A multilevel PWM strategy suitable for high‐voltage motor direct drive systems with consideration of the adverse effect of dead time

Recently, high‐voltage motor direct drive systems have been put to practical use, and various multilevel PWM strategies have also been proposed. This paper describes a multilevel PWM strategy [our group calls it the Carrier Phase Selection Method (CPS)] that has the lowest line voltage harmonic distortion in order to prevent the degradation of high‐voltage motor winding insulations. This method takes the adverse effect of dead time into consideration, and it controls the shift direction of a carrier phase. Therefore, a favorable output waveform without instantaneous voltage surges is achieved even if the line voltage level changes. Moreover, the switching transitions across all switching devices are well‐balanced, so the utilization of inverter unit cells is equalized. This is an important factor when designing the entire system. Based on simulation and experimental results, it is shown that this CPS method is particularly effective in high‐voltage motor direct drive systems. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 165(2): 77–88, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20474     

Orientation of nanowires consisting of poly(3-hexylthiophene) using strong magnetic field

Nanowires consisting of regioregular poly(3-hexylthiophene) (P3HT) as a conducting polymer were prepared using p-xylene. Magnetic processing of the nanowires was carried out using two superconducting magnets with horizontal (B_max = 8 T) and vertical (B_max = 10 T) directions. The formation of the nanowires was confirmed by atomic force microscopy (AFM) measurement. The results from the AFM images and the polarized absorption spectra on glass plates indicated that the nanowires partly oriented themselves with their long axes, which are parallel to the π–π stacking direction, being perpendicular to the magnetic field. The magnetic orientation is most likely ascribed to anisotropy in the magnetic susceptibilities of the ordered P3HT in the nanowires.     

Pb-free surface-finishing on electronic components’ terminals for Pb-free soldering assembly

Pb-free solderable surface finishing is essential to implement Pb-free solder assembly in order to meet with the growing demand of environmental consciousness to eliminate Pb from electronic products. Two types of widely applicable Pb-free surface finishing technologies are developed. One is the multilayer-system including Pd with Ni undercoat. Heat-resistance of Pd enables whole-surface-plating on to leadframe before IC-assembling process. The other is the double-layer-system with low-melting-point-materials, for example, thicker Sn underlayer and thinner Sn-Bi alloy overlayer, dilutes Sn-Bi alloy’s defects of harmful reactivity along with substrate metal and mechanical brittleness with keeping its advantages of solder-wettability and no whisker.     

Artifact reduction using reliability reasoning for image generation of FTV

In this paper, we present a new view synthesis method in multiview camera configurations of Free viewpoint TV (FTV) where potential depth errors are considered. The emphasis is on the artifacts eliminating for photorealistic synthesis especially near object boundaries. In contrast to conventional techniques which ignore geometry errors, we first categorize the artifact cases and depth modes. Furthermore, this paper infers the complementarity principle of the artifacts from left and right references. This complementarity guarantees the effectiveness of our reliability-based synthesis. The reliability reasoning is crucial for artifacts reduction. The reliable and unreliable areas from different views can be correctly labeled. Then artifacts caused by unreliable pixels from one reference can be replaced by the reliable pixels from the other reference. As a final result, artifacts of novel view are demonstrated to be significantly reduced on different multiview sequences.     

Nondestructive Quantitative Evaluation of Porosity Volume Distribution in Aluminum Alloy Die Castings by Fractal Analysis

The nondestructive and three-dimensional quantitative evaluation of porosity in aluminum alloy die castings is proposed to identify whether the predominant cause of pore formation is shrinkage or entrapped gas. The validity of this method of evaluation was shown by comparing two different regions with different ratios of pores formed by shrinkage and gas. It was shown that the proposed evaluation can be used as a quantitative indication of porosity.     

Estimation of passive cooling efficiency for environmental design in Brazil

An estimation of passive cooling techniques was conducted for 14 cities in Brazil, using a fairly accurate algorithm that accounts for heat conduction, convection, radiation, and evaporation; this was done to determine the amount of heat gain/loss of room air, defined as a particular quantitative index for passive techniques. Heat gains and losses were calculated for four envelope conditions - namely, insulated, high-albedo, wet surface, and a combination of the previous two - and compared to a case assumed to be the standard condition. A conclusion drawn was that a passive design is efficient in decreasing the need for cooling in typical dwellings in Brazil; solutions should differ with regional climate characteristics. In semi-arid areas, evaporative cooling showed the best results. Reduced heat gain was found during the warm seasons for all cities, along with increased heat gain during the cool seasons for mid-latitude cities. In particular, a combination of high-albedo enveloping and evaporation can greatly decrease heat gain in building walls. High-albedo surfaces in the sub-tropical areas found in southern Brazil are more efficient. It is suggested that passive techniques should be conceived in such a way so as to work during the cooling season and be disabled during mild ones.     

Repeatable change in electrical resistance of Si surface by mechanical and electrical nanoprocessing

The properties of mechanically and electrically processed silicon surfaces were evaluated by atomic force microscopy (AFM). Silicon specimens were processed using an electrically conductive diamond tip with and without vibration. After the electrical processing, protuberances were generated and the electric current through the silicon surface decreased because of local anodic oxidation. Grooves were formed by mechanical processing without vibration, and the electric current increased. In contrast, mechanical processing with vibration caused the surface to protuberate and the electrical resistance increased similar to that observed for electrical processing. With sequential processing, the local oxide layer formed by electrical processing can be removed by mechanical processing using the same tip without vibration. Although the electrical resistance is decreased by the mechanical processing without vibration, additional electrical processing on the mechanically processed area further increases the electrical resistance of the surface.