Optical and electronic properties of cobalt-doped zinc oxide films prepared by the sputtering method

In-doped ZnO, Co-doped ZnO and Li-doped NiO are successively deposited on quartz by the sputtering method. A current versus voltage curve of the three-layer device, in which the Indoped ZnO and Li-doped NiO are used as electrodes, reveals that the In-doped ZnO is an ohmic electrode and the Li-doped NiO is a blocking electrode with respect to electron injection. In photocurrent spectra of the three-layer device, there are two distinct peaks around 410 and 640 nm. The former is ascribed to the photoionization caused by the electric-dipole transition from the ground states,⁴A₂(F), to the conduction band, and the latter to the thermal emission from electronic excited states of Co²⁺,⁴T₁(P).     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

An approach to the generalized nurse scheduling problem--generation of a declarative program to represent institution-specific knowledge.

An approach to the nurse scheduling problem is presented. The critical problem in nurse scheduling in a hospital is how to determine the day-to-day shift assignments of each nurse for a specified period in a way that satisfies the given requirements as much as possible, where the requirements differ greatly depending on the hospital. We present a method for constructing an agency-independent core procedure which can be tailored to the peculiar requirements of an individual hospital. As a basis, a formal analysis of the problem was performed, and a general scheduling procedure was established. Based on the method, a software system which produces a scheduling program for a given institution was developed. A declarative program that represents institution-specific information is generated through an interview with the user and incorporated into the general procedure. Some of the programming technicalities and an application of the system are also presented.     

Dissolution of phase-separated domains after a jump to a temperature in the single-phase region

Phase-separated domains prepared in the two-phase region were dissolved at a temperature in the single-phase region, and their dissolution dynamics was studied by using the time-resolved light scattering (TRLS) technique and a scanning electron microscope (SEM). The time t_ps of preparation of domains was chosen to be long enough for phase separation to proceed into the late stage. The scattered light intensity at small wavenumbers increased before it attenuated. As t_ps increased, the increase at smaller wavenumbers became more significant and the peak intensity decreased only slightly with dissolution time. The characteristic wavenumber q_m evaluated from TRLS and SEM followed the power-law relation q_mt^−0.3.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

Furnace grown gate oxynitride using nitric oxide (NO)

Gate oxynitride was grown in NO for the first time. This approach can provide a tight N accumulation near the Si/SiO₂ interface. Much lower thermal budget is required for an NO process than for an N₂O process to produce an oxynitride with useful properties. Submicron MOSFET's with NO oxynitride showed superior current drive characteristics and comparable hot carrier immunity to those with N₂O oxynitride     

Improvements of the T-Ω method for 3-D eddy currentanalysis

An improved T-Ω method that can analyze magnetic fields produced not only by eddy currents but also by magnetizing currents is proposed. The method is applied to the analysis of 3-D eddy-current models with holes. The usefulness of the method is investigated by comparing calculated results with measured results and with results obtained by the A-Φ method. The T-Ω method has the advantage that the CPU time can be considerably reduced when most of the analyzed region is current-free and the eddy current flows two-dimensionally. The method is especially effective when the shape of the winding is simple and the distribution of magnetizing current is known beforehand. It is not effective when most of the analyzed region is current-carrying     

Characterization of C-S-H from Highly Reactive β-Dicalcium Silicate Prepared from Hillebrandite

β-dicalcium silicate synthesized by thermal dissociation of hydrothermally prepared hillebrandite (Ca₂(SiO₃)(OH)₂) exhibits extremely high hydration activity. Characterization of the hydrates obtained and investigation of the hydration mechanism was carried out with the aid of trimethylsilylation analysis, ²⁹Si magic angle spinning nuclear magnetic resonance, transmission electron microscopy selected area electron diffraction, and XRD. The silicate anion structure of C-S-H consisted mainly of a dimer and a single-chain polymer. Polymerization advances with increasing curing temperature and curing time. The C-S-H has an oriented fibrous structure and exhibits a 0.73-nm dreierketten in the longitudinal direction. On heating, the C-S-H dissociates to form β-C₂S. The temperature at which βC₂S begins to form decreases with increasing chain length of the C-S-H or as the Ca/Si ratio becomes higher. The high activity of β-C₂S is due to its large specific surface area and the fact that the hydration is chemical-reaction-rate-controlled until its completion. As a result, the hydration progresses in situ and C-S-H with a high Ca/Si ratio is formed.     

Optical bistability and set-reset operation of a Fabry-Perotsemiconductor laser amplifier with two detuned light injections

Optical bistability in a Fabry-Perot semiconductor laser amplifier when two optical inputs detuned from the resonant wavelength of a semiconductor laser amplifier are injected is discussed. A split branch is found in the optical output versus input characteristics in addition to conventional optical bistability behavior. It is shown analytically and experimentally that set and reset can be achieved in the optical output of the semiconductor laser amplifier for each wavelength by applying two detuned optical pulses and using the split branch