高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Application of a multi-channel system for continuous monitoring and an early warning system.

A multi-channel continuous toxicity monitoring system developed in our laboratory, based on two-stage mini-bioreactors, was successfully implemented in the form of computer-based data acquisition. The multi-channel system consists of a series of a two-stage minibioreactor systems connected by a fiber optic probe to a luminometer, and uses genetically engineered bioluminescent bacteria for the detection of the potential toxicity from the soluble chemicals. This system can be stably and continuously operated due to the separation of the culture reactor from the test reactor and accomplish easy and long-term monitoring without system shut down by abrupt inflows of severe polluting chemicals. Four different recombinant bioluminescent bacteria were used in different channels so that the modes of the samples toxicities can be reasonably identified and evaluated based upon the response signature of each channel. The bioluminescent signatures were delivered from four channels by switching one at once, while the data is automatically logged to an IBM compatible computer. We also achieved the enhancement of the system through the manipulation of the dilution rate and the use of thermo-lux fusion strains. Finally, this system is now being implemented to a drinking water reservoir and river for remote sensing as an early warning system.     

高压脉冲放电处理含氰废水的影响因素探讨

焦化废水中含有大量的氰化物,必须采取有效措施进行去除,传统去除方法运行成本高、操作复杂。提出了用高压毫微秒脉冲产生的非平衡等离子体处理含氰废水的方法,对其影响因素pH值、放电时间、气流量、放电条件等进行了大量的实验研究,结果表明:溶液初始pH值为9.09,放电2 h,放电电压46 kV时氰化物的去除率最高可达93.2%,氰化物质量浓度可降至0.26 mg/L。实验对比了放电与不放电氰化物的去除效果:相同条件下放电后氰化物的去除率大大提高,为焦化废水中氰化物的去除提出了一种新的方法。     

Effects of hot-carrier stress on high performance polycrystalline silicon thin film transistor with a single perpendicular grain boundary

This paper is a report on the effect of a single perpendicular grain boundary on the hot-carrier and high current stability in high performance polycrystalline silicon (poly-Si) thin film transistors (TFTs). Under a hot carrier stress condition (Vg = Vth + 1 V, Vd = 12 V), the poly-Si TFT with a single grain boundary is superior to the poly-Si without any grain boundary because of the smaller free carriers available for electric conduction. The shift of transconductance in poly-Si TFT with a single grain boundary is less than 5% after hot carrier stress during a period of 1000 s. The shift of transconductance is about 25% in the case of the poly-Si TFTs without a grain boundary in the channel. On high current stress, the poly-Si TFT without the grain boundary is less degraded than the poly-Si TFT with the grain boundary because the concentrated electric field near the drain junction is lower.     

Pulse stabilisation in harmonically FM modelocked erbium fibre ring laser with DFBLD

A new pulse stabilisation scheme for a harmonically frequency modulated (FM) modelocked erbium fibre ring laser using a distributed feedback laser diode (DFBLD) is presented. More than 65 dB supermode noise suppression in the RF spectrum was obtained with the proposed method. Effective reduction of supermode noise can be accomplished as the DFBLD in the fibre laser acts not only as a fast-gain saturated medium but also as an optical bandpass filter for suppressing supermode noise in a harmonically modelocked laser system.     

TMS320C67系列EMIF与异步FIFO存储器的接口设计

介绍了TI公司TMS320C67系列DSP的EMIF(外部存储器接口)与异步FIFO(先进先出)存储器的硬件接口设计,着重描述了用EDMA(扩展的直接存储器访问)方式读取FIFO存储器数据的软件设计流程,最后说明了在选择FIFO存储器时应注意的问题.由于EMIF的强大功能,不仅具有很高的数据吞吐率,而且可以与不同类型的同步、异步器件进行无缝连接,使硬件接口电路简单,调试方便.运用EDMA的方式进行数据传输,由EDMA控制器完成DSP存储空间内的数据搬移,这样可以最大限度地节省CPU的资源,提高整个系统的运算速度.     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.