Preparation and characterization of modified starch‐based plastic film reinforced with short pulp fiber. II. Mechanical properties

Native corn starch‐ and hydroxypropylated starch (HPS‐) based plastic films were prepared using the short pulp fiber as the reinforcement and the glycerol as the plasticizer. The results of tensile test showed that the strain and stress at break and elastic modulus increased with pulp content. With glycerol content, the strain at break increased considerably, but the breaking stress and elastic modulus decreased. And the stress–strain curves showed that the brittleness problem of films was overcome by the pulp, glycerol, and water content. The hydroxypropyl starch films showed results similar to those of the native starch films. The results of the three‐point bending test showed that maximum deflection, flexural strength, and specific work increased with pulp content, but the flexural modulus was the highest at a pulp content of 20%. And with the glycerol content, the maximum deflection and specific work of rupture increased, but the bending elastic modulus decreased. The hydroxypropyl starch films showed results similar to those of native starch films as far as the maximum deflection and flexural strength were concerned, but the bending elastic modulus and specific work of the hydroxypropyl starch films were considerably lower than those of starch films. So it was concluded that the flexibility of films was improved by the hydroxypropylation. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2108–2117, 2003     

Advanced underfill for high thermal reliability

The key to the success of flip‐chip technology lies in the availability of sucessful underfill materials. However, the reliability of flip‐chip technology using current underfill materials is generally found to be lower than that of conventional wire‐bond connection packaging materials such as epoxy molding compound (EMC) because of the high coefficients of thermal expansion (CTE) and moisture absorption of cured underfill material. In this study desbimide (DBMI), which has a low melting point (about 80°C), was used in the underfill materials as a cohardener. As a result, DBMI‐added underfill can show excellent thermal reliability, which is due to the superior properties of the CTE, the elastic modulus, and water resistance. When the properties of a 2 wt % DBMI‐added underfill were compared with those of a typical underfill (epoxy/anhydride), the CTE value was reduced to less than one‐half at the solder reflow temperature (about 200°C), the elastic modulus was reduced to less than one‐half in the temperature region below the glass‐transition temperature, and the water resistance was improved twofold. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2617–2624, 2002     

Characterization of poly(vinylidenefluoride-co-hexafluoropropylene)-based polymer electrolyte filled with TiO2 nanoparticles

Nanoscale TiO₂ particle filled poly(vinylidenefluoride-co-hexafluoropropylene) film is characterized by investigating some properties such as surface morphology, thermal and crystalline properties, swelling behavior after absorbing electrolyte solution, chemical and electrochemical stabilities, ionic conductivity, and compatibility with lithium electrode. Decent self-supporting polymer electrolyte film can be obtained at the range of <50 wt% TiO₂. Different optimal TiO₂ contents showing maximum liquid uptake may exist by adopting other electrolyte solution. Room temperature ionic conductivity of the polymer electrolyte placed surely on the region of >10⁻³ S/cm, and thus the film is very applicable to rechargeable lithium batteries. An emphasis is also be paid on that much lower interfacial resistance between the polymer electrolyte and lithium metal electrode can be obtained by the solid-solvent role of nanoscale TiO₂ filler.     

Synthesis and luminescence properties of new blue‐light‐emitting polyconjugated poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene} polymers and copolymers

Three new soluble polyconjugated polymers, all of which emitted blue light in photoluminescence and electroluminescence, were synthesized, and their luminescence properties were studied. The polymers were poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene}, poly((9,9‐dioctylfluorene‐2,7‐diyl)‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)vinylene‐1,4‐phenylene]}) [P(DOF‐PVP)], and poly([N‐(2‐ethyl) hexylcarbazole‐3,6‐diyl]‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)]vinylene‐1,4‐phenylene}). The last two polymers had alternating sequences of the two structural units. Among the three polymers, P(DOF‐PVP) performed best in the light‐emitting diode devices of indium–tin oxide/poly(ethylenedioxythiophene) doped with poly(styrene sulfonate) (30 nm)/polymer (150 nm)/Li:Al (100 nm). This might have been correlated with the balance in and magnitude of the mobility of the charge carriers, that is, positive holes and electrons, and also the electronic structure, that is, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels, of the polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 307–317, 2006     

Properties of chitosan‐based biopolymer films with various degrees of deacetylation and molecular weights

An increase in the depolymerization of chitosan was found with an increased concentration of sodium perborate. Acetic anhydride was added to reacetylated chitosan in a molar ratio per gulcosamine unit, and the amide I band of IR spectra changed with the addition of acetic anhydride. Sixteen chitosans with various molecular weights (MWs) and degrees of deacetylation (DODs) were prepared. X‐ray diffraction patterns indicated their amorphous and partially crystalline states. Increases in the chitosan MW and DOD increased the tensile strength (TS). TS of the chitosan films ranged from 22 to 61 MPa. However, the elongation (E) of chitosan films did not show any difference with MW. TS of chitosan films decreased with the reacetylation process. However, E of chitosan films was not dependent on DOD. The water vapor permeabilities (WVPs) of the chitosan films without a plasticizer were between 0.155 and 0.214 ng m/m² s Pa. As the chitosan MW increased, the chitosan film WVP increased, but the values were not significantly different. Moreover, the WVP values were not different from low DOD to high DOD. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3476–3484, 2003     

High catalytic activity of PdOx/MnO2 for CO oxidation and importance of oxidation state of Mn

PdO_x/MnO₂ has been examined as a catalyst for CO oxidation using a conventional flow reactor at reaction temperatures between 50 and 150°C. In the reaction conditions of GHSV (gashourlyspacevelocity) of 1.22 × 10⁵/h and CO concentration of 2000 ppm, PdO_x/MnO₂ showed higher catalytic activity compared with PdO_x/Mn₂O₃, which had been previously reported as an effective catalyst due to the cooperative action of Pd and Mn₂O₃ for this reaction. The reason for higher activity of PdO_x/MnO₂ than PdO_x/Mn₂O₃ has been investigated using TPR (temperatureprogrammed reduction) and XPS studies. TPR showed that PdO_x/MnO₂ could be reduced by CO at much lower temperature than PdO_x/Mn₂O₃. During the experiment of reduction and oxidation, XPS showed that the valence of Mn in the PdO_x/MnO₂ was between 4+ and 3+, which is higher than that of Mn in the PdO_x/Mn₂O₃ catalyst of which the valence has been reported to be between 3+ and 2+. It is known that in this catalyst system the support supplies oxygen onto Pd, where the oxidation occurs with adsorbed CO, and the ability of the support to provide oxygen improves the performance of the catalyst. Therefore, it was concluded that the readiness of MnO₂ to be reduced with maintaining a higher oxidation state showed higher CO oxidation activity than Mn₂O₃ as support for PdO_x.     

Absorption of NO x in packed column (I)

A mathematical model for an absorption of nitrogen oxides into water in packed column was developed based on the mass-transfer coefficient in packed column and the chemical reaction accompanying NO _x absorption produces HNO₃ and HNO₂ in the liquid phase. The subsequent dissociation of HNO₂ in the liquid-phase results in the formation of HNO₃ and NO gas, and then this NO gas follows to be oxidized by O₂ in air. The important factors influenced on the absorption of NO _x are the oxidation state of NO gas and the partial pressure of nitrogen oxides in the gas. The efficiency of NO _x absorption increases with the increase of the partial pressure of NO _x . The most critical value for using the model is the constant of .The selection of 11×10⁻⁴kg·mol/atm·m²·sec for resonable for this model.     

Analysis of epoxidized natural rubber. A comparative study of d.s.c., n.m.r., elemental analysis and direct titration methods

A comparative analysis of epoxidized natural rubber samples by ¹H and ¹³C n.m.r., titrimetric, elemental and d.s.c. techniques has been made. Whereas the titrimetric method is only applicable at low epoxy contents (< 15 mol%) both n.m.r. methods give reasonable precision over the compositional range of 20–75 mol%. Elemental analysis appears less reliable. D.s.c. analysis through measurement of T_g provides the highest precision of measurement but requires independent calibration by one or more of the primary methods. The epoxy content may also be related to the polymer density.     

Influence of mixing cycle on the degree of mixing of calcite‐filled polyethylene upon stretching

The mixing cycle‐dependent degree of dispersion and degree of mixing of a calcite (calcium carbonate) agglomerate in high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), and linear low‐density polyethylene (LLDPE) matrices upon stretching was investigated using three different techniques: mechanical property, morphological behavior, and image analyzer analyses. The mechanical properties analyzed in terms of the tensile strength and maximum elongation resulted in that the second mixing was the best for giving a better property for all systems except the LDPE system, which exhibited no significant difference between the second and third mixings. The morphological behavior of the three compounds were different, but no distinctive difference was observed to differentiate the degree of mixing from system to system. The number‐, weight‐, and z + 1‐average diameters of the air hole and the aspect ratio upon the stretching and mixing cycle were calculated to analyze the degree of mixing of the calcite‐filled composites. As a consequence, no difference in the average diameter of the air hole was obtained among the three systems, but the aspect ratios of the air hole varied significantly. Thus, the degree of dispersion and the degree of mixing may be influenced by the average calcite agglomerate size, the average diameter of the air hole, and the aspect ratio upon stretching and mixing cycles. Those factors would be formed by the difference in chemical characteristics upon various microstructures of polyethylene and its molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 311–321, 2003     

Olfactory coding in the perception of semiochemicals

Information processing in the olfactory pathway underlying the perception of semiochemicals by insects is discussed. Both the chemical message for mates and the message for food consist of blends of chemicals. Olfactory receptors in an insect species are tuned to the detection of those compounds which comprise such chemical messages for that species. The classification of receptors as specialists or generalists coincides with two concepts of information processing, i.e., labeled lines and across-fiber patterns, respectively. The olfactory code coming from antennal receptors inPieris brassicae larvae is a combination of labeled lines and across-fiber patterning. When antennae of adult Colorado potato beetles,Leptinotarsa decemlineata, are stimulated by binary mixtures of leaf odor components, the pattern of neural activities in the olfactory receptors shows some separation into two channels, quantitative versus qualitative detection. The separation is complete in the antennal lobe of this beetle.Presented at the Symposium on Insect Chemical Communications: Unifying Concepts. ACS 194th National Meeting, New Orleans, Louisiana, August 31, 1987.