海上采油作业安全灭火措施--推广采用高倍泡沫灭火技术

对海洋石油平台火灾进行分析 ,提出采用高倍泡沫灭火技术与密集水流相结合的优化灭火措施建议 ,并介绍锦州 93平台应用实例     

Fracture behaviour of unmodified and rubber-modified epoxies under hydrostatic pressure

The fracture toughness and uniaxial tensile yield strengths of unmodified and CTBN-rubber-modified epoxies were measured under hydrostatic pressure. The purpose of these experiments was to learn how suppressing cavitation in rubber particles affects the deformation mechanisms and the fracture toughness of rubber-modified epoxy. It was found that the cavitation of CTBN-rubber could be suppressed at a relatively low pressure (between 30 and 38 M Pa). With cavitation suppressed, the rubber particles are unable to induce massive shearyielding in the epoxy matrix, and the fracture toughness of the rubber-modified epoxy is no higher than that of the unmodified epoxy in the pressure range studied. Unmodified epoxy shows a brittle-to-ductile transition in fracture toughness test. The reason for this transition is the postponement of the cracking process by applied pressure.Work performed while on a sabbatical leave at the University of Michigan.     

利用最小熵法预测高频拓宽频带

本根据最小熵观点给出了预测高频成分拓宽频带的方法，实际效果表明，该方法是一种拓宽频带的有效方法。     

一维波动方程反演波阻抗的实现及效果

利用波动方程反演波阻抗，由于计算工作量大、稳定性差等原因，一直没有在地震勘探资料处理中得到实际应用。本文提出的一维波方程逐段折叠反演方法能较好地克服上述缺陷，具有计算量相对较小、精度高、稳定性好等特点。并在大庆长垣东部和西部的实际资料处理中见到了良好的效果。     

温度调谐LBO晶体光参量振荡器

本文详细研究０．５３２μｍ激光泵浦、温度调谐Ⅱ型非临界相位匹配ＬＢＯ光参量振荡器。当温度从２０℃升高到２００℃时，其信号波和闲置波的调谐范围分别为１．００２～０．８９８μｍ和１．１３４～１．３０６μｍ。本装置最吸引人之处是本征输出线宽比Ⅰ型情形小一个量级。     

利用空间多普勒调谐技术冷却原子及其速度单一化

本文理论计算了用圆锥管内多次全反射激光而产生的多普勒频移来冷却原子束的机制。给出了最佳冷却原子束的圆锥管的夹角、长度、反射次数及激光入、出射角等参数。理论计算了原子束经过圆锥管冷却的速度分布情况。数值计算结果表明：采用两个长１３０ｃｍ的锥形管来冷却原子束，选用合适的失谐量可使极大部分速度小于１２００ｍ／ｓ的原子冷却到８ｌｍ／ｓ，并且可得到单一速度的高亮度的原子束。     

Protocol design and performance analysis for manufacturing messagespecification: A Petri net approach

The manufacturing message specification (MMS) is the ISO standard communication protocol specific to manufacturing. To analyze MMS design and performance, service unit automats are introduced to represent individual MMS services, while service connection Petri Nets (PNs) are constructed from these automats to describe MMS service connections and processes. This approach makes MMS protocol specification and analysis possible in terms of well-developed concepts and methods in PN theory. It leads to a distributed and hierarchical model of MMS software system by integrating service connection PNs. A generalized stochastic PN for MMS performance evaluation is obtained by incorporating service parameters and time factors into the model. A technique based on T-invariants is used to simplify the performance analysis     

Suppression of boron penetration in p+ polysilicon gateP-MOSFETs using low-temperature gate-oxide N2O anneal

It has been reported that high-temperature (~1100°C) N₂ O-annealed oxide can block boron penetration from poly-Si gates to the silicon substrate. However, this high-temperature step may be inappropriate for the low thermal budgets required of deep-submicron ULSI MOSFETs. Low-temperature (900~950°C) N₂O-annealed gate oxide is also a good barrier to boron penetration. For the first time, the change in channel doping profile due to compensation of arsenic and boron ionized impurities was resolved using MOS C-V measurement techniques. It was found that the higher the nitrogen concentration incorporated at Si/SiO₂ interface, the more effective is the suppression of boron penetration. The experimental results also suggest that, for 60~110 Å gate oxides, a certain amount of nitrogen (~2.2%) incorporated near the Si/SiO₂ interface is essential to effectively prevent boron diffusing into the underlying silicon substrate     

Enhancement of oxide break-up by implantation of fluorine inpoly-Si emitter contacted p+-n shallow junctionformation

In this study, it is demonstrated that the incorporation of fluorine can enhance poly-Si/Si interfacial oxide break-up in the poly-Si emitter contacted p⁺-n shallow junction formation. The annealing temperature for breaking up the poly-Si/Si interfacial oxide has been found to be as low as 900°C. As a result, the junction depth of the BF₂-implanted device is much larger than that of the boron-implanted device     

钒冶炼焙烧添加剂选择研究

对小型钒冶炼厂焙烧工艺所用添加剂进行改进的可能性进行了探讨，研究了几种常用添加剂的焙烧条件，分析比较了其性能，提出用ＮａＣｌ－Ｎａ２ＣＯ３作焙烧添加剂替代ＮａＣｌ可大幅度减少大气污染，提高冶钒转化率；且不改变工艺流程，无需设备投资，具有较好的经济效益和环境效益。