An analytical model for high electron mobility transistors

In this paper we present a new model for HEMT's which is based on a single analytical function that describes the electron concentrations in the two dimensional electron gas and in the AlGaAs layer. Besides accounting for the AlGaAs conduction, the model includes the effect of mobility degradation, channel length modulation in the saturation region and the series resistances R_S and R_D. The model results in closed form expressions for the current, transconductance, output conductance and gate capacitance. Finally, the theoretical predictions of the model are compared with the experimental data and shown to be in good agreement over a wide range of bias conditions     

Over GHz electrical circuit model of a high-density multiple line grid array (MLGA) interposer

The multiple line grid array (MLGA) interposer was recently introduced as a future high-density high-speed bonding method. In this paper, we introduce an electrical model and high-frequency characteristics of the MLGA interposer. The high-frequency electrical model was extracted from microwave S-parameter measurements up to 20 GHz as well as from fundamental microwave network analysis. For the parameter fitting process during model extraction, an optimization method was used. Several different types of MLGA interposers were designed, assembled and tested. The test vehicles contained coplanar waveguides, probing pads and an MLGA interposer structure. The height of the MLGA, the conductor shape inside the MLGA, and the dielectric insulator of the MLGA were varied. From the model, an MLGA with a height of 0.4 mm and a polymer dielectric insulator was found to have 203 pH of self inductance, 49 pH of mutual inductance with the nearest ground conductor line, and 186 fF of mutual capacitance. By reducing the height of the MLGA and by using an insulator with a lower dielectric constant, parasitic inductance and capacitance is further reduced. TDR/TDT simulation and measurement showed the validity of the extracted model parameters of the MLGA interposer. Circuit simulation based on the extracted model revealed that the MLGA interposer could be successfully used for microwave device packages up to 20 GHz and for high-speed digital device packages with a clock cycle up to 5 GHz.     

Monolithic SiGe Up‐/Down‐Conversion Mixers with Active Baluns

The purpose of this paper is to describe the implementation of monolithically matching circuits, interface circuits, and RF core circuits to the same substrate. We designed and fabricated on‐chip 1 to 6 GHz up‐conversion and 1 to 8 GHz down‐conversion mixers using a 0.8 µm SiGe hetero‐junction bipolar transistor (HBT) process technology. To fabricate a SiGe HBT, we used a reduced pressure chemical vapor deposition (RPCVD) system to grow a base epitaxial layer, and we adopted local oxidation of silicon (LOCOS) isolation to separate the device terminals. An up‐conversion mixer was implemented on‐chip using an intermediate frequency (IF) matching circuit, local oscillator (LO)/radio frequency (RF) wideband matching circuits, LO/IF input balun circuits, and an RF output balun circuit. The measured results of the fabricated up‐conversion mixer show a positive power conversion gain from 1 to 6 GHz and a bandwidth of about 4.5 GHz. Also, the down‐conversion mixer was implemented on‐chip using LO/RF wideband matching circuits, LO/RF input balun circuits, and an IF output balun circuit. The measured results of the fabricated down‐conversion mixer show a positive power conversion gain from 1 to 8 GHz and a bandwidth of about 4.5 GHz.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

Effects of potential and heat treatment on phase transition of alumina dielectric layer

The characteristics and growth behaviors of alumina dielectric layer formed by anodic oxidation were investigated. The aluminum oxide layer anodized at 400 V was predominantly amorphous alumina, but at the applied potentials more than 500 V, amorphous and crystalline γ-alumina were existed in anodic oxide layer and the ratio of γ-alumina increased with the increasing applied potential. During the heat treatment at 600^°C or higher temperature, amorphous alumina layer was transformed into the crystalline γ-alumina. The phase transition of anodic amorphous alumina into crystalline depends on anodic applied potentials and heat-treatment temperatures.     

Nanoporous activated carbon cloth for capacitive deionization of aqueous solution

Activated nanostructured-carbon cloths with a high ratio of surface area to volume are used as electrode for capacitive deionization. The electrochemical properties on capacitive deionization for NaCl solution have been investigated to improve efficiency of capacitive deionization properties from aqueous solution, employing chemical surface-modification by etching in alkaline and acidic solution. The removal efficiency of inorganic salts of activated carbon cloths by chemical modification significantly increased. Specially the carbon cloth surface modified in HNO₃ showed an effect of improvement in the CDI efficiency due to not only ion adsorption by an electric double layer, but also electron transfer by Faradaic reaction.     

Analysis of hazard area associated with hydrogen gas transmission pipelines

Hydrogen is considered to be the most important future energy carrier in many applications reducing significantly greenhouse gas emissions, but the safety issues associated with hydrogen applications need to be investigated and fully understood to be applicable as the carrier. Generally, the locations of hydrogen production and consumption are different. Hydrogen must be transported from the point of production to the point of use. Pipeline delivery is cheaper than all other methods for large quantities of hydrogen. The rupture of a hydrogen pipeline can lead to outcomes that can pose a significant threat to people and property in the immediate vicinity of the failure point. In this work, a simplified equation of hazard analysis is proposed for the pipeline transporting hydrogen, which relates the diameter, the operating pressure and the length of the pipeline to the size of the affected area in the event of a failure of the pipeline. The dominant hazards are thermal radiation from sustained fire and shock pressure from gas cloud explosion. For a transmission pipeline of hydrogen gas, the hazard area from the fire is slightly larger than by the other event. The hazard area is directly proportional to the operating pressure raised to the power one-half, and to the pipeline diameter. This simplified equation to estimate the hazard area will be a useful tool for safety management of hydrogen gas transmission pipelines.     

Error Concealment Based on Semantic Prioritization with Hardware‐Based Face Tracking

With video compression standards such as MPEG‐4, a transmission error happens in a video‐packet basis, rather than in a macroblock basis. In this context, we propose a semantic error prioritization method that determines the size of a video packet based on the importance of its contents. A video packet length is made to be short for an important area such as a facial area in order to reduce the possibility of error accumulation. To facilitate the semantic error prioritization, an efficient hardware algorithm for face tracking is proposed. The increase of hardware complexity is minimal because a motion estimation engine is efficiently re‐used for face tracking. Experimental results demonstrate that the facial area is well protected with the proposed scheme.     

Photodegradation mechanism and stabilization of polyphenylene oxide and rigid‐rod polymers

Poly(2,4‐dimethyl‐1,4‐phenylene oxide) (PPO), poly(benzo[1,2‐d:5,4‐d′]bisoxazole‐2,6‐diyl‐1,4‐phenylene) (PBO) and poly(benzo[1,2‐d:4,5‐d′]bisthiazole‐2,6‐diyl‐1,4‐phenylene) (PBZT), which are polymers with extended conjugated structures, undergo a self‐sensitized photo‐induced electron‐transfer reaction. A second component is not required. This article presents many similar observations on these polymers when they are exposed to light and evidence to support the proposed photo‐induced electron‐transfer mechanism. Methods to stabilize these polymers against photo‐oxidation are also described. Workers investigating other conjugated polymeric systems may find the experimental methods, observations and polymer stabilization approaches discussed in this review useful. Copyright © 2005 Society of Chemical Industry