Proposal of a simplified method for integrating reduction of effective power of pumped storage into a generation system planning method

Pumped storage hydropower stations are extensively used as peaking and reserve power plants. The current trend in this area is to increase their power output relative to the capacity of reservoirs, which results in a shorter maximum duration of full‐power operation while availability of the energy required for the pumping becomes less evident. This increases the possibility of reducing the effective power of pumped storage units in the case of a tight supply–demand balance in the power system. Although many studies have examined a role of pumped storage in generation systems, few studies have explicitly dealt with the power reduction. This paper proposes a new linear programming model that incorporates the reduction of effective power of pumped storage. The proposed model makes it possible to easily incorporate the power reduction in computations by employing hypothetical daily load curves and dispatching loads to the curves. The model also includes LNG combined cycle power generation plants that are now being intensively implemented. The developed model is applied to a power system model. The sample study reveals that the reduction of effective power considerably varies from season to season and the reduction highly affects the optimal generation mix, that is, the optimal share of pumped storage. © 2001 Scripta Technica, Electr Eng Jpn 134(4): 50–61, 2001     

Prospective method of lightning protection schemes in distribution system

Grounding wires and enclosed ZnO elements have been incorporated generally in 6.6‐kV distribution systems by TEPCO for the reduction of lightning overvoltages. At present, the reliability to lightning surges is tolerably good. However, the facility of grounding wires is not inexpensive and its maintenance is hard due to corrosion and disconnection in some areas. A typical model simulating TEPCO field adopting enclosed ZnO elements has been developed and we have evaluated relative failure risks systematically according to conditions with and without grounding wires against lightning overvoltages. Two kinds of failures discussed in the paper are the flashover of insulation and the overduty of ZnO elements, and two kinds of induced and direct lightning overvoltages are studied in flashover. The greatest problem with no grounding wire is the increase of ZnO elements' duty, but it was demonstrated that a short partial grounding wire around ZnO elements or the selection of heavier ZnO elements provides a solution. The main objectives of this study are to clarify the relative failure risks systematically according to realistic field conditions, the risk of small stroke currents having long duration to ZnO elements' duty, and countermeasures against ZnO elements' overduty. © 1999 Scripta Technica, Electr Eng Jpn, 127(1): 1–10, 1999     

Practical Continuous‐Flow Controlled/Living Anionic Polymerization

A continuous‐flow reaction system was developed, allowing flow conditions of the entire system to be maintained at a predetermined constant level, which is one of the most significant factors for successful industrial application. Controlled/living anionic polymerization was selected as a model reaction since the characteristics of its polymer products, molecular weights, and molecular weight distributions are highly susceptible to changes in the relative flow rates of a monomer and initiator solutions. In flow microreactors, controlled/living anionic polymerization of styrene in tetrahydrofuran (THF)/hexane initiated by THF‐diluted n‐butyllithium (n‐BuLi) was examined. Poly(styrenes) of larger molecule sizes such as Mn > 15 000 were successfully synthesized. After continuous operation for four hours, ca. 0.5 kg of the polymer was readily produced with narrow molecular weight distribution, demonstrating the applicability of this continuous‐flow system for controlled/living anionic polymerization on considerably large scale with a view to its industrial usage in the future.     

Calcium silicate structure and carbonation shrinkage of a tobermorite-based material

Carbonated autoclaved aerated concretes (AACs) show no shrinkage at a degree of carbonation approximately less than 20%. The ²⁹Si MAS NMR spectrum showed that at a degree of carbonation less than 25%, the typical double-chain silicate anion structure of tobermorite-11Å was well maintained and interlayer Ca ions were exchanged with protons. This corresponded to the absence of carbonation shrinkage at a degree of carbonation less than 20%. When the degree of carbonation increased from 25% to 50% up to 60%, the double-chain silicate anion structure of tobermorite-11Å was decomposed and Ca ions in the Ca-O layers were dissolved, showing a possible mechanism of carbonation shrinkage.     

Epitaxial growth of titanium oxide thin films on MgO(100) single-crystal substrates by reactive deposition methods

We synthesized titanium oxide thin films on MgO(100) single-crystal substrates by two reactive deposition methods and compared the structures of the thin films formed by these methods. In one method (pulsed-molecular-beam deposition method), molecular oxygen is supplied to the substrates by using a pulsed-molecular-oxygen beam source and deposition of one unit layer of titanium and subsequent supply of molecular oxygen are repeatedly performed. In the other method (radical beam deposition method), atomic oxygen is irradiated to the substrates by using an atomic oxygen beam generated by the radical beam source and irradiation of the atomic oxygen and deposition of titanium are simultaneously performed. In the case of the pulsed-molecular-beam deposition method, the crystal structure was changed by increasing the number of oxygen pulses supplied from the beam source. We found that the crystal structure of titanium oxide depended on the composition ratio of O:Ti in the film. The maximum ratio of O:Ti attainable by this method was 1.85, and at this ratio, (100)-oriented pseudorutile was formed. In the case of the radical beam deposition method, (100)-oriented anatase was formed below the titanium deposition rate of 0.10 nm/s and pseudorutile (TiO_2−δ) was formed above 0.15 nm/s. The pseudorutile structure synthesized on this experiment was very stable in air. We concluded that the crystal structure of the pseudorutile is a new crystal structure of titanium oxide.     

Nanosecond and femtosecond mass spectroscopic analysis of a molecular beam produced by the spray-jet technique

The spray-jet molecular beam apparatus enabled us to produce a molecular beam of non-volatile molecules under high vacuum from a sprayed mist of sample solutions. The apparatus has been used in spectroscopic studies and as a means of molecular beam deposition. We analyzed the molecular beam, consisting of non-volatile, solvent, and carrier-gas molecules, by using femtosecond- and nanosecond- laser mass spectroscopy. The information thus obtained provided insight into the molecular beam produced by the spray-jet technique.     

Epitaxial growth of WOx nanorod array on W(001)

Nanorods of substoichiometric tungsten oxide (WO_x) were grown on W(001) substrates. Two methods for the growth of nanorods were used: oxidation of the substrate under appropriate conditions and the deposition of tungsten oxide from a tungsten foil heated in the presence of oxygen. The grown nanorods were observed using a scanning electron microscope and an atomic force microscope. The diameters of the nanorods were 5–20 nm. The nanorods were slightly inclined from the directions parallel or normal to the surface. The inclination of nanorods was explained in terms of the epitaxial relationship between WO₃ crystals and the W(001) substrate. The WO₃ crystals formed at the initial stage of growth act as the nuclei of WO_x nanorods. We observed selective enhancement of the growth in a certain epitaxial direction depending on the method of growth, and an array of WO_x nanorods was produced on the W(001) substrate.     

Large Magnetovolume Effect Induced by Embedding Ferromagnetic Clusters into Antiferromagnetic Matrix of Cobaltite Perovskite

Materials that show negative thermal expansion (NTE) have significant industrial merit because they can be used to fabricate composites whose dimensions remain invariant upon heating. In some materials, NTE is concomitant with the spontaneous magnetization due to the magnetovolume effect (MVE). Here the authors report a new class of MVE material; namely, a layered perovskite PrBaCo₂O_5.5+x (0 ≤ x ≤ 0.41), in which strong NTE [β ≈ ?3.6 × 10^?5 K^?1 (90–110 K) at x = 0.24] is triggered by embedding ferromagnetic (F) clusters into the antiferromagnetic (AF) matrix. The strongest MVE is found near the boundary between F and AF phases in the phase diagram, indicating the essential role of competition between the F‐clusters and the AF‐matrix. Furthermore, the MVE is not limited to the PrBaCo₂O_5.5+x but is also observed in the NdBaCo₂O_5.5+x . The present study provides a new approach to obtaining MVE and offers a path to the design of NTE materials.     

High-intensity multi-bunch beam generation by a photo-cathode RF gun

A multi-bunch photo-cathode RF gun system has been developed as an electron source for the production of intense quasi-monochromatic X-rays based on inverse Compton scattering. The desired multi-bunch beam is 100 bunches/pulse with a total charge of 500 nC and a bunch spacing of 2.8 ns. We modified the gun cavity of a ‘BNL-type IV’ RF gun to allow a CsTe cathode plug in the end plate. The system uses a four-dipole chicane beam line to allow the injection of laser light normal to the cathode surface. We compensate the gun cavity beam loading caused by the high-intensity multi-bunch electron beam by injecting the laser pulse before RF power has filled the cavity. We have achieved a total intensity of 220 nC in 100 bunches with a bunch-to-bunch energy spread under 1.3% (peak-to-peak). This paper concentrates on experiments to generate the high-intensity multi-bunch beam with compensation of the bunch-to-bunch energy spread due to heavy beam loading.