Contact stresses in an infinite plate containing a smooth circular insert under thermal load

Summary. A solution is presented for the contact problem with a smooth circular elastic insert in an infinite, linearly elastic plate under thermal load. The thermal load considered here includes the temperature gradient applied at infinity and a uniform temperature change. One of the major difficult parts in solving the present problem is that separation may occur between an insert or inclusion and the surrounding matrix under a nonuniform expansion of the matrix and the insert due to a temperature change. Based on the complex potential theory and the method of analytical continuation, the problem is reduced to a singular integro-differential equation which is solved numerically. Results are presented for the contact angle and for the normal and circumferential stresses at the plate-insert interface. Exact solutions are found for the current problem for a special case when the material properties of the plate and the insert are identical.     

Pinpoint injection of microtools for minimally invasive micromanipulation of microbe by laser trap

This paper reports transportation of the target microbe by the laser trapped microtools with minimum laser irradiation to the target. The size of a microtool (MT) is around micrometer. The MTs are manipulated by the focused laser under the microscope to manipulate the target microbe. Here we propose a pinpoint injection method of MTs at the desired location in the microchamber, which is filled with liquid. At first, we classified the injection method of the MTs in four categories. Here we employed a new method to install the MTs inside the microchamber. We developed a MT holding chip to install the MTs. The MTs were injected in the microchamber, and were manipulated successfully by the laser scanning micromanipulator to transport the target microbe for separation. The proposed method is useful for the pinpoint injection of MTs and separation by the indirect micromanipulation.     

Hf-doped and NH/sub 3/-nitrided high-K gate dielectric thin film with least drain current degradation and flatband voltage shift

A novel technique to form high-K dielectric of HfSiON by doping base oxide with Hf and nitridation with NH/sub 3/, sequentially, is proposed. The HfSiON gate dielectric demonstrates excellent device performances such as only 10% degradation of saturation drain current and almost 45 times of magnitude reduction in gate leakage compared with conventional SiO/sub 2/ gate at the approximately same equivalent oxide thickness. Additionally, negligible flatband voltage shift is achieved with this technique. Time-dependent dielectric breakdown tests indicate that the lifetime of HfSiON is longer than 10 years at V/sub dd/=2 V.     

Photosensitivity of surface barrier structures based on Cu(In,Ga)Se<Subscript>2</Subscript> films grown by codeposition in vacuum

Polycrystalline Cu(In,Ga)Se₂ (CIGS) films with various ratios of Cu, In, and Ga were grown by codeposition of all elements in vacuum. The X-ray diffraction study showed that the films are single-phase and possess a chalcopyrite structure with predominant [112] orientation. The films exhibited a mirror smooth surface and had a close-packed structure composed of crystallites with clear faceting and a transverse size of 0.1–0.3 μm. Related surface barrier structures of the (In,Ag)/Cu(In,Ga)Se₂ type were obtained and their spectra of the quantum efficiency of photoconversion were studied. The obtained structures can be used for optimization of the CIGS film technology.     

A universal matrix solver for integral-equation-based problems

A new method has been developed for compressing the matrices that occur in most integral-equation-based computer programs. This method is easy to interface with existing computer programs, and allows them to run significantly faster and with significantly less memory. This method applies not only to electromagnetic and acoustic computation, but also to most programs involving a Green's function or any integral equation with a kernel having some smoothness properties. Our numerical computations, running on a high-end personal computer, have achieved compression ratios of fifty times, and compressed inversion of the matrices fifty times faster than by previous methods. For larger problems, solved on high-performance computers, these ratios would improve to about one thousand to one for larger moment method problems.     

A simple impulsiveness correction factor for control of electromagnetic interference in dynamic wireless applications

The emerging software defined radio technologies will be an enabler for a new generation of dynamic wireless systems. It will also open up the possibility of allocating frequencies in a, more dynamic way than today. From an intersystem-interference point of view, this can cause unforeseen problems to occur due to the increased complexity in such applications. In such applications, a measure indicating whether or not a frequency band is possible to use from an electromagnetic interference point of view, must be found. A simple approach is to use the measured total average interference power within the receiver band. Since the interference impact on modern digital communication systems from an interference signal does not only depend on the power but also on the actual waveform of the interference signal, some kind of quality measure of the average-power approach would be convenient to use. In this paper, we introduce a simple quality measure of the average-power approach so that a rough adjustment for the interference-waveform properties can be done.     

Waveguide probe structures for a multilayer magnetodielectric: An inverse problem

Direct and inverse problems are considered for diffraction by an open end of a rectangular waveguide (RW) with a flange that adjoins a piecewise inhomogeneous planar layered lossy medium. Also considered are similar diffraction problems for a junction of an RW and a rectangular resonator filled with a multilayer medium and a junction of two RWs, one of which contains a multilayer plate. Such open and shielded waveguide probe structures (WPSs) are used for determination and nondestructive testing of parameters of multilayer samples. The direct problem is formulated on the basis of admittance and impedance algorithms with consideration for losses existing in the medium, flange, and screens. In this case, the approximation of the given aperture field allows obtainment of explicit solutions for open and shielded WPSs in the form of integrals. Solution of the inverse problem that lies in determining thicknesses, permittivities, and permeabilities of the layers from measured values of the magnitude of the reflection coefficient is obtained by minimizing the corresponding least-squares error and by constructing artificial neural networks. In order to increase the accuracy, it is proposed to use a two-port of errors and perform measurements for several positions of the sample with respect to the flange and different impedance conditions behind the sample.     

The colored revolution of bioimaging

This paper provides an overview of the main aspects of modern fluorescence microscopy. It covers the principles of fluorescence and highlights the key discoveries in the history of fluorescence microscopy. The paper also discusses the optics of fluorescence microscopes and examines the various types of detectors. It also discusses the signal and image processing challenges in fluorescence microscopy and highlights some of the present developments and future trends in the field.     

Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Transient response of ARROW VCSELs under external optical feedback

The effect of external optical feedback on the transient response of antiresonant reflecting optical waveguide (ARROW) vertical-cavity surface-emitting lasers (VCSELs) is studied. It can be shown that the proper design of ARROW can suppress the excitation of high-order transverse leaky mode as well as increase the critical feedback strength so that stable high-power single-mode operation of VCSELs can be obtained even under the influence of strong external optical feedback.