碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

多关节机器人通用体系结构的研究

结合一个五自由度教学工业两用型机器人应用实例，构造出多关节机器人通用体系结构，包括总体原型、机械结构、关节传动链、伺服驱动元件、电气控制系统、关节坐标系及其运动学方程、通信协议和软件设计思路等。通过实际使用表明，本文提出的通用体系结构是实用的、合理的。     

Preparation and properties of nanosize MnZn ferrite from δ-FeOOH

Ferrous ion was transformed into feroxyhyte (δ-FeOOH) by oxidation. Then, manganese sulfate and zinc sulfate in some ratio were added to the feroxyhyte solution. The co-precipitation was boiling reflux conditions sometime under constant stirring. The nanosize MnZn ferrite powder was formed. The mechanism of preparation of the nanosize MnZn ferrite was discussed, and the formation of feroxyhyte which was playing a key role during the process was mentioned. The properties of powder was tested by means of X-ray diffraction, transmission electron microscopy and vibrating sample magnetometer. The results show that the samples of spherical particles about 20 nm, which have characteristics of ferrimagnetism, has larger saturation magnetization, but the remanent magnetization and coercivity are comparatively smaller. The spinel MnZn ferrite nanosize powder was successfully prepared from δ-FeOOH at low temperature, with low-carbon steel and peroxide as main material.     

Analysis of Intermetallic Phases Formed on Surface Vapor Oxidized H13 Hot Work Steels in Molten Aluminum

In this paper, the author dipped surface vapor oxidized H13 steel specimens into 700℃ molten aluminum liquid for a certain period of time. Analyze the intermetallic phases formed on the H13 samples surface with optical microscope and X-ray diffraction method. The observation of immersion test sample's cross-section shows that Fe3O4 film will protect die substrate from molten aluminum erosion. The identification of the intermetallic phases reveals that they consist of 2parts, which is named as the composite layer and the compact layer. Further investigations are made in order to know the phase constituents of the 2 layers, they are Al8Fe2Si (outer composite layer), (AlCuMg) and Al5Fe2 (compact layer),respectively. The experimental results show that on the same specimen, a convex surface with bigger radius of curvature is more likely to be molten and the melting loss speed is also faster than a flat and smooth surface. The thickness of compact layer on a smooth surface is much bigger than that of the convex surface. Therefore, the author supposes the compact layer is favorable in stabilizing the die surface material from further melting loss, as their formation on the die surface, the melting loss speed will decrease.     

Effect of surface free energy on the adhesion of biofouling and crystalline fouling

Pipelines and heat exchangers using seawater as coolant suffer from biofouling. Biofouling not only reduces heat transfer performance significantly, but also causes considerable pressure drop, calling for higher pumping requirements. It would be much more desirable if surfaces with an inherently lower stickability for biofouling could be developed. In this paper, a cost-effective autocatalytic graded Ni-Cu-P-PTFE composite coating with corrosion-resistant properties was applied to reduce biofouling formation. The experimental results showed that the surface free energy of the Ni-Cu-P-PTFE coatings, which were altered by changing the PTFE content in the coatings, had a significant influence on the adhesion of microbial and mineral deposits. The Ni-Cu-P-PTFE coatings with defined surface free energy reduced the adhesion of these deposits significantly. The anti-bacterial mechanism of the composite coatings was explained with the extended DLVO theory.     

火焰原子吸收光谱法测定高纯石英粉中痕量钙

系统地研究了用空气——乙炔火焰原子吸收光谱分析法测定高纯石英粉中钙的最佳条件，建立了14％的乙醇作为增感剂，在2％盐酸介质中，0．4％ LaCl3溶液作为释放剂，用塞曼火焰原子吸收法测定的可行性方案，探讨了共存元素对钙的干扰及其消除。方法操作简便快速，干扰少，方法相对标准偏差小于3％，适用于日常分析石英粉中的杂质。     

无芯胶管的研制、工艺现状和发展建议

20世纪60年代初,我国胶管领域自主开发创新研制了无芯胶管制造技术,并且形成定型技术,一直沿用至今,笔者参与、见证了该产品从试验到投产的全过程。本文对该产品的工艺进行了新旧对比,提出了今后发展的建议。     

有限元方法在离心机转鼓强度分析中的应用

在回顾以往转鼓强度分析的基础上 ,指出了目前转鼓有限元应力分析所存在的问题 ,给出了提高计算精度和保证模拟有效性的注意事项 ,并探讨了转鼓强度评定准则     

碳铵化肥发青问题解决小结

探讨了该厂化肥生产中碳铵发青的原因,通过硫化氢含量的测定,分析了系统内外影响因素,提出了解决措施,达到了不停车稳定产品质量的目的。