Fracture toughness measurement with fatigue-precracked single edge-notched beam specimens of WC-Co hard metal

The plain-strain fracture toughness of WC-8%Co hard metal, K _IC, was measured using single edge-notched beam (SENB) specimens with fatigue precrack. The fatigue precrack was introduced with compressive fatigue cycling in four-point bending at room temperature. Since stable fatigue-crack propagation was obtained from the notch tip, it was easy to control the fatigue-precrack length. A reasonable K _IC value of 13.3 MPa m^1/2 was obtained with the fatigue-precracked SENB specimens in four-point bending. The compressive fatigue-precracking technique in four-point bending was simple and convenient, and is therefore applicable to precracking in a variety of brittle materials prior to fracture-toughness measurements.     

Primary hepatic carcinoid tumor

A case of primary carcinoid tumor arising in the liver of a 69 year old woman with no endocrine symptoms is reported. Histopathologically, the tumor was diagnosed initially as a hepatocellular carcinoma in the biopsy specimen, and was shown subsequently to be a carcinoid tumor, demonstrating diffuse positive staining with Grimelius method. Mucin stained with periodic acid-Schiff (PAS), alcian-blue, and mucicarmine, and was shown partially in the glandular structures. Immunohistochemically, most of the tumor cells stained positively for chromogranin-A, epithelial membrane antigen (EMA) and neuron specific enolase (NSE). Ultrastructural examination revealed electron-dense core granules, measuring 40-120 nm in diameter in some of the tumor cells. Intensive and careful searches pre- and post-operatively revealed no other primary source of tumor other than the liver. The patient was reported well with no symptoms 3 1/2 years after the operation. This case is considered to be a primary hepatic carcinoid tumor. The recent literature is reviewed, and the possible histogenesis of hepatic carcinoid tumor is discussed.     

Characterization of AlGaAs microstructure fabricated by AlGaAs/GaAsmicromachining

An AlGaAs/GaAs micromachining technique that is compatible with laser diode fabrication process is described. AlGaAs structural layers and GaAs sacrificial layers are prepared by metal organic vapor phase epitaxy. Reactive dry etching with chlorine is used to fabricate high-aspect structures. Peroxide/ammonium hydroxide solution is used for selective etching of the sacrificial layer. Since the epitaxial layer has low stress, precise undeformed microstructures are obtained. Good compatibility with the LD process makes it possible to integrate microcantilever beams with LD's without degradation of LD characteristics. Microcantilever beams of AlGaAs are characterized by directly measuring stiffness and natural frequencies. A fracture test is also performed on the AlGaAs microcantilever beams. The average fracture stress of AlGaAs is found to be 1 GPa at 1% strain, which shows that the material is strong enough to support the micrometer scale structures     

IMPINGING JET DRYER

In coating and gravure printing, an impinging jet nozzle with high thermal efficiency for drying of coated film was developed.

Trial production 0f 40 kinds of nozzle enables to develop a high-performance impinging jet nozzle with heat transfer coefficient 1.5 times larger than that of current slit nozzle, through measurement of heat transfer coefficient, visualizations of air flow and heat transfer, and measuremenu of jet velocity and turbulence distribution. The purpose of the trial production was to expand a range of high heat transfer and promote turbulence compared with the current nozzle.

Paying attention to mass transfer within gravure ink coated film, drying characteristic of the film was analyzed by numerical solution of a set of equations governing the drying process in which concentration dependencies 0f the diffusion coefficient and the equilibrium vapor pressure were considered.

Applying these analyses. an industrial scale dryer with excellent drying efficiency has finally been developed.     

Thiamine pyrophosphatase activity in the Golgi apparatus of calcitonin-treated osteoclasts.

The thiamine pyrophosphatase (TPPase) activity described by Novikoff and Goldfisher was examined in osteoclasts affected by calcitonin in order to elucidate whether the morphological and functional changes of the osteoclasts have an influence over the secretion function of their Golgi apparatus. The Golgi apparatus of osteoclasts of which the ruffled border had disappeared and bone resorption discontinued as the result of treatment with calcitonin showed a slight TPPase activity. The reaction products of the enzyme in these inactive osteoclasts were distinctly fewer than that of control osteoclasts, which were not affected by calcitonin. From these results, it is suggested that there may be a connection between the morphological and functional changes of osteoclasts and the secretion function of the Golgi apparatus.     

Effects of weak shear on hyperswollen lyotropic smectic liquid crystals

We have developed a Zimm-type viscometer specially designed for the simultaneous measurements of the structure factor and the viscosity of hyperswollen lyotropic liquid crystals under a very weak shear. We have investigated the shear effects on the layer undulation fluctuation in the lamellar structure and the transition from the anisotropic lamellar to the isotropic sponge phase. We have found a significant difference in the rheological properties between the lamellar and the sponge phase: The former exhibits non-Newtonian flow behavior, while the latter exhibits Newtonian behavior.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

Application of boundary element method to 3-D problems of coupled thermoelasticity

This paper deals with a new boundary element method for analysis of the quasistatic problems in coupled thermoelasticity. Through some mathematical manipulation of the Navier equation in elasticity, the heat conduction equation is transformed into a simpler form, similar to the uncoupled-type equation with the modified thermal conductivity which shows the coupling effects. This procedure enables us to treat the coupled thermoelastic problems as an uncoupled one, A few examples are computed by the proposed BEM, and the results obtained are compared with the analytical ones available in the literature, whereby the accuracy and versatility of the proposed method are demonstrated.     

Multichannel fiber ferrule for a stable laser-diode array module

We developed a multichannel fiber ferrule for a stable laser-diode array module. To apply YAG laser welding to parallel butt couple between the laser-diode and the single-mode fiber arrays, hermetically sealed and precisely aligned equi-interval fibers are required. We describe a V-grooved ceramic ferrule for embedding fibers. Fibers are fixed by soldering, using a flat ceramic lid and aligned with a 250 μm pitch. Our ferrule allowed a metallic, stem mounting laser-diode, to be fixed by YAG laser welding. All 30 samples tested have a leak rate of less than 1×10^-10 atm·cc/s. Optical coupling of fabricated modules was 9.7±0.2 dB and coupling loss change from 25°C to 115°C was within 0.5 dB     

A study of uncertain state estimation

In this paper, we present results of uncertain state estimation of systems that are monitored with limited accuracy. For these systems, the representation of state uncertainty as confidence intervals offers significant advantages over the more traditional approaches with probabilistic representation of noise. While the filtered-white-Gaussian noise model can be defined on grounds of mathematical convenience, its use is necessarily coupled with a hope that an estimator with good properties in idealised noise will still perform well in real noise. In this study we propose a more realistic approach of matching the noise representation to the extent of prior knowledge. Both interval and ellipsoidal representation of noise illustrate the principle of keeping the noise model simple while allowing for iterative refinement of the noise as we proceed. We evaluate one nonlinear and three linear state estimation technique both in terms of computational efficiency and the cardinality of the state uncertainty sets. The techniques are illustrated on a synthetic and a real-life system.     

Computer aided kinetic modeling with KMT and KME

The complexity of many chemical and refining reaction systems and the thus-derived tedious and time-consuming process of building the associated kinetic models have been major obstacles in the use of fundamental kinetics in the solution of chemical engineering problems. This review summarizes work aimed at removing theses obstacles. Our recent work that has led to the enhancement of the Kinetic Modeler's Toolbox (KMT) and the development of the Kinetic Model Editor (KME) presents an end-to-end solution to the kinetic modeling process, including automated feedstock modeling, reaction network construction, kinetic rate estimation, model programming, process system configurations, model customizations, compilations, model execution and results analysis.