Rapid and comprehensive indicator for evaluation of performance of treatment processes and of river waters.

Naturally occurring UV active compounds, commonly present in almost all source waters, can be rapidly monitored by their ultraviolet absorbance at 260 nm (E260). Herein, the extent of correlation between the E260 and the removal efficiency of the hazardous contaminants, endocrine disrupters and dioxins, were investigated using various treatment and river source waters. The detection of various types of hazardous contaminants using sophisticated analytical methods, such as high resolution gas chromatography (HRGC)/high resolution mass spectrometry (HRMS) and high performance liquid chromatography (HPLC)/inductively coupled plasma (ICP)/mass spectrometry (MS), as well as various short-term bioassays, can require hours or even days for results to be obtained. The removal of the E260 correlated well with those of individual contaminants, such as endocrine disruptor chemicals and dioxins, with the various treatment processes employed. In the plots of the endocrine disrupters against the DOC/E260, a correlation was found with the endocrine activity of the Korean/Japanese river waters employed in this study.     

A VLSI CMOS delay oriented waveform converter for polyphasefrequency synthesizer

In this paper, we present a waveform converter implemented on a 0.25-μm CMOS technology using a dedicated design methodology (Delay Oriented Design). The circuit converts a square wave signal in both in-phase and quadrature-phase sinusoidal differential outputs. It also multiplies the frequency by seven. The output frequency range of this converter extends from 1.05 GHz up to 2.17 GHz. This converter is dedicated for the design of a third-generation mobile phone synthesizer using a double-loop architecture. For an output frequency of 2 GHz, the measured phase noise at 10-kHz offset from the carrier is -97 dBc/Hz. The circuit consumes 50 mW from a 2.5-V supply     

Modelling thermal degradation of composite materials

A one–dimensional, transient thermal degradation heat transfer model for the response of composite materials when exposed to fire is presented. The model can handle layers of different materials. Material properties are functions of temperature. The reaction can be specified using Arrhenius‐type parameters or by inputting a density–temperature relationship determined by any experimental technique such as thermogravimetric analysis. The model is validated against the experimental data presented in Boyer's 1984 dissertation. Overall, the model provides excellent agreement with the experimental data. It is shown that very little difference is found between results arrived at by Arrhenius kinetics and results obtained by specifying the easier to measure density–temperature relationship. From this it is concluded that this technique is a viable alternative to Arrhenius‐type models. Copyright © 2006 John Wiley & Sons, Ltd.     

Effect of the Treatment Temperature on the Surface Drying Set of Sugi Boxed-Heart Square Timber

High-temperature and controlled humidity treatment before drying has proven to be highly effective in preventing surface checks by forming drying sets in the surface layer of boxed-heart square timber in Japan. In this study, we examined the differences of the surface drying sets on sugi timber under different treatment temperatures. As a result, the width of a surface check after drying was much smaller at a treatment temperature of 120°C than at 80°C, and this indicates that the drying set with 120°C treatment would be larger than that with 80°C treatment. Also we observed that treatment temperature had a greater effect on the drying set as the drying advanced.     

High-temperature sensible-heat storage options

Alkali-metal carbonate salts meet the requirements for high-temperature solar central receiver systems, but because of their corrosiveness they present special problems in the design of storage tanks. In order to reduce corrosion and temperature sufficiently to retain strength in the storage containing wall, internal and thermal insulation is required. We present design options and operation criteria for sensible-heat, molten-salt storage with internal insulation.     

宝鸡市医用诊断X线照射频度调查

本文报道从1984年6月1日至1985年5月31日对宝鸡市五县(区)医用诊断 X 线照射频度的调查结果。结果表明,胸透和群检胸透医照率最高,占医疗照射总人次数的68.7%,门诊医照率为70.8人次/千人·年,人群受照率为344。5人次/千人·年。按年龄比较,青壮年组医照率最高,占医照总人次数的57.2%。按性别比较,男性多于女性。     

Mechanism of resistance microwelding of crossed fine nickel wires

Resistance microwelding of fine crossed nickel wires is of increasing industrial importance for electrical connections in downsized electronic and medical devices, but the understanding of the process is very limited. A study has, therefore, been performed to clarify the basic joining mechanisms, in which the effects of main process parameters (welding current and force and weld time) were investigated by detailed mechanical testing and metallurgical examinations. A bonding mechanism with main process stages (wire cold collapse, surface melting, molten-phase squeeze-out and, solid-state bonding) was proposed. A new technique has also been developed to optimize the process by initiating the welding current well before the electrode force has reached its full nominal value.     

Single-Threaded vs. Multithreaded: Where Should We Focus?

Today, with the increasing popularity of multicore processors, one approach to optimizing the processor's performance is to reduce the execution times of individual applications running on each core by designing and implementing more powerful cores. Another approach, which is the polar opposite of the first, optimizes the processor's performance by running a larger number of applications on a correspondingly larger number of cores, albeit simpler ones. The difference between these two approaches is that the former focuses on reducing the latency of individual applications or threads (it optimizes the processor's single-threaded performance), whereas the latter focuses on reducing the latency of the applications' threads taken as a group (it optimizes the processor's multithreaded performance). The panel, from the 2007 Workshop on Computer Architecture Research Directions, discusses the relevant issues.