Economic Evaluation of Reinforced Concrete Structures with Columns Reinforced with Prefabricated Cage System

A new reinforcement system termed the prefabricated cage system (PCS) that can be used as an alternative to the rebar reinforcement cage is economically evaluated. PCS is a prefabricated reinforcement that enables easier, faster, and more reliable construction. Use of PCS shortens the construction schedule time and lowers total construction cost. This is important to both owners and construction contractors. The engineering economics methods presented in this paper would also be of interest to researchers. Reinforced concrete structures with PCS reinforced columns have been considered in this research, as it is one of the major applications of PCS. Various parameters affecting the economics of PCS are reviewed and a case study structure is analyzed comparing the costs of the structure with rebar reinforced columns to costs of the structure with PCS reinforced columns. The investigation shows that using PCS results in a 33.3% time savings and a 7.1% cost savings over rebar for each column. This results in an average of 3.6% savings on total project cost; an average of 22.2% savings on total column costs; 20.4% savings on total project time period, and 33.3% savings on columns construction time period. The cost savings are estimated based on production of small quantities of PCS reinforcement. Mass production of PCS reinforcement would result in even higher cost savings.     

Public value capturing in urban renewal: the fikirtepe case (Istanbul,Turkey)

Journal of Housing and the Built Environment - Public Value Capture (PVC) refers to the capture of the value created through the efforts of public bodies rather than from those of private...     

Cross‐level fragility analysis of modularized suspended buildings based on experimentally validated numerical models

Suspended buildings typically have a core as the primary and suspended floors as the secondary structures. These configurations offer visual transparency, smaller vertical components, and seismic attenuation via the primary–secondary structure interaction. Such attenuation is further enhanced by the modularization of the suspended segment which allows large drifts but prevents them from causing damage. Previously conducted shake‐table tests have confirmed these features. However, how the component performance contributes to system performance has not been quantitated. To address this gap, fragility analyses are conducted for 10‐story experimentally validated models with optimized supplemental dampers and inter‐module stiffness. Multiple limit state functions are proposed to provide a full account of damage sources. Additionally, a mapping rule from the component‐level to the system‐level limit states is developed which captures the influence of damage distribution on system‐level limit states. Results for the uncontrolled suspended building indicate that for the PGV of 0.5 m/s, the failure probabilities of the repairable and life safety limit states are 97% and 83%, respectively. These probabilities are 92% and 27% for the frame structure with viscous dampers, 58% and 5% for the passive‐controlled modularized suspended building system (MSBS), and 45% and 3% for MSBS with optimal vertical distributions of modularized secondary structure.     

A modified method for processing and characterization of organoclay‐based poly(ethylene terephthalate) nanocomposite fibers

In the current study, in order to prepare poly(ethylene terephthalate) (PET)/organoclay nanocomposite fibers, a slurry‐compounding method (SCM) was applied and compared to conventional melt‐compounding method (CMM) in terms of the dispersion of organoclays and the performance of the spun and or drawn fibers. The organoclays were synthesized by using three different alkyl phosphonium salts and compared with commercially available alkyl ammonium‐modified organoclays in terms of thermal stability and basal spacing. It was found that the alkyl phosphonium salts exhibited higher thermal stability and basal spacing with respect to commercial alkyl ammonium organoclays. Among them, tributylhexadecylphosphonium bromide resulted in superior properties; therefore, it was used to prepare the nanocomposite PET fibers. The organoclay content of 0.1–1 wt% was taken as the material parameter. It was demonstrated that the SCM yielded better dispersion of organoclays with respect to CMM. The drawn nanocomposite fibers prepared via SCM exhibited improved tensile strength and modulus in comparison to the neat‐PET. The maximum tensile properties for fibers were obtained at 0.5% organoclay loading in SCM. The thermal properties and the percentage of crystallinity were investigated by differential scanning calorimetry analysis. In addition, Fourier transform infrared spectroscopy was utilized to obtain the percentage of crystallinity of the fibers. POLYM. COMPOS., 34:887–896, 2013. © 2013 Society of Plastics Engineers     

Multi-resolution Wavelet Analysis for Ferroresonance Phenomena in Power Systems

Power systems struggle from many effects, causing over-voltages and over-currents. One of these effects is ferroresonance, which is a non-linear phenomenon that occurs when the system is unbalanced. This article focuses on a 380-kV transmission line from Turkey's electrical power network where ferroresonance occurs during a switching operation. The system is first simulated on MATLAB (The MathWorks, Natick, Massachusetts, USA) model, and voltage variations are obtained. Spectral analysis methods are applied to the signal, and the frequency components of the system are examined for ferroresonant conditions. According to the obtained frequency components, the steady-state behavior of the system is explained.     

Spatially Resolved Photoemission and Electrochemical Characterization of a Single-Chamber Solid Oxide Fuel Cell

The present paper pinpoints the feasibility of in operando near-ambient pressure characterization of an operating single chamber solid oxide fuel cell (SC-SOFC) by means of spatially resolved X-ray photoelectron spectroscopy. The results are based on an innovative and unique setup expanding the capabilities of the scanning photoelectron microscopes. In particular, the impact of getting access to the low mbar range on the very observability of chemical-state changes in an LSM cathode have been highlighted. Ex situ and in situ electrochemical measurements at OCP and close circuit cell conditions complemented the photoemission mapping and spectroscopy. The latter has evidenced the evolution of the chemical state of Sr upon the exposure of the typical SC-SOFC CH₄–O₂ gas feed.     

DNA base sensor characteristics of polymeric-nanocomposite electrode

The electrochemical synthesis of polyaniline films was carried out by potential sweep method in sulfuric acid solution at the glassy carbon electrode. The electrocatalytic behavior to DNA bases (adenine and guanine), uric acid, and dopamine of polyaniline nanocomposite sensor modified with nano-gold particles was investigated by DPV technique. By systematically examining the effects of the possible parameters affecting the electrocatalytic performance of the relevant sensor, the optimal value for the each parameter was determined. The detailed electrocatalytic studies of the optimized sensor revealed that this sensor could be used as DNA base sensor for guanine in the presence of adenine, dopamine, and uric acid. Moreover, the performance of the relevant sensor in thermally denatured fish sperm DNA was quite satisfactory.     

Effects of Bi content on thermal,microstructure and mechanical properties of Sn-Bi-In-Zn solder alloy systems

Journal of Materials Science: Materials in Electronics - In the present study, various amounts of Bi were added to two groups of Sn-In-Zn lead-free solder alloy systems (Sn-[x] Bi-2In-9Zn...     

Optical response of Ag-Au bimetallic nanoparticles to electron storage in aqueous medium

Composition and structure dependence of the shift in the position of the surface plasmon resonance band upon introduction of NaBH4 to aqueous solutions of gold and silver nanoparticles are presented. Silver and gold nanoalloys in different compositions were prepared by co-reduction of the corresponding salt mixtures using sodium citrate as the reducing agent. After addition of NaBH4 to the resultant nanoalloys, the maximum of their surface plasmon resonance band, ranging between that of pure silver (ca. 400 nm) and of pure gold (ca. 530 nm), is blue-shifted as a result of electron storage on the particles. The extent of this blue shift increases non-linearly with the mole fraction of silver in the nanoparticle, parallel to the trends reported previously for both the frequency and the extinction coefficient of the plasmon band shifts. Gold(core)@silver(shell) nanoparticles were prepared by sequential reduction of gold and silver, where addition of NaBH4 results in relatively large spectral shift in the plasmon resonance band when compared with the nanoalloys having a similar overall composition. The origin of the large plasmon band shift in the core-shell is related with a higher silver surface concentration on these particles. Hence, the chemical nature of the nanoparticle emerges as the dominating factor contributing to the extent of the spectral shift as a result of electron storage in bimetallic systems.     

The measurement of interfacial energies for solid Sn solution in equilibrium with the Sn–Bi–Ag liquid

The equilibrated grain boundary groove shapes of solid Sn solution in equilibrium with Sn–Bi–Ag liquid were observed from a quenched sample by using a radial heat flow apparatus. The Gibbs–Thomson coefficient, solid–liquid interfacial energy, and grain boundary energy of the solid Sn solution were determined from the observed grain boundary groove shapes. The thermal conductivity of the solid phase for Sn-10 at.%Bi-2 at.%Ag alloy and the thermal conductivity ratio of the liquid phase to the solid phase for Sn-10 at.%Bi-2 at.%Ag alloy at the melting temperature were also measured with a radial heat flow apparatus and a Bridgman-type growth apparatus, respectively. A comparison of present results for solid Sn solution in the Sn–10 at.%Bi–2 at.%Ag alloy with the results obtained in previous works for similar solid Sn in equilibrium with different binary or ternary liquid was made. From the comparison, it can be concluded that for solid Sn solution in equilibrium with different liquid, the Gibbs–Thomson coefficient seems to be constant and does not depend on the composition of liquid but solid–liquid interfacial energy changes little bit with composition of liquid at a constant temperature.