Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Restraining the associations of anthracene fluorophore by chemically linking to poly(methyl methacrylate)

Associations (dimer or aggregate) of anthracene (An) fluorophores tend to interrupt the monomer emission and reduce the quantum yield (Φ_PL); therefore, poly(methyl methacrylate) (PMMA) chain was used in this study to chemically link to anthracene and to block the mutual associations among the anthracene fluorophores. With this aim, the target polymers were prepared by anionic polymerizations with 9,10‐dibromoanthracene/s‐butyllithium as initiating system to proceed polymerizations of methyl methacrylate (MMA) directly or in the presence of 1,1‐diphenylethylene (DPE). Use of DPE before addition of MMA produces stable initiating anionic species and avoids potential side reactions during polymerization; however, it also introduces four β‐phenylene rings around the central anthracene ring, which interfere with the corresponding emission pattern and reduce the Φ_PL (32%) value due to potential interactions between phenylene rings and anthracene. On the contrast, polymerization without participation of DPE results in polymer with central anthracene ring directly connected to two PMMA chains, which gives clean vibronic emission pattern with limited association emissions and enhanced Φ_PL (52%) value. Physical blending of anthracene by PMMA is less efficient to restrain the associations and results in a film of lower Φ_PL (20%). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and properties of novel amphiphilic sulfated ionomers by the ring‐opening reaction of an epoxidized styrene–butadiene–styrene triblock copolymer

A method for the synthesis of novel sulfated ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed. SBS was first epoxidized by performic acid in the presence of a phase‐transfer catalyst; this was followed by a ring‐opening reaction with an aqueous solution of alkali salt of bisulfate. The optimum conditions for the ring‐opening reaction of the epoxidized SBS with an aqueous solution of KHSO₄ were studied. During the ring‐opening reaction, both phase‐transfer catalyst and ring‐opening catalyst were necessary to enhance the conversion of epoxy groups to ionic groups. The products were characterized with Fourier transform infrared spectrophotometry and transmission electron microscopy (TEM). After the potassium ions of the ionomer were substituted with lead ions, the lead sulfated ionomer exhibited dark spots under TEM. Some properties of the sulfated ionomer were studied. With increasing ionic groups or ionic potential of the cations, the water absorbency and emulsifying volume of the ionomer and the intrinsic viscosity of the ionomer solution increased, whereas the oil absorbency decreased. The sulfated ionomer possessed excellent emulsifying properties compared with the sulfonated SBS ionomer. The sodium sulfated ionomers in the presence of 10% zinc stearate showed better mechanical properties than the original SBS. When the ionomer was blended with crystalline polypropylene, a synergistic effect occurred with respect to the tensile strength. The ionomer behaved as a compatibilizer for blending equal amounts of SBS and oil‐resistant chlorohydrin rubber. In the presence of 3% ionomer, the blend exhibited much better mechanical properties and solvent resistance than the blend without the ionomer. SEM photographs indicated improved compatibility between the two components of the blend in the presence of the ionomer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Survey of nitrate and nitrite contents of vegetables grown in Korea.

A scientific basis for the evaluation of the risk to public health arising from excessive dietary intake of nitrate in Korea is provided. The nitrate () and nitrite () contents of various vegetables (Chinese cabbage, radish, lettuce, spinach, soybean sprouts, onion, pumpkin, green onion, cucumber, potato, carrot, garlic, green pepper, cabbage and Allium tuberosum Roth known as Crown daisy) are reported. Six hundred samples of 15 vegetables cultivated during different seasons were analysed for nitrate and nitrite by ion chromatography and ultraviolet spectrophotometry, respectively. No significant variance in nitrate levels was found for most vegetables cultivated during the summer and winter harvests. The mean nitrates level was higher in A. tuberosum Roth (5150 mg kg(-1)) and spinach (4259 mg kg(-1)), intermediate in radish (1878 mg kg(-1)) and Chinese cabbage (1740 mg kg(-1)), and lower in onion (23 mg kg(-1)), soybean sprouts (56 mg kg(-1)) and green pepper (76 mg kg(-1)) compared with those in other vegetables. The average nitrite contents in various vegetables were about 0.6 mg kg(-1), and the values were not significantly different among most vegetables. It was observed that nitrate contents in vegetables varied depending on the type of vegetables and were similar to those in vegetables grown in other countries. From the results of our studies and other information from foreign sources, it can be concluded that it is not necessary to establish limits of nitrates contents of vegetables cultivated in Korea due to the co-presence of beneficial elements such as ascorbic acid and alpha-tocopherol which are known to inhibit the formation of nitrosamine.     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

带肋钢筋套筒挤压连接的质量控制

针对太原可口可乐综合厂房主筋采用φ28、φ32三级钢存在的可焊性差的问题，提出了在施工中采用套筒挤压连接的方式，并对该方法的操作要点及质量控制措施进行了总结。     

基于资源流分析的企业生态补偿机制研究

循环经济作为一种新型的经济范式,成为理论界和实业界共同关注的焦点问题.在循环经济模式下引入了投入产出的资源流管理模型,该模型反映各个过程中资源流的流向和流量,为建立生态补偿机制提供了详细的基础数据,并利用外部环境的完善,推动生态补偿机制在微观领域的实施,从而达到改善企业环境绩效,减少环境污染的目的.     

Porosity distribution in highly compressible cake: Experimental and theoretical verification of the dense skin

The rate of filtration and the water content of cake are influenced by the existence of a dense skin in a highly compressible cake. The phenomenon of the dense skin has been rarely studied, and its existence has not been verified experimentally. In this study, the porosity variation in a very compressible cake is measured by using a new experimental apparatus, and with this the existence of dense skin has been established experimentally. ‘Unified theory on solid-liquid separation’, a recently developed theory, is utilized for calculating the porosity variation in a very compressible cake.     

北京谱仪Ⅱ（BESⅡ）顶点探测器数据获取系统

北京谱仪（ＢＥＳⅡ）顶点探测器数据获取系统是北京谱仪数据获取系统的一部分，该子系统电子学采用快总线标准，本文描述了该系统的硬件结构和软件系统，软件包括快总线系统的微码软件和上层控制软件，该系统的死时间为１．５ｎｓ，对ＢＥＳⅡ系统总死时间的贡献小于０．５ｍｓ。