Study of variables affecting the synthesis of biodiesel from Madhuca Indica oil

Biodiesel derived from non‐edible Madhuca Indica oil (MIO) seems to be a better alternative to diesel oil in India. In the present work, effects of reaction variables such as mass ratio of methanol to oil, catalyst concentration, reaction time and reaction temperature on biodiesel yield were studied. The acid value of the commercially available MIO is high, and hence a two‐step process was used to produce biodiesel from MIO. In the first step, the acid value of the MIO was reduced to less than 1 mg KOH/g, using acid‐catalyzed transesterification. In the second step, the pretreated MIO was converted to biodiesel using alkaline‐catalyzed transesterification. From the experimental results, it is observed that the optimized conditions for biodiesel production are a 1 : 4 mass ratio of methanol to oil, 55 °C reaction temperature, 120 min of reaction time, and 1% sodium hydroxide catalyst. The properties of the MIO biodiesel were found to be within the biodiesel limits of the European Union. Hence, the MIO biodiesel can be used as a substitute for diesel for the sustainable development of rural areas and as a renewable fuel.     

Direct torque control of induction motor based on advanced discontinuous PWM algorithm for reduced current ripple

In recent years several discontinuous pulse width modulation (DPWM) methods are reported to improve the performance of AC drives at high modulation indices. It is proved that the performance of the popular PWM methods is modulation index dependent and no single DPWM method provides satisfactory performance over the entire high modulation range. Two popular existing DPWM methods renowned with the names DPWMMIN, DPWMMAX clamp each phase for 120° duration in every cycle of its fundamental voltage. It is observed that only the zero state is different in these two sequences. In this paper, it is proposed that, utilizing these two DPWM sequences and by changing the zero state at any spatial angle γ, where γ is between 0° and 60°, an infinite number of DPWM sequences including the existing DPWM methods and advanced DPWM (ADPWM) methods can be generated which are categorized as “continual clamping” and “split clamping” sequences. Using these ADPWM techniques an optimal split clamping sequence-based DTC of induction motor is proposed. With the proposed DTC method it is shown that steady state line current distortion at higher line side voltages is reduced significantly compared with the CDTC as well as conventional SVPWM (CSVPWM)-based DTC.     

Fabrication of copper–TiC–graphite hybrid metal matrix composites through microwave processing

The significant requirements such as wear resistance and better tribological properties in addition to good electrical conductivity necessitate the development of copper-based advanced metal matrix composites for electrical sliding contact applications. Though the addition of graphite to copper matrix induces self-lubricating property, the strength of the composite reduces. The improvement in the strength of the composite can be achieved by reinforcing harder ceramic particles such as SiC, TiC, and Al₂O₃. In this paper, the development of hybrid composite of copper metal matrix reinforced with TiC and graphite particles through microwave processing was investigated. The effects of TiC (5, 10, and 15 vol.%) and graphite (5 and 10 vol.%) reinforcements on physical and mechanical properties of microwave-sintered copper–TiC–graphite hybrid composites are discussed in detail. Micrographs show the uniform distribution of reinforcements in copper matrix. Microwave-sintered composites exhibited higher relative density, sintered density, and hardness compared with conventionally sintered ones.     

Temporal and spectral characteristics of aerosol optical depths in a semi-arid region of southern India

The spectral and temporal variations of aerosol optical depths (AOD) observed over Anantapur (a semi-arid region) located in the Southern part of India are investigated by analyzing the data obtained from a Multiwavelength Solar Radiometer (MWR) during January 2005-December 2006 (a total of 404 clear-sky observations) using the Langley technique. In this paper, we highlighted the studies on monthly, seasonal and spectral variations of aerosol optical depth and their implications. The results showed seasonal variation with higher values during pre-monsoon (March-May) and lower in the monsoon (June-November) season at all wavelengths. The pre-monsoon increase is found to be due to the high wind speed producing larger amounts of wind-driven dust particles. The post-monsoon (December-February) AOD values decrease more at higher wavelengths, indicating a general reduction in the number of bigger particles. Also during the post-monsoon, direction of winds in association with high or low pressure weather systems and the air brings more aerosol content to the region which is surrounded by a number of cement plants, lime kilns, slab polishing and brick making units. The quantity of AOD values in pre-monsoon is higher (low during post-monsoon) for wavelength, such as shortwave infrared (SWIR) or near infrared (NIR), which shows that coarse particles contribute more compare with the sub-micron particles. The composite aerosols near the surface follow suit with the share of the accumulation mode to the total mass concentration decreasing from ~ 70% to 30% from post-monsoon to pre-monsoon. Coarse mode particle loading observed to be high during pre-monsoon and accumulation mode particles observed to be high during post-monsoon. The backward trajectories at three representative altitudes with source point at the observing site indicate a possible transport from the outflow regions into Bay of Bengal, southern peninsular India and Arabian Sea. The temporal variations of AOD, Angstrom wavelength exponent and precipitable water content over Anantapur have also been compared with those reported from selected locations in India.     

海枣核CO2活化和磷酸活化制备活性炭及其结构、吸附性能（英文）

由于具有很大的吸附容量,多孔炭材料是优良的吸附剂。笔者试图比较海枣核分别经CO2活化和磷酸活化所制活性炭的结构和吸附性能。活化过程和工艺条件对炭的物理化学性质影响较大,根据文献报道的结果选取了优化的工艺参数。基于氮气吸附等温线、SEM、FT-IR等分析结果,评估了活性炭的结构特征,吸附性能则由亚甲蓝吸附值表示。CO2活化得到了微孔活性炭,产率为44%、BET比表面积是666 m2·g-1;磷酸活化得到了产率为14.8%的中孔活性炭,BET比表面积为725 m2·g-1。CO2活化活性炭的平均孔径是1.51 nm,磷酸活化活性炭的则为2.91 nm。活性炭的亚甲蓝吸附等温线分别用Langmuir等温线和Freundlich等温线进行了验证,在优化工艺条件下制备的CO2活化炭和磷酸活化炭的亚甲蓝w单分子吸附容量分别为110 mg·g-1和345 mg·g-1。然而,磷酸活化产生的亚甲蓝吸附值最高达455 mg·g-1。     

Site-specific stamping of graphene micro-patterns over large areas using flexible stamps

Site-specific stamping has the potential of becoming a low-cost, high-throughput method for depositing specific-shaped graphene micro-patterns over large areas on a wide variety of substrates. The use of an approach involving flexible stamps presented here represents an important advance towards reaching that potential. This approach entails lithographic creation (dry etching) of high-quality micro-pillar arrays of highly oriented pyrolytic graphite (HOPG) over large areas. This is followed by embedding the micro-pillar arrays in polydimethylsiloxane (PDMS), and detaching them from the HOPG base. This results in flexible stamps containing embedded HOPG micro-pillar arrays with freshly cleaved stamping surfaces. The flexible HOPG/PDMS stamps are then brought into contact with substrate surfaces to site-specifically stamp graphene or few-layer graphene (FLG) arrays over large areas. The freshly cleaved nature of the micro-pillar surfaces in the flexible stamps, the low elastic modulus of the flexible stamps and the elimination of sidewall deposits on the micro-pillars allow for more uniform stamping, relative to the use of stiff HOPG stamps from earlier studies. This approach has the potential to expand the substrate choice for graphene or FLG stamping to include curved and/or flexible substrates that could have an impact on the burgeoning field of flexible/stretchable electronics.     

Minimally invasive injectable short nanofibers of poly(glycerol sebacate) for cardiac tissue engineering

Myocardial tissue lacks the ability to appreciably regenerate itself following myocardial infarction (MI) which ultimately results in heart failure. Current therapies can only retard the progression of disease and hence tissue engineering strategies are required to facilitate the engineering of a suitable biomaterial to repair MI. The aim of this study was to investigate the in?vitro properties of an injectable biomaterial for the regeneration of infarcted myocardium. Fabrication of core/shell fibers was by co-axial electrospinning, with poly(glycerol sebacate) (PGS) as core material and poly-l-lactic acid (PLLA) as shell material. The PLLA was removed by treatment of the PGS/PLLA core/shell fibers with DCM:hexane (2:1) to obtain PGS short fibers. These PGS short fibers offer the advantage of providing a minimally invasive injectable technique for the regeneration of infarcted myocardium. The scaffolds were characterized by SEM, FTIR and contact angle and cell-scaffold interactions using cardiomyocytes. The results showed that the cardiac marker proteins actinin, troponin, myosin heavy chain and connexin 43 were expressed more on short PGS fibers compared to PLLA nanofibers. We hypothesized that the injection of cells along with short PGS fibers would increase cell transplant retention and survival within the infarct, compared to the standard cell injection system.     

Structures and performances of simultaneous ultrasound and alkali treated oil palm empty fruit bunch fiber reinforced poly(lactic acid) composites

In this study composites were produced using extrusion followed by injection molding with alkali and ultrasound treated oil palm empty fruit bunch (EFB) fibers with poly(lactic acid). The fiber content, alkali solution concentration, exposing time and treatment temperature were optimized. The optimized EFB fibers were treated with hyper branched polyester solution. The composites were characterized by tensile testing, impact testing, scanning electron microscopy, thermogravimetric analysis, differential scanning calorimetry and Fourier transformation infra-red spectroscopy. A significant increase in mechanical and interfacial properties was found for composites due to simultaneous alkali and ultrasound treatment.     

Epitaxial Ni?Mn?Ga Films for Magnetic Shape Memory Alloy Microactuators

Active materials such as piezoelectrics are established in the field of microsystems application despite their low achievable strains which often require the integration of additional gear mechanisms. The ongoing search for new active materials has focused on magnetic shape memory (MSM) alloys such as Ni? Mn? Ga since they combine macroscopic strains of up to 10% with a cycling frequency well above the frequencies of conventional thermal shape memory alloys. The present review focuses on preparation and analysis of Ni? Mn? Ga films that can eventually be integrated in microsystems. Single crystal like films are prepared by epitaxial growth on suitable substrate materials. Since the magnetically induced reorientation of variants is blocked by a rigid substrate, we present different methods for releasing films from the substrates. We show that the sacrificial layer technology is the most promising approach. Further processing of the freestanding film requires a microtechnology which is adjusted to the film laminate structure. The properties of the freestanding films are compared with films on a rigid substrate. Although we observe stress‐induced twin boundary motion, the twinning stress is too high to be overcome by an external magnetic field. Therefore, it is necessary to develop suitable training methods to reduce the twinning stress below 2 MPa to enable the activation of the material by means of an external magnetic field.     

3D nanoporous nanowire current collectors for thin film microbatteries

Conventional thin film batteries are fabricated based on planar current collector designs where the high contact resistance between the current collector and electrodes impedes overall battery performance. Hence, current collectors based on 3D architectures and nanoscale roughness has been proposed to dramatically increase the electrode-current collector surface contact areas and hence significantly reduce interfacial resistance. The nanorod-based current collector configuration is one of several 3D designs which has shown high potential for the development of high energy and high power microbatteries in this regard. Herein we fabricate a nanoporous nanorod based current collector, which provides increased surface area for electrode deposition arising from the porosity of each nanorods, yet keeping an ordered spacing between nanorods for the deposition of subsequent electrolyte and electrode layers. The new nanostructured 3D current collector is demonstrated with a polyaniline (PANI)-based electrode system and is shown to deliver improved rate capability characteristics compared to planar configurations. We have been able to achieve stable capacities of ~32 μAh/cm(2) up to 75 cycles of charge/discharge even at a current rate of ~0.04 mA/cm(2) and have observed good rate capability even at high current rates of ~0.8 mA/cm(2).