Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry     

Data retention characteristics of sub-100 nm NAND flash memory cells

In contrast to the conventional theories, we have revealed that the most distinguished mechanism in the data retention phenomenon after Fowler-Nordheim (FN) stress in sub-100 nm NAND Flash memory cells is the annihilation of interface states. Interface state generation rate increases rapidly as the channel width of NAND flash cell decreases. Comparison of interface states and stress-induced leakage current (SILC) component during retention mode shows that the annihilation of interface states strongly affects data retention characteristics of the programmed cells.     

Catalytic dehydrogenation of ethylbenzene with carbon dioxide: promotional effect of antimony in supported vanadium–antimony oxide catalyst

Alumina-supported vanadium oxide, VO_x/Al₂O₃, and binary vanadium–antimony oxides, VSbO_x/Al₂O₃, have been tested in the ethylbenzene dehydrogenation with carbon dioxide and characterized by S_BET, X-ray diffraction, X-ray photoelectron spectroscopy, hydrogen temperature-programmed reduction and CO₂ pulse methods. VSbO_x/Al₂O₃ exhibited enhanced catalytic activity and especially on-stream stability compared to VO_x/Al₂O₃ catalyst. Incorporation of antimony into VO_x/Al₂O₃ increased dispersion of active VO_x species, enhanced redox properties of the systems and formed a new mixed vanadium–antimony oxide phase in the most catalytically efficient V_0.43Sb_0.57O_x/Al₂O₃ system.     

A new time-domain discontinuous space-vector PWM technique in overmodulation region

A new discontinuous modulation method based on space-vector control is proposed and analyzed. The proposed technique employs a pulse-dropping method and is designed in the time domain. It features a very wide modulation range while maintaining the required waveform qualities and switching numbers in the overmodulation region. Since the modulation method and modulation index equation are simple, the proposed technique can be easily implemented by software and is applicable to the overmodulation region in ac motor drives. The performance indexes are discussed and experiments have been performed.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Einfluß der Korngröße auf mechanische Eigenschaften und den ungeschmierten reversierenden Gleitverschleiß von Al2O3-Keramik

Influence of grain size on mechanical properties and dry oscillating sliding wear of Al₂O₃-ceramics Specimens with average grain sizes varying between about 0.8 μm and 12 μm were produced by cold isostatic pressing of high purity Al₂O₃-powder followed by sintering between 1300°C and 1700°C. Hardness, Young's modulus, bending strength and fracture toughness were measured as a function of average grain sizes. Tribological tests were carried out on the different microstructures at normal laboratory air and room temperature by using a ring-on-block tribometer. Experimental results showed the dependence of mechanical properties on grain size, hardness and bending strength obeying a Hall-Petch type relation, approximately. Coefficient of friction was relatively independent of grain size under the test conditions used. However, wear intensity increased substantially if a critical grain size was surpassed. This was due to a change in mechanisms of material removal which was confirmed by scanning electron microscopical studies of the worn surfaces.     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.     

The design of experiments when there are errors in all the variables

The Error-in-Variables Model (EVM) applies to a large class of problems in parameter estimation in which there is error in all the variables. This property makes it of more general applicability than the widely used technique of ordinary Least Squares. While there is a voluminous literature on EVM there is nothing on a general method for designing experiments when EVM applies. In this paper we present an extension of the concept of D-optimality to provide such a general method. It is illustrated by applying it to the estimation of copolymer reactivity ratios and to fitting an ellipse.