Effect of Twin-Plane Reentrant Edge on the Coarsening Behavior of Barium Titanate Grains

When BaTiO₃ ceramics were sintered at relatively low temperatures (≤1250°C), the grains with reentrant edges caused by a (111) double twin grew exclusively. As a result, a microstructure with a bimodal grain-size distribution composed of platelike large grains and fine matrix grains was obtained. In contrast, at the usual sintering temperature between 1250° and 1350°C, grains containing a (111) double twin did not exhibit any growth advantage. In this case, a coarse and uniform microstructure was obtained. When this coarse-grained specimen was further heat-treated at 1365°C, the grains possessing a double twin were observed to grow exclusively again. The results were explained in terms of a coarsening process controlled by two-dimensional nucleation.     

Preparation and Characterization of 17O-Enriched Alumina for Nuclear Fusion Damage Experiments

Alumina enriched in ¹⁷O was successfully fabricated from aluminum isopropoxide and water containing the ¹⁷O isotope. This material was necessary for an experiment to study the radiation damage expected in alumina exposed to a nuclear fusion reactor environment. The enrichment levels of specimens subjected to different preparation schedules were measured using a nuclear reaction analysis technique. Replacement of the ¹⁷O isotope in the ceramic by atmospheric oxygen occurred readily. Therefore, successful fabrication of suitably enriched alumina specimens required that all processing steps be performed under vacuum or inertgas environments. The optimum fabrication procedure produced enriched alumina specimens of >99.5% of theoretical density, ∽10-μm grain size, and a flexural strength of 280 MPa.     

Enhanced surface morphologies of screen-printed carbon nanotube films by heat treatment and their field-emission properties

A heating process for obtaining free-standing carbon nanotube emitters is presented with the aim of improving field-emission properties from the screen-printed multiwalled carbon nanotube (MWCNT) films. Using an atmosphere with an optimum combination of nitrogen and air for heat treatment of CNT films, the CNT emitters can be made to protrude from the surface. This allows for a high emission current and the formation of very uniform emission sites without special surface treatment. The morphological change of the CNT film by this technique has eliminated additional processing steps, such as surface treatment which may result in secondary contamination and damage to the film. Despite its simplicity the process provides a high reproducibility in emission current density which makes the films suitable for practical applications.     

S＆W超选择性裂解炉分区裂解探讨

介绍了S＆W超选择性裂解炉分区裂解改造的情况，包括分区裂解炉的运行情况、对后系统的影响、对产品收率的影响、投用过程存在的问题及处理。指出分区裂解能提高装置的生产能力，而产品的收率基本不变。     

Preparation of pH‐sensitive poly(vinyl alcohol‐g‐methacrylic acid) and poly(vinyl alcohol‐g‐acrylic acid) hydrogels by gamma ray irradiation and their insulin release behavior

A series of pH‐responsive hydrogels were studied as potential drug carriers for the protection of insulin from the acidic environment of the stomach before releasing in the small intestine. Hydrogels based on poly(vinyl alcohol) networks grafted with acrylic acid or methacrylic acid were prepared by a two‐step process. Poly(vinyl alcohol) hydrogels were prepared by gamma ray irradiation (50 kGy) and then followed by grafting either acrylic acid or methacrylic acid onto these poly(vinyl alcohol) hydrogels with subsequent irradiation (5–20 kGy). These graft hydrogels showed pH‐sensitive swelling behavior and were used as carriers for the controlled release of insulin. The in vitro release of insulin was observed for the insulin‐loaded hydrogels in a simulated intestinal fluid (pH 6.8) but not in a simulated gastric fluid (pH 1.2). The release behavior of insulin in vivo in a rat model confirmed the effectiveness of the oral delivery of insulin to control the level of glucose. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 636–643, 2004     

Synthesis, structure and magnetic properties of β-MnO 2 nanorods

We present synthesis, structure and magnetic properties of structurally well-ordered single-crystalline β-MnO₂ nanorods of 50–100 nm diameter and several μm length. Thorough structural characterization shows that the basic β-MnO₂ material is covered by a thin surface layer (∼2.5 nm) of α-Mn₂O₃ phase with a reduced Mn valence that adds its own magnetic signal to the total magnetization of the β-MnO₂ nanorods. The relatively complicated temperature-dependent magnetism of the nanorods can be explained in terms of a superposition of bulk magnetic properties of spatially segregated β-MnO₂ and α-Mn₂O₃ constituent phases and the soft ferromagnetism of the thin interface layer between these two phases.     

Artificial neural network approaches on composition-property relationships of jet fuels based on GC-MS

The relationships of composition-properties of 80 jet fuels concerning chemical compositions and several specification properties including density, flashpoint, freezing point, aniline point and net heat of combustion were studied. The chemical compositions of the jet fuels were determined by GC-MS, and grouped into eight classes of hydrocarbon compounds, including n-paraffins, isoparaffins, monocyclopraffins, dicyclopraffins, alkylbenzens, naphthalenes, tetralins, hydroaromatics. Several quantitative composition-property relationships were developed with three artificial neural network (ANN) approaches, including single-layer feedforward neural network (SLFNN), multiple layer feedforward neural network (MLFNN) and general regressed neural network (GRNN). It was found that SLFNNs are adequate to predict density, freezing point and net heat of combustion, while MLFNNs produce better results as far as the flash point and aniline point prediction are concerned. Comparisons with the multiple linear regression (MLR) correlations reported and the standard ASTM methods showed that ANN approaches of composition-property relationships are significant improvement on MLR correlations, and are comparable to the standard ASTM methods.     

Numerical study of coal particle cluster combustion under quiescent conditions

Behavior of ignition and combustion of coal particle cluster under a quiescent condition was numerically simulated by solving balance equations of mass and enthalpy with combustion kinetic models of volatiles and char. Two-flame structure, one flame penetrating into the cluster and the other moving out of the cluster, was predicted during the combustion of coal particle cluster. Effects of radiative heat transfer, group number, ambient temperature, coal particle size, and oxygen concentration on ignition and combustion of coal particle clusters were also analyzed. Simulations indicated that the gas volume fraction of coal particle cluster increases with time after devolatilization. Gas velocity passing through the cluster surface varied significantly at volatile liberation. The ignition time delay was reduced with the increase of ambient temperature. The cluster devolatilization rate and char burning rate increased while the ignition time delay decreased with the increase of ambient oxygen concentration.     

Characterization of polyisoprene-clay nanocomposites prepared by solution blending

The effects of clay dispersion and the interactions between clays and polymer chains on the viscoelastic properties of polymer/clay nanocomposites are investigated using oscillatory shear rheology, X-ray diffraction (XRD), small-angle X-ray scattering (SAXS), and transmission electron microscopy (TEM). Four different montmorillonite silicates of natural clays, plasma-treated clays, and organically modified clays (OCs) have been used in this study. For the polyisoprene (PI)/clay nanocomposites, the exfoliation of the OC dispersed in the PI matrix is confirmed with XRD and SAXS although TEM images show both exfoliated and non-exfoliated nanoclay sheets. In contrast aggregation or intercalation is obtained for the other PI/clay composites studied here. Additionally, the effective maximum volume packing fraction of OC for the exfoliated nanocomposites is determined from the overlapping of dynamic viscosity at low frequency regime, in which the effective maximum volume packing fraction is larger than the percolation threshold determined from the storage modulus of the nanocomposites.     

Preparation and characterization of polypropylene/layered silicate nanocomposites using an antioxidant

Polypropylene (PP)/layered silicate nanocomposites were prepared via simple melt mixing of three components, PP, layered silicates modified with octadecylamine (C18-MMT) and antioxidant, to investigate the role of antioxidant. TEM and X-ray scattering results confirmed the intercalated state of silicates in PP/layered silicate nanocomposites with antioxidant. In rheological and mechanical study, the nanocomposites with antioxidant showed higher properties than those of the unfilled PP. The nanocomposite with 5 wt% C18-MMT and 0.5 phr antioxidant exhibited about 1.4 times higher tensile modulus and 1.3 times higher storage modulus than the unfilled PP. However, PP/C18-MMT without antioxidant showed lower rheological values owing to the thermal decomposition of PP and the poor compatibility between PP and C18-MMT. It could be concluded that antioxidants played an important role in enhancing the compatibility between PP and C18-MMT. According to the real time X-ray diffraction, the nanocomposite showed the weak ordering of PP crystals than the unfilled PP in the load-extension plateau region of elongation.