一种提高嵌入式系统UBI分区挂载速度的设计方案与研究

根据Linux嵌入式系统UBI分区的挂载原理,在系统关机时预先扫描UBI设备中PEB块的相关头信息,并进行相关压缩处理后存储在UBI分区中的指定物理位置,使得系统下次开机时内核可直接读取预先存储的扫描信息,节省了大量时间.以关机时间换取开机速度的提高,在大量使用UBIFS的基于NAND flash嵌入式系统应用中有很好的优势.     

玻璃中离子注入的进展

玻璃中离子注入的进展王承遇，王波，陶瑛（大连轻工业学院玻璃及无机新材料研究所１１６００１）ＴｈｅＤｅｖｅｌｏｐｍｅｎｔｏｆＩｏｎ－ＩｍｐｌａｎｔｉｏｎｉｎＧ１ａｓｓｅｓ￥ＷａｎｇＣｈｅｎｇｙｕ；ＷａｎｇＢｏ；ＴａｏＹｉｎｇ（ＩｎｓｔｉｔｕｔｅｏｆＧｌ...     

Preparation of BaTiO3-Based Nonreducible X7R Dielectric Materials Via Nanometer Powders Doping

Nonreducible X7R dielectric materials, which can be cofired with Ni electrode, were obtained by doping nanometer additives to BaTiO₃ powders synthesized by employing a sol-gel method. The crystallization process, structure and constituent of nanometer additives, as well as morphologies were studied via differential thermal and thermogravimetric analyses (DTA/TG), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of the calcining temperature of dopants on the dielectric properties were also discussed. The experiment results proved that higher-performance X7R dielectric materials could be obtained via nanometer doping compared with conventional doping. At room temperature, dielectric constant is more than 3000; dielectric loss lower than 1.0% and insulation resistance more than 10¹¹Ω ⋅cm.     

Machinability of Metal Matrix Composites Reinforced by 3-D Network Structure

Metal matrix composites reinforced by three-dimensional (3-D) continuous network structure reinforcement (3DCNRMMC) are difficult to machine due to serious tool wear and poor surface roughness caused by the brittle and hard reinforcement which interpenetrate into ductile matrix. In order to achieve the approach of low cost of 3DCNRMMC, the machinability of it needs to be understood. The influences of three cutting parameters and volume fraction of reinforcement on cutting force were analyzed in detail. The results indicate that: (1) Due to the brittle phase(s) introduced into ductile matrix of composites, there is a large fluctuation of cutting force causing deterioration of machinability. The fluctuation ranges of cutting forces, initially increase rapidly with the increase of volume fraction of reinforcement and then decrease finally, are largest at the range of the volume fraction of 55–65%; (2) The influence of cutting parameters on cutting force is obvious. With the increases of cutting speed, cutting force decreases gradually unless cutting speed exceeds the value of 209 m/min. Cutting forces increase with increasing feed rate and depth of cut; (3) Owing to the large fluctuation of cutting force, there were some cratered surfaces caused by Si₃N₄ reinforcement pulling-out and flaking-off. Some brittle phase protruding from the machined surface caused the deterioration of machined surface.     

超细片状铝粉和铝银浆的制备

超细鳞片状铝粉和铝银浆由于其特殊的二维平面结构，具有良好的遮盖力、显著的屏蔽效应、光学反射能力；超细鳞片状铝粉和铝银浆颜料的制备方法很多，本文采用机械化学法制备超细鳞片状铝粉和铝银浆。     

汽轮机湿蒸汽参数在线计算方法的优化

优化改进了湿蒸汽参数计算的方法,将湿蒸汽计算单独使用的能量平衡法和曲线外推法相结合,通过嵌套式综合迭代,在保证精度的前提下,使迭代收敛速度显著提高.     

低速旋转机器振动测试与评价

低转速机器振动频率低、幅值小,测量困难.在考察转子的平衡情况时,不能仅通过振动幅值的大小来评价转子的平衡状况,而应该通过试加重量计算加重灵敏度以后,再计算出转子残余不平衡量并与标准要求值进行比较和判断.     

谱映像定理在欧氏空间中的另类证明

以泛函分析中的谱映像定量为基础,利用矩阵可以约化为若当型的特点,用一种非常简便的方法证明了欧氏空间中的谱映像定理,给出了一类矩阵指数特征值与原矩阵特征值之间的关系,并给出具体的实例验证结果的有效性.     

多元回归分析在电热式平板硫化机热板温度场中的应用

分析电热平板硫化机热板温差大的主要影响因素,重点研究热源分布情况对温差的影响.以400×400电热平板硫化机为例,应用多元回归的二次响应曲面模型及其子模型,对热源间距(电热管间距)与热板表面最大温差之间的函数关系进行预测,检验并分析预测结果(拟合曲线)的可靠程度,从而得出较合理的数学模型,即完整二次响应曲面模型.此模型可为工程设计提供参考依据.