Purification of Ellagic Acid by UF Membranes

Ellagic acid (2, 3, 7, 8‐tetrahydroxy(1)benzopyrano(5, 4, 3‐cde)(1)benzopyran‐5, 10‐dione) was selected as a model pollutant which is present in the tannic fraction of cork processing wastewater. The ultrafiltration of aqueous ellagic acid solutions through three membranes was studied in tangential UF laboratory equipment. Two of the membranes were polyethersulfone (Biomax10K and Biomax5K, with MWCO of 10000 and 5000 Da, respectively), and the third made of regenerated cellulose (Ultracel5K, with MWCO of 5000 Da). The water hydraulic permeability was evaluated for each membrane. The evolution of the permeate flow rate with processing time was followed, and the influence of the main operating variables (feed flow rate, trans‐membrane pressure and nature of the membranes) on the permeate flux was also established. According to the hypothesis of the film theory, the intrinsic and apparent rejection coefficients, as well as the mass transfer coefficients, were also determined, and the values obtained were discussed as a function of the operating conditions used.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

A case study of regional catchment water quality modelling to identify pollution control requirements.

There are four ecologically important river catchments that contain candidate Special Areas of Conservation (cSACs) under the Habitats Directive in the Lake District National Park located in the North of England. These are the rivers Ehen, Kent, Derwent and Eden. For each cSAC, there are defined ecological criteria that include water quality targets to protect the designated species. Stretches of the riverine cSACs in each catchment are failing to meet these and other water quality targets. The Environment Agency commissioned a study of each catchment to provide the underpinning scientific knowledge to allow it to deliver its statutory obligations under the Habitats Directive. SIMCAT river water quality models were produced and used to predict the water quality impacts resulting from a number of water quality planning scenarios aimed at achieving full compliance with the Habitats Directive and other national and EEC water quality targets. The results indicated that further controls on effluent discharges will allow the majority of targets to be met but other sources of pollution will also need to be controlled. The outcome of the study also recognised that water quality improvements alone will not necessarily produce the required improvement to the ecological interest features in each cSAC.     

Structure and catalytic properties of dealuminated modified zeolites Y

The effect of treatment with a zirconyl nitrate aqueous solution on the structure; the hydroxyl-layer constitution; and the adsorptive, acid, and catalytic properties of dealuminated zeolite Y was studied. The zeolite was prepared by boiling NH₄Y in an ethylenediaminetetraacetic acid disodium salt solution followed by ion exchange with ammonium chloride and calcination in a 100% steam flow at 750°C. X-ray diffraction, IR spectroscopy, and DTA data show the formation of an ultrastable form of zeolite Y. The incorporation of zirconium in zeolite led to an increase in the proportion of strong acid sites, thus raising the yield of cracking products during n-hexane conversion tested on platinum-containing catalyst samples.     

Structure and Certain Properties of Hot-Pressed Boron Carbide-Based Ceramic with Calcium-Silicon Additive

The influence which the composition of powder mixtures, the treatment conditions which the mixtures are subjected to, and the conditions under which the hot-pressed composite materials B₄C – (5-10 mass%) calcium-silicon are fabricated exert on the structure, nature of failure, and mechanical properties of these materials is investigated. Optimum properties are possessed by material containing 10 mass% of addition. It is shown that the structure, morphology, and dispersivity, as well as the nature of the distribution of the components that are added to the composite material (secondary phase) vary as the temperature of hot pressing changes. Maximal mechanical characteristics of the composite material (σ_bend = 560 MPa, K _1c = 4.7 MPa·m^1/2, HV = 37 GPa) are attained at hot-pressing temperatures in the range 2000-2100°C.     

Thermal storage efficiencies of two solar saltless water ponds

A comparative study between two types of solar ponds is presented. The first type has its free surface covered by a thin layer of transparent paraffin oil. The second type is covered by transparent glass floating devices. Each device disposes an air-vacuum chamber. The free water surface between these devices is covered by transparent paraffin oil also. The thermal storage efficiency of each pond is estimated during two time periods: between sunrise and sunset and from midnight to midnight. The calculated efficiency between sunrise and sunset corresponds to the average transmittance–absorptance product. This is estimated using linear regression and also a maximum likelihood identification technique. The behavior of the system was studied by solving numerically the heat transfer equations of the system. Also an ARMAX (AutoRegressivie Moving Average with eXogenous signal) model allowing the assessment of its performance was presented. This efficiency is larger for the first pond during the sunrise to sunset period and smaller when calculated from midnight to midnight. Thus, the first type of pond could be preferred for a use just after the sunset of the same day, while the second for use after one or more days of heat storage.