Finite element crack growth algorithm for dynamic fracture

A new finite element crack growth algorithm has been developed to simulate dynamic fracture. In this algorithm, pseudo elements with very high initial density are placed below the crack plane and the density is reduced to zero in a gradual manner as the crack passes the element. A number of linear elastic and elasto-viscoplastic problems have been carried out to test the new algorithm. The results are compared with some of the existing crack growth models.     

Ultrastructural studies of spermiogenesis in rabbit exposed to chronic fluoride toxicity

OBJECTIVE: To compare skinfold thickness measurements with bioelectrical impedance analysis (BIA) as a measure of body fat for use in a survey of children (the National Study of Health and Growth). DESIGN: Part cross-sectional, part repeated measurement study. SETTING: A junior school in Bath. SUBJECTS: 42 boys and 33 girls aged from 9 to 11 years. INTERVENTIONS: Measurements of BIA, height, weight, and triceps, biceps, subscapular and suprailiac skinfolds. RESULTS: All measurements were highly repeatable with intraclass correlation coefficients > 0.90. The level of agreement between estimates of percentage of body fat derived from prediction equations based on impedance or skinfold measurements respectively was poor: the mean difference (impedance estimate minus skinfold estimate) was 4.67% (95% range -3.47 to 12.82) for boys and 7.81% (95% range 1.27 to 14.34) for girls. The two estimates were found to correlate highly (r = 0.83 for boys and r = 0.81 for girls) because weight, used to convert estimates of fat-free mass derived from impedance to fat mass, was highly correlated with impedance and moderately highly correlated with skinfold thicknesses. The correlations of resistance (R) and (H)2/R with skinfold thicknesses were very low. There was a moderate correlation of R and H2/R with log(weight-for-height index), but lower than that of log(weight-for-height index) with each of the skinfolds. CONCLUSIONS: As currently available equations for converting impedance-based estimates of total body water to fat mass are not fully developed for use in children of varying ages, estimates of body fat calculated from skinfold thickness measurements remain preferable in epidemiological studies of children's health and growth.     

Development of a heterogeneous microstructurally based finite element model for the prediction of forming limit diagram for sheet material

A heterogeneous finite element model with randomly distributed inhomogeneities has been developed for the determination of the forming limit diagram (FLD) for thin aluminum sheet material based on the prediction of localized necking. The strength difference between the inhomogeneities and the matrix is ascertained either from the fluctuation of the experimental stress-strain curve or from a micromechanical analysis that uses a representative particle field. By changing the specimen geometry and friction conditions, different stress states (or strain paths) are achieved. A plot of the critical Oyane fracture parameter is used to identify the limit strain state. Also, a plot of equivalent plastic strain rate is used to distinguish the boundary of intense shear bands and hence to identify where to take the measurement point. Both a plane stress model and a three-dimensional (3-D) model are adopted to predict the shear banding phenomenon and hence the FLD. The predicted FLD agrees well with the measurements from a recent round robin experimental FLD involving several independent research laboratories. The Taguchi method is applied to assess how the various parameters involved in the heterogeneous model affect the calculated forming limit strain.     

TEM study of microstructure development during low-cycle fatigue of an overaged Al-Mg-Si alloy

The evolution of dislocation structure during room-temperature, uniaxial, low-cycle fatigue of an overaged Al-Mg-Si alloy is studied. Ageing at 450°C produces a fine dispersion of Mg₂Si precipitate particles. During fully reversed strain-controlled cyclic tests, these fine particles restrict deformation to local regions and a stable dislocation substructure is developed early in fatigue life. Substructural observations of hardening and saturation by transmission electron microscopy reveal extensive dislocation band formation on Mg₂Si precipitate rods. Various microstructural features such as configuration of tangled dislocations, dislocation cells, precipitate morphologies, sizes, precipitate-free zones, etc., have been examined during cyclic hardening and saturation. The results have been analysed in terms of kinematic and isotropictype microstructural mechanisms.     

Design Errors: Inefficiency or Carelessness of Designer?

Design defects are experienced in many projects; the difference is only in the extent of occurrence. This technical note discusses a design error case in a building project in Nepal, where the designer made the wrong assumptions in roof treatment work for waterproofing as well as for heat insulation purposes. From the investigation of the problem, it was found that the waterproofing polymer was not applied directly over concrete slab top. Use of heavy concrete block as a heat insulation material also helped to increase the leakage problem. The problem evoked loss of prestige for project officials, the design consortium, and the contractor.     

ShOC rectifier: a new metal-semiconductor device with excellent forward and reverse characteristics

We report a new structure, called the shielded ohmic contact (ShOC) rectifier which utilizes trenches filled with a high-barrier metal to shield an Ohmic contact during the reverse bias. When the device is forward biased, the ohmic contact conducts with a low forward drop. However, when reverse biased, the Ohmic contact is completely shielded by the high-barrier Schottky contact resulting in a low reverse leakage current. Two dimensional numerical simulation is used to evaluate and explain the superior performance of the proposed ShOC rectifier.     

Liquid phase epitaxial growth of pure and doped GaSb layers: morphological evolution and native defects

Undoped and Te-doped gallium antimonide (GaSb) layers have been grown on GaSb bulk substrates by the liquid phase epitaxial technique from Ga-rich and Sb-rich melts. The nucleation morphology of the grown layers has been studied as a function of growth temperature and substrate orientation. MOS structures have been fabricated on the epilayers to evaluate the native defect content in the grown layers from theC-V characteristics. Layers grown from antimony rich melts always exhibitp-type conductivity. In contrast, a type conversion fromp- ton- was observed in layers grown from gallium rich melts below 400 C. The electron mobility of undopedn-type layers grown from Ga-rich melts and tellurium doped layers grown from Sb- and Ga-rich solutions has been evaluated. Paper presented at the poster session of MRSI AGM VI. Kharagpur. 1995     

Estimation of wood char size at the end of devolatilization in a bubbling fluidized bed combustor

Two processes, namely shrinkage and primary fragmentation are known to be the major causes of size reduction of wood during its devolatilization in a fluidized bed combustor. A simple phenomenological model incorporating these effects to compute the average char size at the end of devolatilization is proposed. Experiments are conducted in a bubbling fluidized bed combustor using wood having three different shapes namely, cylinder, cuboid and sphere, to measure the average char size at the end of devolatilization. The model prediction of average char size agrees with the measured values within a deviation of 15%. An experimental correlation is derived to determine the number of fragments and is used to estimate the mean char size.