Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Effect of vibration condition and inter-particle frictions on the packing of uniform spheres

We present a numerical study of the packing of uniform spheres under three-dimensional vibration using the discrete element method (DEM), focusing on the effects of vibration condition (amplitude and frequency) and inter-particle frictions (sliding and rolling frictions). The results are analysed in terms of packing density, coordination number (CN), radial distribution function (RDF) and pore structure. It is shown that increasing either the vibration amplitude or frequency causes packing density to increase initially to a maximum and then decrease. Both vibration frequency and amplitude should be considered to characterize the effect of vibration process on packing structure. The sliding and rolling frictions between particles can decrease packing density since they dissipate energy, although the effect of rolling friction is less significant. In line with the change of packing density, microstructural properties such as CN, RDF and pore distribution also change: a looser packing often corresponds to smaller CN, less peaked RDF and larger but more widely distributed pores.     

Application of Support Vector Machines in Assessing Conceptual Cost Estimates

Total conceptual cost estimates and the assessment of the quality of these estimates are critical in the early stages of a building construction project. In this study, the support vector machine (SVM) model for assessing the quality of conceptual cost estimates is proposed, and the application of SVM in construction areas is investigated. The results show that the SVM model assessed the quality of conceptual cost estimates slightly more accurately than the discriminant analysis model. This shows that using the SVM has potential in construction areas. In addition, the SVM model can assist clients in their evaluation of the quality of the estimated cost and the probability of exceeding the target cost, and in their decision on whether or not it is necessary to seek a more accurate estimate in the early stages of a project.     

Control of calcium hexaluminate grain morphology in in-situ toughened ceramic composites

The influence of processing conditions on the morphology of calcium hexaluminate (CA₆) grains in Al₂O₃: 30 vol% CaO·6Al₂O₃ (CA₆) ceramic composites was investigated. Specimens were prepared by in-situ reaction sintering using precursor powders of alumina, and either calcium carbonate or calcium oxide. In some samples, 1 vol% anorthite glass was added as a sintering aid. X-ray diffraction was used to study the phase development in the as-calcined and sintered states. The resultant microstructures were characterized using both scanning electron microscopy (SEM), and imaging secondary ion mass spectrometry (SIMS). It was found that the CA₆ grains developed a platelike morphology when CaCO₃ was used as the starting calcium-rich powder. In contrast, samples prepared using CaO resulted in equiaxed CA₆ grains. This result was observed to be independent of the anorthite glass addition. The findings are rationalized in terms of distinct CA₆ reaction mechanisms, resulting from differences in the reactivity of the powders during the early stages of calcining.Cement Nomenclature C CaO - A Al₂O₃     

铸铁热分析用试样新型激冷剂的实验研究

从冷却曲线上相变段倾角最小原则出发，研究了新型激冷剂的配比与热分析法检测铸铁成分精度的关系，实验结果表明，能使相变段倾角最小的成分配比，也能提高对铸铁成分的热分析和检测精度。     

片状陶瓷材料高低温电性能参数的自动检测

由进口电性能仪配上自制的高温系统，计算机自动采集数据，配置成一套高低温电性参数测定装置，该装置的特点是，升温快，炉体小巧，炉芯可更换盛液氮装置，屏蔽良好，等温区长，温工及参数测量精确可靠。     

带中间接轴风机转子的找中心方法

提出了两种带中间轴风机转子的找中心方法,并通过实例得出了最佳方法.     

数字频率合成技术在地球站中的应用

数字分频式微波频率合成器,具有结构简单,造价低,良好的低相嗓特性等优点,因而被通信卫星地球站所广泛采用。论述了数字分频式频率合成技术在工星通信地球站中的应用,提出了采用高度集成锁相环器件:PE3336设计一种低相噪特性的微波数字频率源的工程实例,并将之用于某通信卫星转发器地球站设备中。     

DF_4内燃机车柴油机润滑油的热重分析

通过对DF_4内燃机车柴油机润滑油的热重曲线TG和微商热重曲线DTG的分析,探讨了这种润滑油的衰变规律。     

客户机／服务器计算环境

本文介绍了客户机／服务器计算环境的基本概念和产生背景，阐述了客户机／服务器计算中操作系统的选择原则及企业级客户机／服务器计算环境的特点。