitting diode material can have low mobility.