Numerical analysis of the warpage problem in TSOP

The reliability and the solderability of thin small outline package (TSOP) are significantly affected by the warpage that is generated after epoxy molding compound (EMC) molding process. This warpage problem mainly results from the mismatch of material properties such as Young's modulus, Poisson's ratio and coefficient of thermal expansion (CTE) and the geometric structure of each component for TSOP. The optimization of both material properties and geometric structures using the numerical analysis is necessary to reduce the warpage of TSOP. However, there are still some limitations for the numerical analysis to obtain proper results consistent with the practical warpage values. In this paper, the numerical analysis is performed under the assumption of elastic behavior for EMC. Furthermore, to solve the limitations, the material properties at the molding temperature and the degree of reaction rate at the end of the molding process of EMC are considered together for the analysis. This numerical analysis gives the higher warpage values than the measured ones, and is applicable to the practical design of the reliable electronic package.     

Effective sludge solubilization treatment by simultaneous use of ultrasonic and electrochemical processes.

Sludge disintegration treatment by using simultaneously ultrasonic irradiation and electrolysis was investigated experimentally. A lab-scale diaphragm cell irradiated with ultrasound at a constant oscillating frequency of 20 kHz was used as a reactor. The batch experiments were carried out under different conditions of electric outputs of the ultrasonic generator, electric current for the electrolysis and different initial SS concentrations. A simultaneous treatment in the cathodic compartment without any chemical doses considerably facilitated the sludge solubilization, compared to the sonication alone. An increase in the electric current up to 400 mA under a constant ultrasonic density decreased the specific energy by 55% within the experimental range. The specific energy consumption was also reduced when the initial SS concentration increased. In addition, before carrying out the simultaneous treatment, a brief electrolysis was effective for further reduction of the specific energy and the acceleration of soluble COD generation.     

Development and experimental evaluation of aerodynamic lens as an aerosol inlet of single particle mass spectrometry

This study described a development and an experimental evaluation of an efficient aerodynamic lens inlet of the single particle mass spectrometry. Several key designing parameters and systematic factors were investigated for the whole lens system through a full numerical simulation. From many tests for various designs of the system, we showed that Mach number was not an independent parameter but interrelated well with flow Reynolds numbers and pressures upstream of the orifices. By manipulating the parameters, we showed for the first time a possibility that there exist a universal correlation between optimal Stokes number and a new factor incorporating the other dimensionless variables and a design parameter. The universality was confirmed by the full simulation results. We demonstrated that the new design of the system was capable of focusing ultrafine aerosols in the size range of 30–700 nm. At two different operating conditions, the formations of sub-millimeter beams of 30–300 nm NaCl aerosols are verified by light scattering imaging as well as microprobe observation of deposited aerosol beams. Finally, the measured sizes of aerosol beams agree reasonably well with those from the simulations as a function of particle size.     

Isothermal crystallization behavior of hybrid biocomposite consisting of regenerated cellulose fiber,clay, and poly(lactic acid)

Quantitative analysis of isothermal crystallization kinetics of PLA/clay nanocomposite and PLA/clay/regenerated cellulose fiber (RCF) hybrid composite has been conducted. The crystallization rate constant (k) according to Avrami equation was higher in PLA/clay nanocomposite than in PLA/clay/RCF hybrid composite at the same crystallization temperature. The equilibrium melting temperature obtained by Hoffman–Weeks equation was almost same in both composites, whereas stability parameter was greater in hybrid composite than in nanocomposite. Activation energy of hybrid composite for crystallization was larger than that of nanocomposite. The value of nucleation parameter (K_g) and surface free energy (s_e) of hybrid composite were larger than nanocomposite, indicating that hybrid composite has a less folding regularity than nanocomposite. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal Stability of the Pigments Hydroxysafflor Yellow A, Safflor Yellow B, and Precarthamin from Safflower (Carthamus tinctorius)

ABSTRACT Three major yellow pigments were isolated from safflower petals ( Carthamus tinctorius ) and characterized as hydroxysafflor yellow A (1), safflor yellow B (2), and precarthamin (3) by ¹H-NMR, ¹H-¹H COSY, ¹³C-NMR, HMQC, and HMBC spectral analysis. Thermal degradation reactions of 3 yellow pigments 1 to 3 at temperatures of 70 to 90 °C were carried out at different pH levels within the range of 3.0 to 10.0 by UV-vis spectral measurements. First-order reaction kinetics was observed for the degradation of safflower yellow pigments (1 to 3) at pH 3.0 and 5.0. Activation energies of thermal degradation of 1-3 at pH 5.0 were calculated as 17.0, 15.4, and 20.1 kcal/mol, respectively. At neutral and alkaline conditions, yellow pigments 1-3 did not follow simple first-order kinetics.     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

Effects of tube rupture modeling and the parameters on the analysis of multiple steam generator tube rupture event progression in APR1400

A multiple steam generator tube rupture (MSGTR) event in APR1400 has been investigated using the best estimate thermal hydraulic system code, MARS1.4. The effects of the parameters such as the number of ruptured tubes, rupture location, affected steam generator on the analysis of the MSGTR event in APR1400 are examined. In particular, tube rupture modeling methods, single tube modeling (STM) and double tube modeling (DTM), are compared. The APR1400 is found to have the capability of allowing more than 30 min to operators for the MSGTR event of five tubes. The effects of rupture location on the MSSV lift time is not significant in the case of STM, but the MSSV lift time for tube-top rupture is found to be 25.3% larger than that for rupture at the hot-leg side tube sheet in the case of DTM. The MSSV lift time for the cases that both steam generators are affected (4C5x, 4C23x) are found to be larger than that of the single steam generator cases (4A5x, 4B5x) due to a bifurcation of the primary leak flow. The discharge coefficient of Cd is found to affect the MSSV lift time only for a smaller value of 0.5. It is found that the most dominant parameter governing the MSSV lift time is the leak flow rate. Whether any modeling method is used, it gives the similar MSSV lift time if the leak flow rate is close, except in the case where both steam generators are affected. Therefore, the system performance and the MSSV lift time of the APR1400 are strongly dependent on the break flow model used in the best estimate system code.     

The Fabrication and Characterization of Single‐Component Polymeric White‐Light‐Emitting Diodes

By using Ni⁰‐mediated polymerization, we have systematically synthesized a series of fluorene‐based copolymers composed of blue‐, green‐, and red‐light‐emitting comonomers with a view to producing polymers with white‐light emission. 2,7‐Dibromo‐9,9‐dihexylfluorene, {4‐(2‐[2,5‐dibromo‐4‐{2‐(4‐diphenylamino‐phenyl)‐vinyl}‐phenyl]‐vinyl)‐phenyl}‐diphenylamine (DTPA), and 2‐{2‐(2‐[4‐{bis(4‐bromo‐phenyl)amino}‐phenyl]‐vinyl)‐6‐tert‐butyl‐pyran‐4‐ylidene}‐malononitrile (TPDCM) were used as the blue‐, green‐, and red‐light‐emitting comonomers, respectively. It was found that the emission spectra of the resulting copolymers could easily be tuned by varying their DTPA and TPDCM content. Thus with the appropriate red/green/blue (RGB) unit ratio, we were able to obtain white‐light emission from these copolymers. A white‐light‐emitting diode using the polyfluorene copolymer containing 3 % green‐emitting DTPA and 2 % red‐emitting TPDCM (PG3R2) with a structure of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonic acid)/PG3R2/Ca/Al was found to exhibit a maximum brightness of 820 cd m^–2 at 11 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.33,0.35), which are close to the standard CIE coordinates for white‐light emission (0.33,0.33).