Specific interactions in blends containing Chitosan and functionalized polymers. Molecular dynamics simulations

Chitosan (CS)/poly(vinyl alcohol) (PVA) and Chitosan/poly(2-hydroxyethyl methacrylate) (P2HEM) blends have been studied through molecular dynamic simulations. In a previous work it was found miscibility between these polymers and it was attributed to hydrogen bonding formation. However, the experimental information obtained was not enough to know which of the interacting groups of Chitosan, i.e. -CH₂OH or -NH₂, are responsible of the interaction. Therefore, we have performed molecular dynamics simulation runs of 1 ns in order to calculate radial distribution functions (RDF) for the groups tentatively involved in the interaction. The results are correlated with our previous experimental data. This way, we have obtained a more precise conclusive information about the interactions involved as function of the blends composition. For low compositions of PVA and P2HEM the interaction is predominantly with the hydroxymethyl groups of CS while as the composition of PVA and P2HEM increases, the interaction with the amine groups increases.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Molecular weight effect on the obtainment of parallel and perpendicular orientation in thermotropic poly(diethylene glycol <Emphasis Type="Italic">p,p′</Emphasis>-bibenzoate)

Summary The effect of molecular weight on the uniaxial orientation process has been analyzed in two samples of thermotropic poly(diethylene glycol p,p′-bibenzoate), evaluating the influence of that parameter on the type of orientation obtained. Several strain rates and deformation temperatures have been tested in order to map out the conditions for obtaining the two different kinds of orientation. The results show that in the lower molecular weight PDEB sample (M_w=31200) it is rather easy to get exclusively perpendicular “anomalous” orientation, with the molecular axes aligned transversely to the stretching direction. However, it is extremely difficult to obtain 100% parallel “normal” orientation. On the contrary, either type of orientation or a mixture of them can be easily developed for the higher molecular weight PDEB sample (M_w=102900).     

阴离子表面活性剂测定方法的探讨

本文对“阴离子表面活性剂的测定方法”进行探讨,优化了显色剂、萃取剂的用量及萃取频率等分析条件,有效地降低了方法的检出浓度,提高了分析精度及准确度,节约大量试剂。本法最低检出浓度的0.019mL/L。     

基于XML的基金会现场总线设备描述技术

本文简单介绍了基金会现场总线FF的设备描述和新一代稳定、可靠、通用的网络标记语言XML的特点，提出了一种用XML语言实现设备描述的方法。     

Effect of Heat Treatment on Luminescent Properties of White Organic Light Emitting Device

The white organic light emitting device (OLED) with single-structure using a polymer blend as the light emitting layer is fabricated. Heat treatment is used to control the ratio between the intensities of main electroluminescent spectral peaks. The electroluminescent spectrum of our device is quite similar to that of white inorganic LED produced by Nichia Corporation after being annealed, and its turn-on voltage can be decreased by 1V.     

基于随机相位误差Tikhonov分布的MC-DS-CDMA系统性能分析

本文针对工作于慢变频率选择性Rayleigh衰落信道中的部分相干的MC-DS-CDMA系统，基于随机相位误差的Tikhonov密度分布提出了误码率上边界的一种分析方法。仿真结果表明，随着环路信噪比的增加，相位误差损耗所产生的系统误码率性能损失变得越来越小，当环路信噪比高于系统信噪比(Eb/N0)20dB时，系统误码率性能损失小于0．2dB。在MC-DS-CDMA系统中，由于能用频率分集取代路径分集，因而接收机结构更易实现。     

Multi-antenna scheme for high capacity transmission in the digital audio broadcasting

In this paper, we apply multi-antenna scheme to DAB system for high-rate transmission. In the MIMO-DAB system with a number of transmitting and receiving antennas increases the transmission rate efficiently with low multiplication operations. For channel estimation in the MIMO-DAB system, we propose a new PRS structure and evaluate the channel estimation performance. The proposed PRS structure can estimate multi-channel information based on the semi-blind processing. The performance of proposed PRS is compared with that of conventional training sequence employing Tarokh's transmission matrix. And also we investigate the performance limitation due to the imperfect channel estimation in a MIMO-DAB receiver. It has been shown that the MIMO-DAB system with multi-antennas can achieve the high-rate transmission for multimedia broadcasting and the performance of MIMO-DAB system is impaired by imperfect channel information.     

Case Study-Based Challenges of Quality Concrete Finishing for Architecturally Complex Structures

This paper focuses on the procedure utilized in the construction of tilt-up irregular concrete panels that are constructed on-site using concrete slabs and wooden formwork. The case study required high-quality concrete finishing. The erection and installation procedure called for a maximum panel-to-panel joint tolerance of 1.27?cm (0.5?in.), often 90° joints between panels. To meet precision requirements, the casting slabs were leveled and flattened with laser screed technology and smoothed with chemical solutions. To ensure that the final result met expectations, a mock-up model was built using different types of materials and to simulate site constraints. The architectural design is a composition of precast concrete panels like “Lego” pieces assembled similarly to a jigsaw puzzle. The unique construction process required a state-of-the-art analysis to produce the set quality. Quality conditions as set by the owner included creating a smooth concrete surface on all panels while avoiding damages and reducing equipment and material costs. The proposed methodology is described through its implementation on the case study, which is also described in this paper.