S-P混杂纤维对混凝土长期性能与耐久性影响

采用对比的试验方法,研究并讨论了钢纤维、聚丙烯纤维及其混杂对混凝土长期性能及耐久性的影响.研究结果表明,用不同尺度、不同性质的钢纤维与聚丙烯纤维按二元混杂以总体积率0.9%掺入高性能混凝土中,明显改善了水泥混凝土的长期性能,90d干缩值减少36.6%,200d徐变度降低45.4%,并可显著提高混凝土的耐久性能,相对渗透系数降低79.03%,氯离子渗透系数降低30.5%.     

普通电火花成型机床加工小孔的改进方法

针对普通电火花成型机床在进行较深的小孔加工时存在的问题,对电火花成型机床进行部分改造,增加一个压力循环系统,使工具电极中喷出高压工作液,使之更适应小孔加工的条件.以DMKT132精密数控电火花成型机床的改造为实例,说明机床改造前后加工小孔的变化,结果表明,用该方法加工小孔,加工效率平均提高一倍以上,提高了加工质量,具有广泛的推广价值.     

OFDM系统相关矩阵的分块结构及同步算法

根据载波加权可增强OFDM系统周期平稳性,实现系统盲同步的基本原理,分析了OFDM系统相关矩阵的分块结构,给出相应系统的盲同步算法.该方法通过检测相关矩阵的分块Toep litz矩阵结构,实现系统定时和载频偏差的估计.同时,在特定系统同步性能交换误码率的情况下通过分析载波加权、系统误码率和载频同步误差之间的互相制约关系,进一步给出了载波加权的确定方法.实验仿真结果表明,采用分块相关矩阵的同步方案与采用循环谱的同步方案相比,可获得更好的系统载频和定时同步效果.     

基于MAS的多机械手协调工作控制

为了解决全自动化晶体切片角分类机三个机械手协调工作的控制问题,设计了以MAS理论为基础的分布式网络控制器.系统利用黑板结构来实现全局动态目标下的状态信息的共享,采用多Agent理论对三个机械手进行协调工作控制,解决了机械手之间的运动耦合问题,使之能够在同一个时间和不同的空间内协调与配合工作,完成整体工作任务.基于此设计的设备可改善工人的劳动环境、提高生产效率、确保晶体切片切角的测量与分类准确.     

有限导流垂直裂缝产能及影响因素研究

从渗流理论出发,利用瞬时源、连续源的思想,结合卷积公式、Laphce变换等方法,建立了有限导流垂直裂缝井的产能计算模型,对模型导出的积分方程采用边界元方法(BEM)在Laplace空间进行了求解,利用Stehfest数值反演.获得了实空间的解,从而给出了准确计算有限导流垂直裂缝井产量的方法.此外,还通过定量计算分析了裂缝各设计参数对产量的影响方式和影响程度.通过分析可知,压裂井的日产量随裂缝长度、裂缝渗透率、裂缝宽度的增加而增大,但其产量增加的幅度随三种因素的增大而逐渐减小,因此在实际的油藏水力压裂设计时,应结合压裂成本和增益来考虑合适的设计参数.对压裂井产量预测和水力压裂油藏工程设计具有一定价值.     

适度出砂技术在海上稠油油田的应用研究

通过理论计算和室内出砂模拟实验,分别从地层出砂、井筒附近防砂以及井筒内的携砂生产三方面时适度出砂开采方式进行了研究.结果表明:地层出砂对储层物性有所改善,不同粒径段颗粒出砂1%后,渗透率增幅为20%左右,其中细微砂粒(<39 μm)的产出对渗透率提高贡献最大,为21,07%-37.60%;防砂管和地层环空间砂粒的堆积对产能影响很大,环空无砂时产能提高1.71倍,但当环空充满砂时产能仅提高14.70%;只有当井筒内的流体流速大于等于砂粒的沉降末速时产出砂才能被携带出井筒.该开采方式在渤海稠油油田得到成功应用.     

Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.     

Rotordynamic forces generated by discharge-to-suction leakage flows in centrifugal pumps

In order to investigate the flow-induced vibration in the shroud passage of centrifugal pump and predict rotordynamic forces of centrifugal pump rotor system,an analysis of rotordynamic forces arising from shrouded centrifugal pump is presented. CFD techniques were utilized to analyze the full three-dimensional viscous,primary/secondary flow field in a centrifugal pump impeller to determine rotordynamic forces. Multiple quasi-steady solutions of an eccentric three-dimensional model at different whirl frequency ratios yielded the rotordynamic forces. The skew-symmetric stiffness,damping,and mass matrices were obtained by second-order least-squares analysis. Simulation of the coupled primary/secondary flow field was conducted,and the complex flow characteristics in the flow field of a shroud passage were achieved including the mean velocity and pressure,as well as the eddy in a large scale of flow field due to viscosity. The rotordynamic force coefficients were calculated,and the results were in good agreement with those of experiment except for the direct inertial coefficient without the consideration of whirling forces from the impeller primary flow passage.     

Relationship of hydrocarbon and source-rock in Nos.3-5 tectonic belts of the Lenghu area, northern Qaidam Basin

Based on analyses of the components of crude oil hydrocarbons and carbon isotopes, the content of normal alkane de-creased from 49.00% to 20.10% when moving from the No.3 to No.5 tectonic belt of the Lenghu area of the Qaidam Basin, while cycloalkanes increased from 30.00% to 52.20% and aromatic and branch chain alkanes increased gradually as well. The maturity of sterane in crude oil is higher than that of its source-rock, which shows that the hydrocarbons were generated from a deep source-rock of high maturity around the tectonic belts of the Lenghu area. The analysis of the characteristics of carbon isotopes also shows that these isotopes of hydrocarbon compounds in the No.4 and No.5 tectonic belt are apparently heavier than those in the No.3 belt. The results of our research show that the hydrocarbons in the No.3 tectonic belt are mainly from a relatively rich sapropelic substance, while the hydrocarbons in the No.4 and No.5 tectonic belt originated mainly from organic matter of a rela-tively rich humic type substance.     

基于GPRS水管网无线监控系统设计

介绍了一种基于GPRS的供水管网监控系统的设计方法,选择了GPRS作为本系统的通信方式,利用工控软件组态王进行供水监控系统设计,以可编程控制器作为下位机实现供水管网的自动动态采集信号,对监控参数进行动态管理,完成现场设备的实时数据采集、远程数据传输等功能.