Temperature Profile of Anatase-TiO2Powder Compact during Microwave Heating

Anatase-TiO₂ cylindrical pellets were microwave sintered and partially transformed to rutile-TiO₂.The rutile concentration profile was determined as a function of location within the pellet. The rutile distribution in the microwavesintered pellets was different from that in pellets sintered by conventional fast firing. Temperature profiles within the pellets were estimated using the irreversible nature of the anatase-rutile transformation. The estimated temperature profile within each pellet was not uniform. In the axial direction, maximum temperature occurred in the middle of the pellet. In the radial direction, maximum temperature occurred at 1 mm below the surface of the cylinder wall. Analysis of the temperature profile indicated that, although heat flow occurred in the microwave-sintered pellet, the temperature profile did not change during a microwave exposure of 5–90 min.     

Permeation and separation of organic liquid mixtures through liquid-crystalline polymer networks

A side-chain liquid-crystalline polymer (LCP) was synthesized by the addition of the mesogenic monomer to poly(methyl siloxane) in presence of a Pt-catalyst. When an aqueous solution of 10wt% ethanol was permeated through a LCP membrane by pervaporation at various temperatures, the permeation rate increased with increasing temperature and drastically changed at glass-nematic (Tg) and nematic-isotropic (TNI) transition temperatures of the LCP membrane. The LCP membrane exhibited the waterpermselectivity in the glassy and liquid-crystalline states. The ethanol concentration in the permeate increased with increasing permeation temperature and the LCP membrane changed from the waterpermselectivity to the ethanol-permselectivity around TNI. These results suggested that the permselectivity was influenced by the change of the LCP membrane structure, that is, its state transformation. It was found that a balance of the orientation of mesogenic groups and flexibility of siloxane chains is very important for the permeability and selectivity.     

Oligosaccharide structures formed during the hydrolysis of lactose by Aspergillus oryzae β-galactosidase

Di-, tri-, tetra-, penta- and hexasaccharides were formed during the hydrolysis of lactose by transgalactosylation reaction of Aspergillus oryzae β-galactosidase. In this study the isolation and characterization of the major constituents of tri-, tetra- and pentasaccharides are described. The structure elucidation of 3 tri-, 2 tetra- and 1 pentasaccharides was carried out by methylation analysis, mass spectrometry and ¹³C-nmr spectrometry. The trisaccharides are $\text{O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 3)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 4)-}\text{d}\text{-}\text{glucose}\text{(3′-}\text{galactosyl-lactose}\text{)}$, $\text{O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 4)-}\text{d}\text{-}\text{glucose}\text{(6′-}\text{galactosyl-lactose}\text{)}$ and $\text{O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 4)-O-[β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)]-}\text{d}\text{-}\text{glucose}\text{(4,6-}\text{digalactosyl-glucose}\text{)}$. Tetrasaccharides are $\text{O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 4)-}\text{d}\text{-}\text{glucose}$ and $\text{O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 3)}$ [or $\text{O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 3)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)]-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 4)-}\text{d}\text{-}\text{glucose}$. Pentasaccharide is $\text{O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 6)-O-β-}\text{d}\text{-}\text{galactopyranosyl}\text{-(1 → 4)-}\text{d}\text{-}\text{glucose}$.     

A far-infrared spectroscopic study of low temperature soft phonon mode in Tris-Sarcosine Calcium Chloride(TSCC)

Temperature dependences of the soft phonon frequency and the damping constant in Tris-Sarcosine Calcium Chloride (TSCC) single crystal have been investigated between 5K and 100K by using a Fourier-transform far-infrared spectrometer. It has been observed that the soft phonon frequency decreases gradually and the damping constant increases as the transition temperature is approached from below The damping constant varies from 7cm^-1 a 90K to less than 0.5cm^-1 at 5K. It has been found that the damping constant is approximately proportional to temperature below about 60K.     

Titania NOx sensors for exhaust monitoring

Oxide semiconductors have been examined to develop NO_x sensors for exhaust monitoring. Titania doped with trivalent elements, such as Al³⁺, Sc³⁺, Ga³⁺ or In³⁺, has a good sensitivity and selectivity to NO between 450 and 550 °C, and shows rapid response. A sensor probe for monitoring exhaust NO_x has been fabricated. Many kinds of interference gases, such as C₃H₆, CO and SO₂, have been found to have only a slight influence on the sensor response to NO. The influence of O₂ and H₂O is also negligible, except for the cases of 0% H₂O and fuel-rich conditions. In accordance with these results, the sensor probe operates satisfactority in the exhaust gas of various combustion conditions without interference from the various kinds of gas species in the exhaust gases.     

Preparation of rod-shaped BaTiO3 powder

Rod-shaped BaTiO₃ powder particles have been prepared from rod-shaped TiO₂ ·nH₂O and BaCO₃ in molten chloride. The morphology of BaTiO₃ particles was studied referring to the effects of the chemical species of the starting titanium compound, amount of chloride, particle size of the titanium compound and reaction conditions, and the preparation condition of rod-shaped BaTiO₃ has been determined: i.e., large TiO₂ ·nH₂O particles were heated at 700°C in molten salt with an equal amount of BaTiO₃. This condition was effective in suppressing the formation of BaTiO₃ by a solution-precipitation process as well as the deformation of either TiO₂ ·nH₂O or BaTiO₃, which are responsible for the formation of equiaxed BaTiO₃ particles. The obtained rod-shaped BaTiO₃ particles had a cubic symmetry. Electron diffraction analysis showed that the following topotactic relation is retained; 0 1 0_{potassium tetratitanate} 0 1 0_{hydrated titania} 1 0 0_anatase 1 0 0_{barium titanate}     

Formation of monodispersed Ta2O5 powders

The Ta₂O₅ powders synthesized by the hydrolysis of tantalum pentaethoxide, Ta(OC₂H₅)₅ in alcoholic solution were monodispersed fine oxide particles, which were a uniform, spherical shape, non-agglomerate, and had a narrow size distribution. They grew to 1.2m after ageing for 1 h after hydrolysis. Powder X-ray diffraction and differential thermal analysisthermogravimetric analysis showed the particles were amorphous and hydrated. These particles lost the water at 290° C and gave well-crystalline Ta₂O at 740° C. Throughout these thermal processes, the particle morphology was kept almost the same.     

Growth of Al2O3 whiskers by vapour-phase reactions

Needle-like or wool-like Al₂O₃ whiskers can be grown on a substrate by the hydrolysis of aluminium fluoride vapour. Effects of the growth conditions on the morphology of the crystals and growth processes of the whisker were investigated, and the optimum growth condition of whiskers was examined. Adequate vapour pressure conditions of the reactant gases for the growth of the wool-like whisker were found to be . Aluminium oxyfluoride was assumed to be the most probable intermediate species for the growth of Al₂O₃ whiskers. A variety of crystal morphologies are also shown and described with respect to the experimental conditions.