Waves in periodic layered waveguides

Analytical expressions for EM-waves and evolutionary equations for the waves in geometric regular waveguides with layered nonstationary media are presented. A piecewise-homogeneous and periodic along the guide's axis medium is considered in detail. The analytical solution of the dispersion equation is invariant to both the guide's cross-section contour form and eigenwave type. The periodicity dispersion, particular resonances and an algorythm of the modeling application are discussed.     

90° SOI optical hybrid for Radio-over-fibre links

Radio-over- fibre (RoF) technology is receiving large attention due to its ability to provide simple antenna front ends, increased capacity and increased wireless access coverage. Coherently detected RoF systems would enable the information to be carried in both the amplitude and phase or in different states of the polarisation of the optical field. Additionally, the selectivity of coherent receiver is very well suited for access networks. We present a 90° optical hybrid built on a silicon-on-insulator planar light-wave circuit, which can be used as the optical front end of the digital coherent receiver in a digitised RoF link and will lead to reduced receiver footprint and cost. The optical hybrid circuit includes 2?×?2 and 4?×?4 multimode interference (MMI) splitters, in a polarisation diversity configuration. The simulation results at vacuum wavelength 1,550 nm show polarisation independence and phase errors between the ports of less than 0.03°. The properties of the prototyped 4?×?4 MMI were measured over a wide range of wavelengths. The 2?×?2 and 4?×?4 MMI showed nearly equal splitting ratios. Measurements of the relative phase relationship between the ports for Transverse Electric mode polarisation are shown to match the simulation results.     

Effect of mixed solvents on PCDTBT:PC70BM based solar cells

We investigated the effect of solvents on the morphology, charge transport and device performance of poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) and [6,6]-phenyl C71-butyric acid methyl ester (PC₇₀BM) based solar cells. To carry out this investigation, chloroform and 1,2-dichlorobenzene were chosen as good solvents of the two compounds. Films prepared with chloroform exhibit larger domains than those prepared with 1,2-dichlorobenzene and their size increases with the amount of PC₇₀BM. Fine tuning of the domain size was realized by using a solvent of mixed chloroform and 1,2-dichlorobenzene. At a mixing ratio of 50%:50%, a power conversion efficiency of 6.1% was achieved on PCDTBT:PC₇₀BM (1:3) devices with an active area of 1 cm², under air mass 1.5 global (AM 1.5 G) irradiation at 100 mW/cm².     

Two‐Dimensional Molybdenum Trioxide and Dichalcogenides

In the quest to discover the properties of planar semiconductors, two‐dimensional molybdenum trioxide and dichalcogenides have recently attracted a large amount of interest. This family, which includes molybdenum trioxide (MoO₃), disulphide (MoS₂), diselenide (MoSe₂) and ditelluride (MoTe₂), possesses many unique properties that make its compounds appealing for a wide range of applications. These properties can be thickness dependent and may be manipulated via a large number of physical and chemical processes. In this Feature Article, a comprehensive review is delivered of the fundamental properties, synthesis techniques and applications of layered and planar MoO₃, MoS₂, MoSe₂, and MoTe₂ along with their future prospects.     

Blocage par injection de modes sous- harmoniques d’un oscillateur utilisant une ligne à retard à ondes de surface

A nonlinear regeneration pulsed oscillator driven by a monochromatic source has been built. Subharmonics of the resonance carrier/modulation are measured with an accuracy of 10^-10 thanks to the use of a double beats measurement set-up. The multiscale analysis of frequency readings reveals a rich fine structure which is in agreement with the nonlinear topological approach of synchronized states.     

Enzymatic browning reactions in apple and apple products

This review examines the parameters of enzymatic browning in apple and apple products that is, phenolic compounds, polyphenoloxidases, and other factors (ascorbic acid and peroxidases), both qualitatively and quantitatively. Then the relationships between intensity of browning and the browning parameters are discussed, including a paragraph on the methods used for browning evaluation. Finally, the different methods for the control of browning are presented.     

Cassava retting: Optimisation of a traditional fermentation by an experimental research methodology

Retting, a spontaneous and traditional fermentation of cassava roots in Central Africa, was optimised in terms of time and the quality of the end-product. Optimal conditions were achieved by using an experimental research methodology. Temperature is the most influential factor, with an optimum of 34°C for quicker retting. The roots should be peeled and soaked in water immediately after harvesting to increase the quality of cassava foods. Inoculation of water with juice from a prior retting helps in cassava detoxification but has no influence on the time or the quality of foo-foo. Foo-foo samples had the most favourable organoleptic quality when an incubation temperature of between 28 and 37°C was used. Using optimal conditions, retting time was reduced 3-fold, and foo-foo of high and constant quality could be processed.     

Analysis and Test of Resistive-Open Defects in SRAM Pre-Charge Circuits

In this paper, we present an exhaustive study on the influence of resistive-open defects in pre-charge circuits of SRAM memories. In SRAM memories, the pre-charge circuits operate the pre-charge and equalization at a certain voltage level, in general Vdd, of all the couples of bit lines of the memory array. This action is essential in order to ensure correct read operations. We have analyzed the impact of resistive-opens placed in different locations of these circuits. Each defect studied in this paper disturbs the pre-charge circuit in a different way and for different resistive ranges, but the produced effect on the normal memory action is always the perturbation of the read operations. This faulty behavior can be modeled by Un-Restored Write Faults (URWFs) and Un-Restored Read Faults (URRFs), because there is an incorrect pre-charge/equalization of the bit lines after a write or read operation that disturbs the following read operation. In the last part of the paper, we demonstrate that the test of URWFs is more effective in terms of resistive defect detection than that of URRFs and we list the necessary test conditions to detect them.

Microfluidic Spinning of Cell‐Responsive Grooved Microfibers

Engineering living tissues that simulate their natural counterparts is a dynamic area of research. Among the various models of biological tissues being developed, fiber‐shaped cellular architectures, which can be used as artificial blood vessels or muscle fibers, have drawn particular attention. However, the fabrication of continuous microfiber substrates for culturing cells is still limited to a restricted number of polymers (e.g., alginate) having easy processability but poor cell–material interaction properties. Moreover, the typical smooth surface of a synthetic fiber does not replicate the micro‐ and nanofeatures observed in vivo, which guide and regulate cell behavior. In this study, a method to fabricate photocrosslinkable cell‐responsive methacrylamide‐modified gelatin (GelMA) fibers with exquisite microstructured surfaces by using a microfluidic device is developed. These hydrogel fibers with microgrooved surfaces efficiently promote cell encapsulation and adhesion. GelMA fibers significantly promote the viability of cells encapsulated in/or grown on the fibers compared with similar grooved alginate fibers used as controls. Importantly, the grooves engraved on the GelMA fibers induce cell alignment. Furthermore, the GelMA fibers exhibit excellent processability and could be wound into various shapes. These microstructured GelMA fibers have great potential as templates for the creation of fiber‐shaped tissues or tissue microstructures.     

Mlcrolasers based on silica microspheres

Light can be confined efficiently in the high-Q, small-volume whispering-gallery-modes observed in silica microspheres. By coupling these microspheres to eroded optical fibers and fiber tips, direct mapping of the whispering-gallery modes has been achieved and the mode numbers have been assessed. The properties of these modes have allowed us to obtain laser action with very low thresholds in Nd-doped silica microspheres. Further projects in the field of non-linear optics and cavity quantum electrodynamics are described.