Crack initiation and propagation induced by inclusions in a nickel-base P/M superalloy under fatigue load

1 IntroductionRecently the key components in advanced aircraftengines are widely made of nickel-base P/M super-alloy. However, non-metallic inclusions are intro-duced into this material during powder metallurgyprocessing. In industry, although many method…     

锆基块体非晶合金的力学性能研究进展

本文叙述了锆基块体非晶合金的制备方法，优异的性能，特别是对其力学性能研究领域的最新进展进行了综述。并与传统晶态合金作了适当的对比，锆基块体非晶合金具有优异的力学性能，如弹性比功、超塑性、断裂韧性等，此类合金的应用将不断拓宽。     

呋喃树脂砂生产大型柴油机底座气孔缺陷的防止

底座是大型柴油机的关键件,主要作用是安装曲轴和支撑整个柴油机,并盛放润滑油,外形尺寸为:2 420 mm×1 080 mm×610 mm,主要壁厚为10～12 mm,见图1.材质为HT250,重量2 500 kg,要求常压密封性试验,保持30 min不渗漏.     

铝合金板材时效组织的高分辨分析

本文通过X射线衍射、扫描电镜、高分辨透射电镜,分析了6009铝合金时效组织,球形Mg2Si是其主要强化相。在电解低钛铝合金中,球形Mg2Si分布更为弥散、均匀。对高分辨像通过傅立叶变换和反傅立叶变换,得到了调幅分解组织的晶格像。结果表明:电解低钛铝合金其力学性能和组织优于熔配加钛铝合金;电解低钛铝合金中Mg和Si原子在铝基体的(200)面上偏聚,形成明显的调幅分解组织。     

EFFECT OF ALLOY ELEMENTS ON QUASIEQUILIBRIUM MICROSTRUCTURE IN Fe-Mn-Ni-Cr STEELS

The microstructures of Fe-Mn-Ni-Cr steels with medium carbon and the effect of alloy ele-ments on them have been investigated by means of X-ray diffraction quantitative phase ana-lyses,metallography and hardness tests.The volume fraction of martensite in steels quenchedat 1100℃ can be expressed as:f_M~(1100)=162.643-15.482Mn-7.36Ni-4.286(Cr+Mo+V)Based on this expression,the quasi-equilibrium microstructure diagram has been obtained.Itis shown that the effect of Mn on the austenite stability is greater than that of Ni.The equiva-lent [Ni]=2.104Mn+Ni and equivalent [Cr]=Cr+Mo+V.The driving force for martensite transformation at M_s point has been calculated to hedrastically decreased by element Mn.     

QUASI-EQUILIBRIUM MICROSTRUCTURES AND EFFECT OF ALLOY ELEMENTS IN Fe-Mn-Ni-Cr STEELS

本文利用X射线定量相分析及金相观察和硬度测试,考察了中碳Fe-Mn-Ni-Cr钢的组织及合金元素的作用。建立了经1100℃淬火后的马氏体体积分数与合金成分的定量关系式; f_M~(1100)=162.643-15.482Mn-7.36Ni-4.286(Cr+Mo+V)并在此基础上给出了亚平衡组织图。结果表明,Mn稳定奥氏体的作用大于Ni的作用。Ni和Cr当量分别以[Ni]=2.104Mn+Ni,[Cr]=Cr+Mo+V表示。计算了M_S点处的马氏体相变驱动力,指出Mn具有强烈降低相变驱动力的作用。     

HIGH TEMPERATURE LOW CYCLIC FATIGUE BEHAVIOUR OF DIRECTIONALLY SOLIDIFIED Ni-BASE ALLOY DK3

研究了镍基定向凝固高温合金DK3和普通铸造合金K3在760℃应变控制和应力控制下的高温低周疲劳行为。结果表明:这两种合金的高温低周疲劳行为可以用常规的应力疲劳曲线来表征。DK3合金不存在“过渡疲劳寿命”N_T,K3合金则很低。在各种不同应变或应力水平下,DK3合金的低周疲劳寿命高于K3合金,当应力水平为785至980MPa时,其寿命约差1倍,当应力水平为490至685MPa时,则差2倍多。     

人工智能在冷轧带肋钢筋工艺参数优化中的应用

论述了人工智能在冷轧带肋钢筋工艺参数优化中的应用,首先利用神经网络建立起冷轧带肋钢筋工艺参数与产品抗拉强度之间关系的数学模型,然后用遗传算法对工艺参数优化。按优化后的工艺参数在某拉丝加工厂进行了大批量生产试验,产品的合格率达到98%以上,从而为控制冷轧带肋钢筋工艺参数提供了一条行之有效的途径。     

Quantification of trace amounts of impurities in high purity cobalt by high resolution inductively coupled plasma mass spectrometry

An analytical method using high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) for rapid simultaneous determination of 24 elements (Be, Mg, Al, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Ge, As, Se, Mo, Ag, Cd, Sn, Sb, Ba, Pt, Au, and Pb) in high purity cobalt was described. Sample digestions were performed in closed microwave vessels using HNO3 and HCl. The matrix effects because of the presence of excess HCl and Co were evaluated. The usefulness of high mass resolution for overcoming some spectral interference was demonstrated. The optimum conditions for the deter- mination were tested and discussed. The standard addition method was employed for quantitative analysis. The detection limits were 0.016-1.50 μg?g?1, the recovery ratios were 92.2%-111.2%, and the RSD was less than 3.6%. The method was accurate, quick, and convenient. It was applied to the determination of trace impurities in high purity cobalt with satisfactory results.