Crystallization Control in Metallurgical Slags Using the Single Hot Thermocouple Technique

With the single hot thermocouple technique (SHTT) the solidification behavior of metallurgical slags has been studied by in situ observation, constructing time–temperature–transformation (TTT) or continuous‐cooling‐transformation (CCT) diagrams. The SHTT is a unique apparatus that enables measurement of the slag sample temperature using a thermocouple while the sample is heated or cooled simultaneously. Due to the low heat capacity of the system sample/thermocouple high heating or cooling rates can be easily obtained (>3000°C/min). The following findings are reported in the present paper: (i) For the CaO–Al₂O₃ slag – 44% CaO, 56% Al₂O₃ (wt%) – the CCT diagram shows large differences between liquidus and the temperature for first crystals precipitation, even at low cooling rates, for example, 168°C below the liquidus when cooling at a rate of 6°C min^?1. (ii) For the CaO–SiO₂ slag – % CaO/% SiO₂ (wt%) = 0.7 – no crystal is observed for continuous cooling, even at low cooling rates, such as 10°C min^?1. During isothermal experiments crystallization was observed only at 1000°C with an incubation time of 76 s (average of six experiments, standard deviation 27 s). However, crystallization becomes much more intense for the CaO–SiO₂ slag when increasing the temperature after reaching lower temperatures (<1000°C), where probably the conditions for nucleation are better.     

A Ho(III) potentiometric polymeric membrane sensor based on a new four dentate neutral ion carrier

In this research, we report a new Ho^3 +-PVC membrane electrode based on N-(4,5-dimethyl-2-(picolinamido)phenyl)picolinamide (H₂Me₂bpb) as a suitable ion carrier. Poly vinylchloride (PVC)-based membrane composed of H₂Me₂bpb with oleic acid (OA) as anionic additives, and o-nitrophenyloctyl ether (NPOE) as plasticized solvent mediator. The sensor exhibits a Nernstian slope of 20.1 ± 0.2 mV decade^? 1 over the concentration range of 1.0 × 10^? 6 to 1.0 × 1^? 2 mol L^? 1, and a detection limit of 5.0 × 10^? 7 mol L^? 1 of Ho^3 + ions. The potentiometric response of the sensor is independent of the solution pH in the range of 3.5–9.4. It has a very short response time, in the whole concentration range (< 10 s), and can be used for at least eight weeks. The proposed electrode shows a good selectivity towards Ho^3 + ions over a wide variety of cations, including alkali, alkaline earth, transition and heavy metal ions. To assess its analytical applicability the proposed Ho^3 + sensor was successfully applied as an indicator electrode in the titration of Ho^3 + ion solutions in certified reference materials, alloy samples and for the determination of the fluoride ion in two mouthwash preparations.     

Coherent multicarrier technology for implementation in the customeraccess

The use of coherent multicarrier (CMC) techniques in the integrated broadband communication network (IBCN) is proposed. Technology, implementation strategies, system engineering, system application areas, and evolution aspects are considered. The use of CMC systems for distributive and interactive services is discussed, and related CMC transmission and switching issues are considered. Details on the realization of a CMC demonstrator for a customer access and plans for implementation of the engineered equipment in field trials are presented     

Concentrations of fluoride in wines from the Canary Islands.

Potentiometry using an ion-selective electrode has widely been used for determining fluoride because of its simplicity and rapidity. The concentration of fluoride was determined (Gran's method) in 70 wines from the main wine-producing regions of the Canary Islands. The mean concentration of fluoride in wines from a region with a high concentration of fluoride in drinking waters was significantly (p < 0.05) higher than those mean concentrations obtained in the remaining wines. Non-important differences were found among the types of wine analysed. However, the fluoride concentrations of all the Canarian wines analysed here did not present a risk for the public health.     

A PROBABILISTIC MODEL FOR THE MODIFIED CLAUS PROCESS

A model is proposed for simulation of an industrial Claus unit with a straight-through configuration and two catalytic reactors. Process design evaluation based on deterministic calculations does not take into account the uncertainties associated with the input variables. The probabilistic simulation method was applied in the Claus model to obtain an impression of how some of these inaccuracies influence plant performance. The application was tested experimentally to confirm its validity, then used for control purposes.     

AN EXPERIMENTAL INVESTIGATION ON WEAR ASPECTS OF TAPPING OPERATION ON HARDENED STEELS

Tapping is one of the most intensively used operations for internal threads with diameters below about 15 mm. When a tap fails, the workpiece has a significant added value. The present work investigates some aspects of wear and performance when solid carbide coated taps M10 × 1.5 cut hardened AISI H13 and AISI D2. The results indicated that it was possible to make threads on hardened AISI D2, although the number of holes was essentially low and tool breakage was often. Threads on hardened AISI H13 was possible with reasonably low tool wear. Cutting surface presented some indication of small flaws due to the adhered material on the taps.     

New tractable classes for default reasoning from conditional knowledge bases

This paper refines the tractability/intractability frontier of default reasoning from conditional knowledge bases. It presents two new tractable cases with relation to lexicographic entailment. In particular, we have introduced nested conditional knowledge bases and co-nested conditional knowledge bases, which are meaningful conditional knowledge bases. Both tractable classes presented in this paper can be recognized in linear time.     

Depletion of enteroendocrine and mucus‐secreting cells is associated with colorectal carcinogenesis severity and impaired intestinal motility in rats

This study investigated the relationship between enteroendocrine and mucus‐secreting cells distribution, the severity of colonic mucosal injury and intestinal motility in experimental colorectal carcinogenesis. Using a standardized murine model of colorectal carcinogenesis, eight‐weeks‐old female Wistar rats weighting 147.30 ± 29.15g were randomized into two groups receiving a subcutaneous injection of 0.9% saline (control) or the chemical carcinogen 1,2‐dimethylhydrazine (DMH) at 20 mg/kg per week during 10 weeks. Aberrant crypt foci (ACF) were more frequent in DMH group compared to control group (P < 0.001). The number of enteroendocrine and mucus‐secreting cells, and intestinal motility was reduced in DMH animals (P < 0.05). The distribution of enteric neurons was similar in both groups. In DMH animals there was a direct correlation between colonic motility and distribution of enteroendocrine (R² = 0.68, P < 0.05) and mucus‐secreting cells (R² = 0.77, P < 0.05). Inverse correlation between the number of ACF, mucus‐secreting cells (R² = ?0.57, P < 0.05), and enteroendocrine cells (R² = ?0.74, P < 0.05) was also observed. There was inverse correlation between the severity of the mucosal lesion, the number of mucus‐secreting cells (R² = ?0.83, P < 0.05) and enteroendocrine cells (R² = ?0.96, P < 0.05). There was a direct correlation between nucleolar organizer regions (AgNOR) and ACF number (R² = 0.62; P < 0.01). Inverse correlation was also found between AgNOR, the number of mucus‐secreting cells (R² = ?0.76; P < 0.001), and enteroendocrine cells (R² = ?0.86; P < 0.001). Taken together, the results indicated that colonic malignant transformation is related to depletion of mucus‐secreting and enteroendocrine cells, which was a useful indicator of the evolutionary status of intestinal neoplasm, partially explaining the intestinal motility disorders in the early stages of colorectal carcinogenesis. Microsc. Res. Tech. 79:3–13, 2016. © 2015 Wiley Periodicals, Inc.     

Cytocompatibility,physical properties,and antibiofilm activity of endodontic sealers with amoxicillin

The aim was to evaluate the cytocompatibility of the AH Plus and Sealapex associated with amoxicillin (AA) in a quantity of 10% by total weight of the sealers, the flow and setting time of these sealers with 10%‐0.25% AA and antibiofilm activity of these sealers associated with AA in a concentration that does not alter their physical properties (1%). Cytocompatibility was assessed by MTT, neutral red and cytoskeletal fluorescence assays. Setting time and flow was evaluated using the specifications of ISO 6876/2012. For the antibiofilm evaluation, materials were placed in direct contact with E. faecalis biofilm induced on dentin blocks. The incorporation of AA into the sealers did not diminish the viability of the fibroblasts and did not cause structural changes in the cytoskeletal. The flow of AH Plus + AA at 1.0; 0.5 and 0.25%, and of Sealapex + AA at 5.5; 2.5; 1.0; 0.5 and 0.25% were within the specifications of the ISO 6876. AH Plus, and AH Plus + AA at 1.0; 0.50 and 0.25% presented a setting time of 730, 439, 455, and 474 min., respectively. Sealapex ‐ pure or associated with AA did not set completely. The addition of 1% AA to the sealers did not increase their antibiofilm activity. It was concluded that the incorporation of 10% AA caused no toxic effects on fibroblasts, but harmed the physical properties. The addition of AA in concentration that does not affect the physical properties of the sealers did not increase their antibiofilm activity.     

Influence of Spray-Drying Conditions on Physical and Morphological Characteristics of Microencapsulated Benzoic Acid

Benzoic acid is widely used as a preservative in the food and feed industry, and microencapsulation is important in the application of this ingredient in various food products. The objective of this work was to evaluate the effect of benzoic acid concentration and drying air temperature on the physical characteristics of powders produced by spray drying, using maltodextrin and modified starch as the wall materials. A rotatable central composite design was used; the independent variables were inlet air temperature (145–180 °C) and benzoic acid concentration (2–10 %, m/m). Maximum yield was obtained when higher concentrations of benzoic acid and higher inlet air temperatures were applied. The highest microencapsulation efficiency was reached at intermediate temperatures (160 °C) and low concentration of benzoic acid. The particles size (D _[4,3]) ranged from 24.99 to 29.52 μm and, in general, presented amorphous structure, spherical shape with rough surfaces and had no cracks The optimum condition, considering all the response variables together, was drying air temperature 169 °C and benzoic acid concentration 6 % (m/m). Under these conditions, the particles presented solubility of 75.96 g/100 g and wettability of 56.8 s/g. Moreover, the process showed microencapsulation efficiency of 76.77 g/100 g and yield of 40.1 %. Spray drying was considered a potential process to provide microencapsulated benzoic acid.