Spray Pyrolysis of Fe3O4–BaTiO3 Composite Particles

Fe₃O₄–BaTiO₃ composite particles were successfully prepared by ultrasonic spray pyrolysis. A mixture of iron(III) nitrate, barium acetate and titanium tetrachloride aqueous solution were atomized into the mist, and the mist was dried and pyrolyzed in N₂ (90%) and H₂ (10%) atmosphere. Fe₃O₄–BaTiO₃ composite particle was obtained between 900° and 950°C while the coexistence of FeO was detected at 1000°C. Transmission electron microscope observation revealed that the composite particle is consisted of nanocrystalline having primary particle size of 35 nm. Lattice parameter of the Fe₃O₄–BaTiO₃ nanocomposite particle was 0.8404 nm that is larger than that of pure Fe₃O₄. Coercivity of the nanocomposite particle (390 Oe) was much larger than that of pure Fe₃O₄ (140 Oe). These results suggest that slight diffusion of Ba into Fe₃O₄ occurred.     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

Generation of disk-like domains with nanometer scale thickness in merocyanine dye LB film induced by hydrothermal treatment

We have characterized the binary LB films of merocyanine dye (MS) and arachidic acid (C₂₀) before and after hydrothermal treatment (HTT), which is defined as a heat treatment under relative humidity of 100%, focusing on the morphology studied by bright field (BF) microscopy and fluorescence (FL) microscopy. BF microscopy observation has revealed that the as-deposited MS-C₂₀ binary LB film is found to emit intense red fluorescence over the whole film area by 540-nm excitation. Since the surface image is almost featureless, it is considered that the crystallite sizes of J-aggregate are less than 10 μm. Interestingly, after HTT, round-shaped domains are observed in the LB systems, and the sizes are reaching 100 μm in diameter. Crystallites of J-aggregate, which are bluish in color and emit intense red fluorescence, tend to be in the round domains. We have observed two different types of domains, i.e., blue-rimmed domains and white-rimmed domains, which are postulated to be confined in the inner layers and located at the outermost layer, respectively. The thickness of the domains is equal to or less than that of the double layer of the MS-C₂₀ mixed LB film, which is ca. 5.52 nm. The molecular order of MS in the J-aggregate is improved by the HTT process leading to the significant sharpening of the band shape together with the further red shift of the band (from 590 to 594 nm up to 597 to 599 nm). The reorganized J-band is considered to be ‘apparently’ isotropic owing to the random growth of the J-aggregate in the film plane. We consider that the lubrication effect by the presence of water molecules predominates in the HTT process.     

Effect of the t–m transformation morphology and stress distribution around the crack path on the measured toughness of zirconia ceramics: A case study on Ce-TZP/alumina nanocomposite

The t–m transformation zone and related residual stress fields around two types of crack used for toughness measurements, i.e. SEVNB (arrested crack induced by a V-notch) and IF methods (indentation crack induced by a Vickers impression), are reported for a Ce-TZP/Al₂O₃ nanocomposite, in comparison with 3Y-TZP. The fact that Ce-TZP/Al₂O₃ exhibits significant high toughness value on occasions when evaluated by the IF method was determined to be clearly linked to the presence of wide ranged three-dimensional transformation configuration and resulting substantial compressive residual stress fields. In contrast, for 3Y-TZP, transformation behaviors around the two types of crack were quite similar, which proves that 3Y-TZP shows near toughness values for both SEVNB and IF methods.     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

Effect of helix-coil transition on association behavior of both-ends hydrophobically-modified water-soluble polypeptide

Dodecyl and dodecanoyl groups (C12) are attached at the chain ends of poly[N⁵-(2-hydroxyethyl) l-glutamine] (PHEG), and association behavior of this both-ends hydrophobically modified water soluble polypeptide (C12-PHEG-C12) has been investigated by means of light scattering measurements. Water/ethylene glycol (EG) mixed solvents were used as selective solvent for PHEG block, and PHEG changed its structure from random-coil state to α-helix with increasing EG content in the mixed solvent (W_EG). When W_EG is less than 0.5, flower-like micelle with C12 associated core and PHEG corona in loop conformation was suggested to be formed. Increase of W_EG from 0.5 to 0.6 induced drastic increase of association number and size of the associate, in which many C12 associated cores may be connected by PHEG in bridge conformation. This structure change of associate is considered to be driven by the increase of helix content of PHEG with W_EG, which enhances the possibility to form bridge conformation because of its rigidity. Solution preparation method, i.e. order of addition of solvent, was found to influence the structure of associate, although its effect on the helix content of PHEG was negligible.     

Effects of Annealing on Dielectric Loss and Microstructure of Aluminum Nitride Ceramics

The effect of annealing on tan δ and microstructures of aluminum nitride (AlN) ceramics were explored. Yttria was added as a sintering additive to AlN powders, and the powders were pressureless-sintered at 1900°C for 2 h in a nitrogen flow atmosphere. In succession to sintering, AlN samples were annealed at 720, 970 and 1210°C for 2 and 4 h. Very low tan δ values between 2.6 and 6.0 × 10⁻⁴ at 28 GHz were obtained when the AlN samples were annealed for 4 h at all the annealing temperatures.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Mechanical and physical properties of epoxy composites reinforced by vapor grown carbon nanofibers

Epoxy/vapor grown carbon nanofiber composites (VGCF) with different proportions of VGCF were fabricated by the in situ process.The VGCFs were well dispersed in both of the low and high viscosity epoxy matrices, although occasional small aggregates were observed in a high viscosity epoxy of 20 wt.%. The dynamic mechanical behavior of the nanocomposite sheets was studied. The storage modulus and the glass transition temperature (T_g) of the polymer were increased by the incorporation of VGCFs.The electrical and mechanical properties of the epoxy-VGCFs nanocomposite sheets with different weight percentages of VGCFs were discussed. The results were that both had maximum tensile strength and Young’s modulus at 5 wt.% for both materials and reduced the fracture strain with increasing filler content. The electrical resistivity was decreased with the addition of filler content. Mechanical, electrical and thermal properties of low viscosity epoxy composites were resulted better than that of the high viscosity composites.     

Comparison of activities in selective catalytic reduction of NOx by C3H8 over Co/MFI, Fe/MFI, and H/MFI zeolite catalysts

The Co/MFI(SiO₂/Al₂O₃ = 30) were prepared by a precipitation method with NaOCl in alkali solutions exhibited high activities to N₂ at 250 °C for the selective catalytic reduction (SCR) of NO_x. These catalysts showed two UV–vis bands at 700 and 400 nm, indicating the presence of octahedral Co(III) as well as tetrahedral Co(II). The high SCR activity over such Co(III, II)/MFI(30) seems to come from Co(III)---O moieties. The Co(II)MFI(30) catalysts prepared from Co(II)Cl₂ exhibited low SCR activities due to the presence of tetrahedral Co(II) ions in MFI. Less CO formation occurred over Co/MFI catalysts. The Fe/MFI(30) catalyst exhibited high activity due to the presence of some Fe---O species in MFI but more amount of CO were produced during SCR. H/MFI(30) catalyst exhibited a good SCR activity. However, more amount of carbonaceous deposits were produced on it. The correlation between acid concentration and SCR activity was discussed over H/MFIs.