Experimental research and prediction of the effect of chemical and biogenic sulfuric acid on different types of commercially produced concrete sewer pipes

New equipment and procedures for chemical and microbiological tests, simulating biogenic sulfuric acid corrosion in sewerage systems, are presented. Subsequent steps of immersion and drying, combined with mechanical abrasion, were applied to simulate events occurring in sewer systems. Both chemical and microbiological tests showed that the aggregate type had the largest effect on degradation. Concrete with limestone aggregates showed a smaller degradation depth than did the concrete with inert aggregates. The limestone aggregates locally created a buffering environment, protecting the cement paste. This was confirmed by microscopic analysis of the eroded surfaces. The production method of concrete pipes influenced durability through its effect on W/C ratio and water absorption values. In the microbiological tests, HSR Portland cement concrete performed slightly better than did the slag cement concrete. A possible explanation can be a more rapid colonisation by microorganisms of the surface of slag cement samples. A new method for degradation prediction was suggested based on the parameters alkalinity and water absorption (as a measure for concrete porosity).     

The use of direct osmosis tests as complementary experiments to determine the water and salt permeabilities of reinforced cellulose acetate membranes

In this article the use of the direct osmosis test as a complementary experiment to the reverse osmosis test is described. The membranes investigated are cellulose acetate membranes reinforced with mineral fillers. In both tests the same influence of the type of fillers on the water permeability coefficients is found. The salt permeability coefficients indicate the presence of pressure sensitive defects in the reinforced membranes. The direct osmosis test is found to be a suitable test to confirm and predict the membrane properties under reverse osmosis conditions.     

Optimization of design and operating policy of an industrial two-bed co-shift reactor

The optimal operating policy for a two-bed adiabatic CO-converter is computed using the Discrete Maximum Principle. The problem is then extended to determine also the optimal design of the system. A sensitivity analysis of the optimal solutions is presented, showing the influence of the principal process parameters. Economical, chemical and physical data have been obtained from an existing CO-converter in a standard 1000 short Tons/day NH₃ plant.     

Modelling formation and growth of H2SO4-H2O aerosols: Uncertainty analysis and experimental evaluation

An aerosol dynamics model, AERO2, is presented, which describes the formation of H₂SO₄-H₂O aerosol in a smog chamber. The model is used to analyse how the uncertainties on four input parameters are propagated through an aerosol dynamics model. The input parameters are: the rate of the reaction between SO₂ and OH (k₁), the ratio between the nucleation rate used in AERO2 and that derived from classical nucleation theory (t_n), the H₂SO₄ mass accommodation coefficient () and a measure of the turbulence intensity in the reactor (k_e). Uncertainties for these parameters are taken from the literature. One of the results of the analysis is that AERO2 and aerosol dynamics models in general can only predict upper bounds for the total number (N_tot) and total volume (V_tot) concentrations of the particles. The uncertainties on N_tot and V_tot are mainly due to the uncertainties on k₁, and t_n. An uncertainty factor of 20–100 still remains when the uncertainty on k₁, is reduced to ±5%. Aerosol measurements from three smog chamber experiments have therefore been used, in an attempt to reduce the uncertainty on k₁ and t_n. Values for k₁ are obtained in the reduced range 7.8 × 10⁻¹³ to 1.0 × 10⁻¹² cm³ s⁻¹, which is within the range found in the literature. For t_n, values in the range 10⁴–10⁷ are obtained, which is close to the upper bound of the range in literature. These values for t_n are in marked contrast with a recent set of experiments on nucleation in H₂SO₄-H₂O mixtures, which suggests a value for t_n of at most 10⁻⁵.     

Inhomogeneous Density in Die Compaction: Experiments and Finite-Element Calculations

X-ray density measurements and two-color powder displacement observations were used to determine the reliability of the cylindrical test cell as a source of data for a plasticity model of granular materials. Calculations with such a model agree well with the experimental density distribution, for the cylindrical test cell itself and for a cylindrical die, compacted from one side by means of a profiled plunger .     

The lipids of krill (Euphausia species) and red crab (Pleuroncodes planipes)

The composition of the lipids of two samples of krill and one of “red crab” was determined by thin layer, column and gas chromatographic procedures. A large number of unusual fatty acids were present.     

Satellite-Based Water Quality Mapping from Sequential Simulation with Parameter Outlier Removal

The satellite-based regression model provides the data model that identifies water quality for inland and coastal waters. However, the satellite regression usually depends on the selection of observation, satellite data, and model type. A resampling simulation technique, such as sequential simulation using geographically weighted regression (GWR simulation), can be applied in generating multiple realizations for water quality estimation to reduce the sampling effect and consider spatial heterogeneity. Traditional models often result in considerable underestimation in extreme observations. The GWR simulation provides the best goodness of fit and spatial varying relationship between observed water quality and remote sensing considering parameter outlier and noise removal for parameter stability. This simulation model can increase the sampling diversity from various observations and reduce the neighboring effects of observations using outlier and noise removal. The model that handles spatial uncertainty and heterogeneity is a novel tool for inferring the characteristics of water quality from a series of sample subsets.

     

Figure-ground separation by cue integration

This letter presents an improved cue integration approach to reliably separate coherent moving objects from their background scene in video sequences. The proposed method uses a probabilistic framework to unify bottom-up and top-down cues in a parallel, "democratic" fashion. The algorithm makes use of a modified Bayes rule where each pixel's posterior probabilities of figure or ground layer assignment are derived from likelihood models of three bottom-up cues and a prior model provided by a top-down cue. Each cue is treated as independent evidence for figure-ground separation. They compete with and complement each other dynamically by adjusting relative weights from frame to frame according to cue quality measured against the overall integration. At the same time, the likelihood or prior models of individual cues adapt toward the integrated result. These mechanisms enable the system to organize under the influence of visual scene structure without manual intervention. A novel contribution here is the incorporation of a top-down cue. It improves the system's robustness and accuracy and helps handle difficult and ambiguous situations, such as abrupt lighting changes or occlusion among multiple objects. Results on various video sequences are demonstrated and discussed. (Video demos are available at http://organic.usc.edu:8376/ approximately tangx/neco/index.html .).     

Effectiveness of participatory ergonomic interventions on health outcomes: a systematic review

The objective of this study was to conduct a systematic review of the literature on the effectiveness of participatory ergonomic (PE) interventions for improving workers' health. The search strategy targeted six electronic databases and identified 442 potential articles. Each article was examined by pairs of reviewers for relevance (assessed a participative ergonomic workplace intervention, with at least one health outcome, published in English in peer reviewed literature). Twenty-three articles met relevance criteria and were then appraised for methodological strength. Using a best evidence synthesis approach, 12 studies that were rated as 'medium' or higher provided partial to moderate evidence that PE interventions have a positive impact on: musculoskeletal symptoms, reducing injuries and workers' compensation claims, and a reduction in lost days from work or sickness absence. However, the magnitude of the effect requires more precise definition.     

Thermal efficiency of manifold-heat-pipe heat exchangers

The thermal efficiency of manifold-heat-pipe heat exchangers is considered. A method for predicting the efficiency and an analysis of effects of various factors of the actual process are presented.Academic Scientific Complex A. V. Luikov Heat and Mass Transfer Institute of the Academy of Sciences of Belarus, Minsk. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 66, No. 2, pp. 173–178, February, 1994.