Manipulation of microenvironment with a built-in electrochemical actuator in proximity of a dissolved oxygen microsensor

Biochemical sensors for continuous monitoring require dependable periodic self diagnosis with acceptable simplicity to check its functionality during operation. An in-situ self-diagnostic technique for a dissolved oxygen microsensor is proposed in an effort to devise an intelligent microsensor system with an integrated electrochemical actuation electrode. With a built-in platinum microelectrode that surrounds the microsensor, two kinds of microenvironments, called the oxygen-saturated or oxygen-depleted phases, can be created by water electrolysis, depending on the polarity. The functionality of the microsensor can be checked during these microenvironment phases. The polarographic oxygen microsensor is fabricated on a flexible polyimide substrate (Kapton) and the feasibility of the proposed concept is demonstrated in a physiological solution. The sensor responds properly during the oxygen-generating and oxygen-depleting phases. The use of these microenvironments for in-situ self-calibration is discussed to achieve functional integration, as well as structural integration, of the microsensor system.     

On-line dead-time compensation method using disturbance observer

A new on-line dead-time compensation method for a permanent magnet (PM) synchronous motor drive is proposed. Using a simple disturbance observer without any additional circuit and off-line experimental measurement, disturbance voltages in the rotor reference dq frame caused by the dead time and nonideal switching characteristics of power devices are estimated in an on-line manner and fed to voltage references in order to compensate the dead-time effects. The proposed method is applied to a PM synchronous motor drive system and implemented by using software of a digital signal processor (DSP) TMS320C31. Simulations and experiments are carried out for this system and the results well demonstrate the effectiveness of the proposed method.     

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO2 for no reduction by NH3

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO₂ for NO reduction by NH₃ was examined in a fixed-bed flow reactor. The deactivation of the catalyst was strongly dependent on reaction temperature. At high reaction temperatures over 300°C, the catalyst did not lose its initial activity up to 50 h of operation, regardless of SO₂ feed concentration from 500 to 20,000 ppm. However, at low reaction temperatures near 250°C, apparent deactivation did occur. Changes in the physicochemical properties such as surface area and sulfur content of deactivated catalyst well correlated with catalyst activity, depending upon reaction temperatures. The deactivation was due to pore blocking and/or filling by deactivating agents, which plugged and/or filled the pores of catalyst. The deactivating agents deposited on the catalyst surface were presumed to be (NH₄)₂SO₄ and/or (NH₄)HSO₄ from the results of TGA and ion-chromatography measurement.     

Using thermally stimulated currents to find defective capacitors

BaTiO₃ multilayer capacitors with a nominal capacitance of 3.5nF have been carefully measured using the thermally stimulated current (TSC) technique. When a 300V polarization voltage is applied at room temperature, a new TSC peak appeared in defective sample A after it has been immersed in water. No new peak was found in good-quality sample B after a similar treatment. The accelerated life test shows that sample A hasa much shorter life than sample B in terms of insulation resistance.     

山洪灾害预警准确度与及时度研究

山洪灾害预警准确度与及时度是一对相互矛盾而又联系的重要指标。文章通过对这两项指标的研究和对引发灾害的降雨强度、降雨以及灾害发生的时间资料进行分析,从而获取预警系统建设的基本技术要点和参数,对把握山洪灾害预警系统的设计定位、启用时机和作用评估具有重要作用和意义。     

Parathion degradation and toxicity reduction in solar photocatalysis and photolysis.

The solar photocatalytic degradation of methyl parathion was investigated using a circulating TiO2/solar light reactor. Under solar photocatalysis condition, parathion was more effectively degraded than solar photolysis and TiO2-only conditions. With solar photocatalysis, 20 mg/L of parathion was completely degraded within 60 min with a TOC decrease of 63% after 150 min. The main ionic byproducts during photocatalysis recovered from parathion degradation were mainly as NO3-, NO2- and NH4+, 80% of the sulphur as SO4(2-), and 5% of phosphorus as PO4(3-). The organic intermediates 4-nitrophenol and methyl paraoxon were also identified, and these were further degraded in solar photocatalytic condition. Two different bioassays (Vibrio fischeri and Daphnia magna) were used to test the acute toxicity of solutions treated by solar photocatalysis and photolysis. The Microtox test using V. fischeri showed that the toxicity expressed as EC50 (%) value increased from 5.5% to >82% in solar photocatalysis, indicating that the treated solution is non-toxic, but only increased from 4.9 to 20.5% after 150 min in solar photolysis. The acute toxicity test using D. magna showed that EC50 (%) increased from 0.05 to 1.08% under solar photocatalysis, but only increased to 0.12% after 150 min with solar photolysis, indicating the solution is still toxic. The pattern of toxicity reduction parallels the decrease in TOC and the parathion concentrations.     

分流液压转向牵引计算的展开图及其应用

本文论及分流液压转向牵引计算的概念,方法及其展开图,并且提供了计算机绘制的展开图和应用实例。     

Hierarchical classifier design in high-dimensional numerous classcases

In applying pattern recognition methods in remote sensing problems, an inherent limitation is that there is almost always only a small number of training samples with which to design the classifier. A hybrid decision tree classifier design procedure that produces efficient and accurate classifiers for this situation is proposed. In doing so, several key questions are addressed, among them the question of the feature extraction techniques to be used and the mathematical relationship between sample size, dimensionality, and risk value. Empirical tests comparing the hybrid design classifier with a conventional single layered one are presented. They suggest that the hybrid design produces higher accuracy with fewer features. The need for fewer features is an important advantage, because it reflects favorably on both the size of the training set needed and the amount of computation time that will be needed in analysis     

Improved Poisson intensity estimation: denoising application using Poisson data

Recently, Timmermann and Nowak developed algorithms for estimating the means of independent Poisson random variables. The algorithms are based on a multiscale model where certain random variables are assumed to obey a beta-mixture density function. Timmermann and Nowak simplify the density estimation problem by assuming the beta parameters are known and only one mixture parameter is unknown. They use the observed data and the method of moments to estimate the unknown mixture parameter. Taking a different approach, we generate training data from the observed data and compute maximum likelihood estimates of all of the beta-mixture parameters. To assess the improved performance obtained by the proposed modification, we consider a denoising application using Poisson data.