Direct dissimilar joining of aluminium alloys and polyamide 6 by friction lap joining*

Direct dissimilar joining of various Al alloy (A1050, A3004, A5052 and A5083) plates and a polyamide 6 plate was performed using friction lap joining (FLJ) with the Al alloy plate as a top and the polyamide 6 plate as a bottom. The effect of Mg content in Al alloys on the joining strength was investigated. TEM analysis made clear that the polyamide 6 and Al alloys were joined via oxide layer consisting of Al₂O₃ and MgO. The results of XPS analysis indicated that MgO was formed by the heating during FLJ, and the quantity of MgO was increased with increasing Mg content in Al alloys. The tensile shear strengths of A3004, A5052 and A5083 joints were saturated to about 2 kN because of the tensile fracture at the polyamide 6 plate outside the tool-passed zone, which were higher than that of the A1050 joint fractured at the joint interface. The peel strength of the joint was increased with increasing Mg content in Al alloys, and the fracture occurred both at the joint interface and at the polyamide 6 plate on the joint area. The fraction of polyamide 6 plate fracture was also increased with increasing Mg content in Al alloys.     

Beta tricalcium phosphate ceramics with controlled crystal orientation fabricated by application of external magnetic field during the slip casting process

Beta tricalcium phosphate (β-TCP) is a resorbable bioceramic that has hitherto been utilized in the medical field. Since it crystallizes in the anisotropic hexagonal system, properties such as chemical and physical ones are expected to depend on its crystal axis direction and/or on its crystal plane (anisotropy). Control of crystal orientation is thus important when used in polycrystalline form. Meanwhile, application of a strong magnetic field has been found to be a promising technique to control crystal orientation of anisotropic shape or structured crystals. In this work, we attempted to fabricate β-TCP ceramics with controlled crystal orientation by applying an external magnetic field during the slip casting process and subsequently sintering them at 1050 °C, below the β–α transition temperature. Application of a vertical magnetic field increased intensities of planes perpendicular to c-plane on the top surface, while a horizontal one with simultaneous mechanical mold rotation decreased it. These results indicated that crystal orientation of β-TCP ceramics were successfully controlled by the external magnetic field and together that the magnetic susceptibility of β-TCP is χ_c⊥ > χ_c//.     

Skin Permeation of Lidocaine from Crystal Suspended Oily Formulations

ABSTRACT

In vitro permeation of lidocaine (lidocaine base, LID) through excised rat skin was investigated using several LID-suspended oily formulations. The first skin permeation of LID from an LID-suspended oily solution such as liquid paraffin (LP), isopropyl myristate (IPM), polyoxyethylene (2) oleylether (BO-2), and diethyl sebacate (DES) was evaluated and compared with that from polyethylene glycol 400 (PEG400) solution, a hydrophilic base. The obtained permeation rate of LID, J_app, from PEG400, LP, IPM, BO-2, and DES was in the order of DES>BO-2 = IPM>LP>PEG400, and increased with LID solubility in the oily solvents, although LID crystals were dispersed in all solvents. Subsequently, oily formulations that consisted of different ratios of the first oily solvent (IPM, BO-2, or DES) (each 0–20%), the second oily solvent (LP) and an oily mixture of microcrystalline wax/white petrolatum/paraffin (1/5/4) were evaluated. BO-2 groups at a concentration of 5% and 10% had the highest J_app among the oily formulations, although a higher BO-2 resulted in lower skin permeation. In addition, pretreatment with BO-2 increased the skin permeation of LID. These results suggest that the penetration enhancing effect by the system may be related to the skin penetration of BO-2 itself. Finally, mathematical analysis was done to evaluate the effect of BO-2, and it was shown that BO-2 improved the LID solubility in stratum corneum lipids to efficiently enhance the LID permeation through skin.     

Controlled chain polymerisation and chemical soldering for single-molecule electronics

Single functional molecules offer great potential for the development of novel nanoelectronic devices with capabilities beyond today's silicon-based devices. To realise single-molecule electronics, the development of a viable method for connecting functional molecules to each other using single conductive polymer chains is required. The method of initiating chain polymerisation using the tip of a scanning tunnelling microscope (STM) is very useful for fabricating single conductive polymer chains at designated positions and thereby wiring single molecules. In this feature article, developments in the controlled chain polymerisation of diacetylene compounds and the properties of polydiacetylene chains are summarised. Recent studies of "chemical soldering", a technique enabling the covalent connection of single polydiacetylene chains to single functional molecules, are also introduced. This represents a key step in advancing the development of single-molecule electronics.     

l‐Citrulline Supplementation‐Increased Skeletal Muscle PGC‐1α Expression Is Associated with Exercise Performance and Increased Skeletal Muscle Weight

Scope

l ‐citrulline has recently been reported as a more effective supplement for promoting intracellular nitric oxide (NO) production compared to l ‐arginine. Here, the effect of l ‐citrulline on skeletal muscle and its influence on exercise performance were investigated. The underlying mechanism of its effect, specifically on the expression of skeletal muscle peroxisome proliferator‐activated receptor‐gamma coactivator‐1α (PGC‐1α), was also elucidated.

Methods and results

Six‐week‐old ICR mice were orally supplemented with l ‐citrulline (250 mg kg^?1) daily, and their performance in weight‐loaded swimming exercise every other day for 15 days, was evaluated. In addition, mice muscles were weighed and evaluated for the expression of PGC‐1α and PGC‐1α‐regulated genes. Mice orally supplemented with l ‐citrulline had significantly higher gastrocnemius and biceps femoris muscle mass. Although not statistically significant, l ‐citrulline prolonged the swimming time to exhaustion. PGC‐1α upregulation was associated with vascular endothelial growth factor α (VEGFα) and insulin‐like growth factor 1 (IGF‐1) upregulation. VEGFα and IGF‐1 are important for angiogenesis and muscle growth, respectively, and are regulated by PGC‐1α. Treatment with NG‐nitro‐l ‐arginine methyl ester hydrochloride (l ‐NAME), a nitric oxide synthesis inhibitor, suppressed the l ‐citrulline‐induced PGC‐1α upregulation in vitro.

Conclusion

Supplementation with l ‐citrulline upregulates skeletal muscle PGC‐1α levels resulting in higher skeletal muscle weight that improves time to exhaustion during exercise.

     

Design of a photocatalyst for bromate decomposition: surface modification of TiO2 by pseudo-boehmite

The rate of BrO3- reduction by a commercial TiO2 photocatalyst under UV illumination in an aqueous solution was increased by lowering the pH from 7 to 5. The effect is attributable to an enhancement of the electrical interaction between BrO3- and the positively charged surfaces of the TiO2 photocatalyst. The surface charge can be controlled by a surface modification of the TiO2 photocatalyst without controlling the pH of the water. In fact, the isoelectric point of surface-modified TiO2 was higher than that of the unloaded TiO2 photocatalyst, resulting in an increase in the rate of the photocatalytic reduction of BrO3- at a neutral pH. This increase is explained by an increase in the amount of adsorbed BrO3- on the photocatalyst surface.     

Ash deposition behavior of upgraded brown coal in pulverized coal combustion boiler

Ash with a low melting point causes slagging and fouling problems in pulverized coal combustion boilers. Ash deposition on heat exchanger tubes reduces the overall heat transfer coefficient due to its low thermal conductivity. The purpose of this study is to evaluate the ash deposition for Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. The UBC stands for Upgraded Brown Coal. The melting temperature of UBC ash is relatively lower than that of bituminous coal ashes. Combustion tests were conducted on blended coal consisting 20 wt.% of UBC and 80 wt.% of bituminous coal. Before actual ash deposition tests, the molten slag fractions in those coal ashes were estimated by means of chemical equilibrium calculations. The calculation results showed the molten slag fraction for UBC ash reached approximately 90% at 1523 K. However, that for blended coal ash decreased to 50%. These calculation results mean that blending UBC with bituminous coal played a role in decreasing the molten slag fraction. This phenomenon occurred because the coal blending led to the formation of alumino-silicates compounds as a solid phase. Next, ash deposition tests were conducted using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at both 1523 K and 1273 K in the boiler to measure the amount of ash deposits. The results showed that the mass of ash deposition for blended coal did not greatly increase, compared with that for bituminous coal alone. Therefore, appropriately blending UBC with bituminous coal enabled the use of UBC without any ash deposition problems in practical boilers.     

Influence of electrode material on pressure‐rise due to arc in a closed chamber

This paper describes the phenomenon of internal pressure‐rise due to arcs ignited between metal rod electrodes in air. First, the internal pressure‐rises in a closed chamber due to arcs were measured at currents within the range of 1 to 12.5 kA. The rod electrodes were made of copper, iron, and aluminum, and were 20 mm in diameter. The measurements showed that the maximum pressure‐rise distinctly differed with each electrode material at the same total arc energy, namely, the maximum pressure‐rise was the highest in the case of the aluminum electrode and was the lowest in the case of the iron electrode. Next, to quantitatively verify this difference, the internal pressure‐rise was estimated, taking into account the energy balance in the closed chamber on each electrode material. It was found that the estimated pressure‐rise approximately agreed with the above experimental results by taking into consideration oxidation reactions of the electrodes, melting and vaporization of the electrodes, and radiation loss of the arcs under certain realistic assumptions. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 174(4): 9–18, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21071     

C57BL/KsJ-db/db-Apc Mice Exhibit an Increased Incidence of Intestinal Neoplasms

The numbers of obese people and diabetic patients are ever increasing. Obesity and diabetes are high-risk conditions for chronic diseases, including certain types of cancer, such as colorectal cancer (CRC). The aim of this study was to develop a novel animal model in order to clarify the pathobiology of CRC development in obese and diabetic patients. We developed an animal model of obesity and colorectal cancer by breeding the C57BL/KsJ-db/db (db/db) mouse, an animal model of obesity and type II diabetes, and the C57BL/6J-Apc(Min/+) (Min/+) mouse, a model of familial adenomatous polyposis. At 15 weeks of age, the N9 backcross generation of C57BL/KsJ-db/db-Apc(Min/+) (db/db-Min/+) mice developed an increased incidence and multiplicity of adenomas in the intestinal tract when compared to the db/m-Min/+ and m/m-Min/+ mice. Blood biochemical profile showed significant increases in insulin (8.3-fold to 11.7-fold), cholesterol (1.2-fold to 1.7-fold), and triglyceride (1.2-fold to 1.3-fold) in the db/db-Min/+ mice, when compared to those of the db/m-Min/+ and m/m-Min/+ mice. Increases (1.4-fold to 2.6-fold) in RNA levels of insulin-like growth factor (IGF)-1, IRF-1R, and IGF-2 were also observed in the db/db- Min/+ mice. These results suggested that the IGFs, as well as hyperlipidemia and hyperinsulinemia, promoted adenoma formation in the db/db-Min/+ mice. Our results thus suggested that the db/db-Min/+ mice should be invaluable for studies on the pathogenesis of CRC in obese and diabetes patients and the therapy and prevention of CRC in these patients.     

Synthesis of NASICON with New Compositions for Electrochemical Carbon Dioxide Sensors*

Powders and pellets of new NASICON compositions have been synthesized using a mixed inorganic-organic sol-gel synthesis, by the preliminary formation of a pre-hydrolized TEOS xerogel. The investigated compositions can be described by the general formula Na₃Zr_2-(x/4)Si_2-xP_1+xO₁₂, obtained by keeping the Na concentration constant (= 3) at the optimum value reported for ionic conductivity, with x = 0 (the usual NASICON composition), 0.667, and 1.333. The xerogels were calcined at various temperatures in the range 400–1200°C. The powder samples were analyzed by TG/DTA, BET measurements, XRD, and SEM. The powders calcined at 500°C were sintered into pellets at 1100°C for 6 h. The sintering behavior of the pellets was investigated by dilatometric measurements and SEM observations. The sinterability increased with increasing x value. Dense samples of the new compositions were obtained by sintering at only 1100°C. This is attributed to the occurrence of liquid phase sintering. The electrical conductivity of the NASICON sintered bodies was measured by ac impedance spectroscopy. The conductivity decreased with decreasing c₀ lattice parameter of the hexagonal structure or increasing x value. The CO₂ gas sensors, using as electrolyte the dense samples of the new NASICON compositions, showed good EMF response that was very close to the theoretical value, even for the sample with x = 1.333 that showed much lower conductivity.