Correlation study on infrared thermography and nerve root signs in lumbar intervertebral disk herniation patient: a short report

OBJECTIVE: To determine whether infrared skin thermography is an objective measurement reflecting the seriousness of nerve root irritation in lumbar disk herniation patients. DESIGN: Quantified nerve root signs by physical examination were collected from the patients along with the infrared skin temperature measurement on the lumbosacral region and posterior part of thighs. A correlation study was applied to observe the relation between the nerve root signs and the skin temperature before a successful conservative treatment (mainly spine manipulation), and between the alteration of nerve root signs and that of skin temperature after the treatment. SETTING: Hospitalized care. PATIENTS: Twenty-seven hospitalized samples with computed tomography or magnetic resonance approval were consecutively selected during the latter half of 1990. MAIN OUTCOME MEASURE: Changes in nerve root signs. RESULTS: The temperature difference between a troubled thigh and healthy one is significantly correlated to the score of the nerve root signs before the treatment; and the reduction of temperature difference between two thighs is also significantly correlated with decreasing score of nerve root signs after the treatment. The correlation between the temperature difference on the left and right sides of the lumbosacral region and the nerve root signs before the treatment is insignificant; and the variation of the temperature difference of the same region after the treatment is not correlated with the decreasing score of the nerve root signs. CONCLUSION: Infrared skin thermography of lower extremities might be an objective sign in signaling the soothing process of the nerve root irritation in lumbar disk herniation patients, which may help a doctor in checking the responses of the patient to treatment.     

关于生物系统超微弱发光的实验研究

生物系统存在超微弱光子辐射现象。通过一系列实验研究,我们认为,这种光子辐射既有低水平化学发光的性质,又有受激辐射的性质,是受激的低水平化学发光。     

焊接史

本文追溯了19世纪末发明的电弧焊接的历史。当Oscar Kjellberg成立伊萨公司以探索他发明的涂层焊条时，伊萨从一开始就和电弧焊的发展结下了不解之缘。     

非接触型光外差轮廓仪

本文介绍一种纳米级非接触型高精度光外差轮廓仪,它是基于普通光路的光外差干涉仪。工件表面被两束有微小频差的激光束所照射,其中一束经聚焦后用作测量光探针来扫描工件表面,另一束则用作参考光束。两束光经表面反射后产生干涉。测量信号和参考信号的相位差与表面的微不平值成正比。仪器的横向分辨率为2μm,高度分辨率为1 nm,它不需要对试样作大范围的调整,且可用试样自身作参考面。信号经光电转换后由微型计算机进行处理,它能快速完成测量、计算、显示及打印出各种参数和曲线。     

丰满流域可能最大暴雨与可能最大洪水分析研究

依据丰满漉域的水文气象资料,计算丰满流域可能最大暴雨,推求白丰区间的可能最大洪水并进行成果合理性分析.     

Multistage amplifier topologies with nested Gm-Ccompensation

This paper presents a multistage amplifier for low-voltage applications (<2 V). The amplifier consists of simple (noncascode) low gain stages and is stabilized using a nested transconductance-capacitance compensation (NGCC) scheme. The resulting topology is similar to the well known nested Miller compensation (NMC) multistage amplifier, except that the proposed topology contains extra G _m feedforward stages which are used to enhance the amplifier performance. The NGCC simplifies the transfer function of the proposed multistage amplifier which, in turn, simplifies its stability conditions. A comparison between the NGCC and NMC shows that the NGCC has wider bandwidth and is easier to stabilize. A four-stage NGCC amplifier has been fabricated using a 2-μm CMOS process and is tested using a ±1.0 V power supply. A dc gain of 100 dB has been measured. A gain bandwidth product of 1 MHz with 58° of phase margin and power of 1.4 mW can be achieved. The op amp occupies an active area of 0.22 mm². Step response shows that the op amp is stable     

Boundary Constrained Swept Surfaces for Modelling and Animation

Due to their simplicity and intuitiveness, swept surfaces are widely used in many surface modelling applications. In this paper, we present a versatile swept surface technique called the boundary constrained swept surfaces. The most distinct feature is its ability to satisfy boundary constraints, including the shape and tangent conditions at the boundaries of a swept surface. This permits significantly varying surfaces to be both modelled and smoothly assembled, leading to the construction of complex objects. The representation, similar to an ordinary swept surface, is analytical in nature and thus it is light in storage cost and numerically very stable to compute. We also introduce a number of useful shape manipulation tools, such as sculpting forces, to deform a surface both locally and globally. In addition to being a complementary method to the mainstream surface modelling and deformation techniques, we have found it very effective in automatically rebuilding existing complex models. Model reconstruction is arguably one of the most laborious and expensive tasks in modelling complex animated characters. We demonstrate how our technique can be used to automate this process.     

在3．39μm波段甲烷吸收特性的测量与应用研究

报道了甲烷气体在３．３９μｍ波段吸收特性的研究结果，及其在３．３９μｍ波段多波长干涉测量中的应用。通过改变甲烷吸收室的充气参数，使激光器工作在双等光强工作点，并完成了绝对距离的干涉测量。