Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Quantitative determination of aflatoxin B1 in chick liver

A method for the rapid and quantitative determination of aflatoxin B1 from small quantities of liver, around 1-2 g, is described. The extraction procedure involves acidification to pH 2 of the aqueous liver homogenates, extraction with chloroform: acetone and HPLC-fluorimetric detection after derivatization with trifluoroacetic acid. Quantitative recovery of aflatoxin B1 from chick liver was achieved and detection at levels of 0.2-1 ppb was proved feasible. The aflatoxin B1 concentration in chick liver after oral administration is also shown.     

Interfacial strength and chemistry of additive-free silicon nitride ceramics brazed with aluminium

Two kinds of additive-free silicon nitride ceramics were brazed with aluminium; one was with as-ground faying surfaces and the other was with faying surfaces heat-treated at 1073K for 1.8 ksec in air. The heat-treatment of the silicon nitride ceramics formed a silicon oxynitride layer on the faying surfaces and increased the brazing strength of the joints. A silica-alumina non-crystalline layer and a β′-sialon layer were formed successively from the aluminium side at the interface of the joints. The heat-treatment which made the former layer thicker is a necessary process in making reliable, strong brazed joints.     

Influence of initial growth layer and Ti underlayer on magneticproperties and recording characteristics of very thin films ofevaporated Co-Cr media

A Co-Cr film deposited directly on a substrate has an initial growth layer with low coercivity. However, the existence of a Ti underlayer prevents the formation of such a layer. As a result, Co-Cr film deposited on a Ti underlayer has high perpendicular anisotropy and coercivity even in cases of extremely thin film thickness (200 Å). As for the read-write characteristics of Co-Cr thin-film media, the existence of such an initial growth layer greatly improves the reproduced output level. The cause for this is considered to be that the free charges which appear on the back surface of the perpendicular recording layer are reduced and the demagnetization field acting on the recorded magnetization subsequently decreases due to the existence of the initial growth layer     

Nonlinear static and dynamic analysis of circular plates and shallow spherical shells using the collocation method

The present work investigates the efficacy and applicability of interior global orthogonal point collocation method to the axisymmetric nonlinear analysis of elastic circular plates and shallow spherical shells subjected to uniformly distributed transverse load. Spacewise discretisation has been carried out using a polynomial expansion with the zeros of a Chebyshev polynomial as collocation points. Timewise integration has been carried out with Newmark k-β scheme corresponding to average acceleration method. The static response and snap-through buckling results, as well as, the dynamic response and dynamic buckling results under a uniformly distributed step load have been obtained and found to agree closely with the available results.     

An alternating technique for evaluating weight functions for 3-D surface flaws in finite solid bodies

An efficient method, based on the Schwarz–Neumann alternating technique, is presented for computing weight functions of a general solid (3-D as well as 2-D), with embedded or surface-flaw configurations. The total rate of change of the crack-opening displacements, due to simple perturbations of crack-dimension characteristics, is conveniently decomposed into the infinite-domain and boundary-correction parts. The former is determined from available analytical solutions of ideal-shaped cracks, whereas the latter is computed numerically by imposing nil boundary-traction requirements for the displacement field corresponding to the weight functions. Numerical examples, with solutions for 3-D weighted-average and local stress intensity factors, indicate that the proposed method is very accurate and efficient.     

Repulsive Flux Pinning Force in NbTi/Nb Superconductor/Superconductor Multilayers

Flux pinning characteristics have been investigated for the Nb _x Ti_100-x /Nb(x = 65, 50 and 28) and Nb ₂₈ Ti ₇₂/Nb ₆₅ Ti ₃₅ superconductor(S)/superconductor(S^′) multilayers. The maximum of the pinning force F _{p⊥ max} perpendicular to the layer plane as a function of the structure modulation length λ has a peak in the quasi-two-dimensional region (λ～20 nm). The maximum. values of the F _{p⊥ max} versus λ curve are proportional to the difference of the GL coherence length (ξ _GL ) between the superconductive sublayers S and S^′. The results suggest that the large F _{p⊥ max} in the S/S^′ multilayer is caused by the repulsive pinning force due to Nb layers with larger ξ _GL .