Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Performance of GaAs-AlGaAs V-grooved inner stripe quantum-well wirelasers with different current blocking configurations

GaAs-AlGaAs V-grooved inner stripe (VIS) quantum-well wire (QWW) lasers grown by metalorganic chemical vapor deposition with different current blocking configurations, n-blocking on p-substrate (VIPS), p-n-p-n blocking on n-substrate (VI(PN)_nS) and p-blocking on n-substrate (VINS) have been fabricated and characterized. The VIPS QWW lasers show the most stable characteristics with effective current confinement: one of the lasers shows fundamental transverse mode, lasing up to 5 mW/facet, typical threshold current of 39.9 mA at 818.5 mm, an external differential quantum efficiency of 24%/facet, and characteristic temperature of 92 K. The current tuning rate was almost linear at 0.031 mm/mA, and the temperature tuning rate was measured to be 0.14 nm/°C. Comparison of the light output versus current characteristics of the lasers with different current blocking configurations is presented here     

Pollutant dispersion over two-dimensional hilly terrain

Numerical prediction of the wind flow and pollutant dispersion over two-dimensional hilly terrain is presented. The wind tunnel experiments are conducted to validate the numerical results of the flow field. Measured mean velocity profiles, turbulence characteristics, and surface pressure distributions show good agreement with the numerical predictions. The hypothesis of Reynolds number independency for an atmospheric boundary layer flow over aerodynamically rough terrain is numerically confirmed. The linear theory provides generally good prediction of speed-up characteristics for gently sloped low hills. The effect of two-dimensional double hills on the dispersion of pollutants from continuously or temporally released line source of different emission heights and locations is also investigated. The ground-level concentrations are considerably reduced as emission heights are increased. The variances of ground-level concentration with respect to time from a temporally released source are strongly influenced by the flow separation.     

Transluminal balloon angioplasty, stents, and atherectomy

Arterial bypass grafting for occlusive disease is still considered the gold standard in the treatment of arterial occlusive disease. However, less invasive methods are available for select patients. Percutaneous balloon angioplasty has been shown to be effective in focal iliac artery stenosis, with patency rates of 50% to 90% at 5 years. Patency rates for femoropopliteal lesions are generally less than 50% at 2 years. Complications seen with balloon angioplasty often can be treated with arterial stents. Stents can be categorized into balloon-expandable, which provide a rigid scaffold to support the artery, self-expanding, which exert radial force to resist external compression, and thermal expanding stents, which allow for the use of a smaller introducer sheath. Another treatment option is atherectomy, in which the offending lesion is removed instead of fracturing and dilating the lumen. Although overall initial results of atherectomy have not been favorable, short lesions with eccentric atheroma or intimal hyperplasia, such as those seen in dialysis access fistulas or vein graft stenoses, may respond well.     

Amorphous Ni---N---W film as a diffusion barrier between aluminum and silicon

The influence of nitrogen on the diffusion barrier properties of amorphous Ni---W films was studied. Nitrogen was introduced into the amorphous Ni---W film by co-sputtering nickel and tungsten in a premixed gas mixture of 90% Ar and 10% N₂, resulting in the formation of amorphous Ni₃₀N₂₁W₄₉ film. X-ray analysis indicates a detectable crystallization of the amorphous film after 30 min annealing in vacuum at 600°C, accompanied by the formation of W₂N, but backscattering spectrometry (BS) reveals a reaction with silicon only at about 725°C. The Schottky barrier height of this amorphous film on n-Si is stable for 30 min annealing up to at least 550°C. With an aluminum overlayer, BS indicates that an amorphous Ni₃₀N₂₁W₄₉ film effectively prevents the metallurgical interaction between aluminum and silicon for 30 min up to 600°C. The Schottky barrier height of that contact configuration is also stable up to at least 550°C, suggesting that amorphous Ni---N---W films have attractive features as diffusion barriers.     

Analysis of color symbology from the perspective of cultural semiotics focused on Korean costume colors according to the cultural changes

The purpose of this study was to analyze the symbolization of colors as cultural codes, based on costume colors. In order to study the significance of colors in cultural changes, we carried out a quantitative analysis and interpreted it from the perspective of cultural semiotics. The range of this study was focused on Korean costume colors, over diverse diachronic stages of Korean culture. For this study 1535 color samples were collected, measured with a spectrophotometer, and analyzed quantitatively according their diachronic stages of origin. As a result, red, blue, and yellow were found to be the most frequently used colors during the Chosun Dynasty, a period based on Confucianism. These colors acted as cultural codes with cultural significance. During the Modern times pink, light blue, and black increased in frequency and represented the reception of western culture, the changing sex role of women in society, and utilitarianism. In these days, neutral colors and grayish tones of all colors are the most significant colors of high frequency. The use of such colors is closely related to industrialization, mechanization, functionalism, and the changes of women's sex roles in the societies. They are used as cultural codes, especially to emphasize a rational and masculine image rather than a feminine image. © 2006 Wiley Periodicals, Inc. Col Res Appl, 32, 71–79, 2007; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20290     

A micromachined electrochemical sensor for free chlorine monitoring in drinking water.

In this work, we designed, fabricated and tested a disposable, flow-through amperometric sensor for free chlorine determination in water. The sensor is based on the principle of an electrochemical cell. The substrate, as well as the top microfluidic layer, is made up of a polymer material. The advantages include; (a) disposability from low cost; (b) stable operation range from three-electrode design; (c) fluidic interconnections that provide on line testing capabilities; and (d) transparent substrate which provides for future integration of on-chip optics. The sensor showed a good response and linearity in the chlorine concentration ranging from 0.3 to 1.6 ppm, which applies to common chlorination process for drinking water purification.     

Volumetric three‐dimensional up‐conversion display medium

Abstract— Several rare‐earth‐doped fluoride crystals that are excited to emit visible light by sequential two‐photon absorption have been investigated as display‐medium candidates for static volumetric three‐dimensional displays. Dispersion of powders of these materials in a refractive‐index‐matched polymer is reported because such a medium may result in a scalable display. The scattering problem in such a medium is greatly reduced by index‐matching the polymer to the crystalline particles. An index‐matching condition that optimizes the performance is identified.     

Dichotomous behavior of polymer melts in isothermal melt spinning

Isothermal melt spinning experiments have been conducted using two polyethylene melts of low density (LDPE) and high density (HDPE) to produce steady state spinline profiles. The data revealed the threadline extensional viscosity exhibiting a contrasting picture : extension thickening behavior for LDPE and extension thinning one for HDPE. A White-Metzner model having a strain rate-dependent relaxation time was then found to be able to simulate this dichotomy in melt spinning fairly well: the fluids whose relaxation times have smaller strain rate-dependence can fit LDPE data with extension thickening extensional viscosity whereas the fluids whose relaxation times have larger strain rate-dependence can fit HDPE data with extension thinning extensional viscosity. This dichotomous nature of viscoelastic fluids is also believed to be able to explain other similar contrasting phenomena exhibited by polymer melts, such as vortex/no vortex in entry flows, cohesive/ductile fracture modes in extension, and more/less stable draw resonance than Newtonian fluids.